The Living Room BV3005 3 Drawer Nightstand Instruction Manual
- September 3, 2024
- The Living Room
Table of Contents
BV3005 3 Drawer Nightstand
Product Information
Specifications:
-
Product Name: Nightstand
-
Model Number: BV3005
-
Components: Nightstand body (A), Legs (B)
-
Hardware: Flat Washers, Spring Washers, Hexagon screws, Allen
Wrench -
Country of Origin: Vietnam
Product Usage Instructions
Step 1: Assembly
1. Turn the Nightstand body (A) upside down on a protective
surface.
2. Attach Legs (B) to Nightstand body (A) as shown in FIG.1.
Step 2: Final Assembly
1. Turn the Nightstand to a standing position.
2. Check the balance of the Nightstand.
3. Tighten all provided hardware to complete the assembly as
shown in FIG.2.
FAQ
Q: Where should I store the Allen Wrench for future use?
A: Store the Allen Wrench in the drawer of the product or use
masking tape to affix it to the underside of the product for easy
access.
Q: What size are the Flat Washers?
A: The Flat Washers are 8192mm in size.
WINNERS ONLY R
ASSEMBLY INSTRUCTIONS
PROD.NO : BV3005
Thank you for purchasing this quality product . Please read instructions thoroughly before unpacking assembly parts Caution: Sharp, exposed staple tips can cause injury. Therefore, for your protection, please remove any exposed staples used in packing.Please keep all hardware parts out of the reach of children. 1. We recommend that you should assemble this product with the assistance of another person; this will make assembly easier and will help to prevent personal injury and to insure parts are not damaged during assembly process. 2. Before beginning,please check packing materials carefully for small parts that may have come loose inside the carton during shipping.Do not discard any packing material until all parts have been located. If any parts are missing, please contact your dealer for prompt replacement. 3. To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residues and rough surfaces and also check for staples or nails left after removing the packing materials .The manufacturer will not be held responsible if preventive steps are not taken prior to installation. 4. Please do not over tighten screws or bolts. During normal use everyday, screws, bolts , nuts and wooden plugs may loosen up.They should be periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause Always check to be sure all hardware on this list and below mentioned components are attached to the furniture property and kept tightened. 5. Please lay all parts and hardware on a non-abrasive surface such as a carpet and follow the assembly.
Components List :
NO.
DESCRIPTION
A
Nightstand body
Q’ TY 1pc
B
Legs
4pcs
TIP: Store the Allen Wrench in assembly in this product drawer or use masking or painter tape to affix it to the underside of the product. This will make it easier to find if you want to periodically tighten bolts or disassemble the product.
Hardware List NO. DESCRIPTION SIZE 1 Flat Washers 8192mm
SKETCH Q’ TY 8pcs
2 Spring Washers 8mm
8pcs
3 Hexagon
5/16″*12mm
4 Allen Wrench 12mm
8pcs 1pc
STEP 1: Turn the Nightstand body (A) upside down on a protective surface such as a carpet or other soft material. Attach Legs (B) to Nightstand body (A) as shown on FIG.1
B
FIG.1
FIG.2
1
2 3
4
A
Step 2: Turn the Nightstand to a standing position. Check the Nightstand
balance and tighten all provided hardware to complete the assembly as shown on
FIG.2
Page 1 of 1
MADE IN VIETNAM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>