Novsight A500-LB3 Screw Less Bezel Dual Color Slim Light Bar Installation Guide
- August 30, 2024
- NOVSIGHT
Table of Contents
A500-LB3 Screw Less Bezel Dual Color Slim Light Bar
“`html
Product Information
SCREW-LESS BEZEL DUAL COLOR SLIM LIGHT BAR
WHITE + AMBER DRIVING BEAM
Specifications
-
Voltage: 9-36V DC
-
3 Beam Pattern Modes
-
Optional Lengths: 10, 13.5, 20, 30, 40, and
50 -
What’s Included: 1 X Light Bar, Side and
Bottom Mount Brackets & Hardware
Dimensions (Example: 20″ Light Bar)
- Length: 545mm (21.46″)
- Height: 71mm (2.80″)
- Width: 41.5mm (1.63″)
- Depth: 40mm (1.57″)
- Mounting Bracket Lengths: 501mm (19.72″) and 527mm
(20.75″)
Mounting Installation Instructions
1. Determine suitable mounting locations to install the LED
light bar, wiring harness, and switch. Once all mounting locations
are confirmed, connect the wires as shown above. Proper insulation
at connections is required.
2. Connect positive and negative wires properly. Press the
switch buttons to test if each mode is functioning properly.
3. Two buttons control white light and yellow light
respectively. Press both at the same time to light up the white and
amber driving beams together.
4. Adjust the light to the desired angle and then secure by
tightening all mounting screws.
FAQ
Q: What gauge wiring harness should be used for different light
bar sizes?
A: For a 50″ light bar, use a 12 AWG one-output
wiring harness; for other sizes, use a 14 AWG one.
“`
SCREW-LESS BEZEL DUAL COLOR SLIM LIGHT BAR
WHITE + AMBER DRIVING BEAM
SPECIFICATIONS:
Voltage: 9-36V DC
3 Beam Pattern Modes:
æ White Driving Beam ç Amber Driving Beam è White + Amber Driving Beam
Optional Length: 10″, 13.5″, 20″, 30″, 40″ and 50″
What’s Included: 1 X Light Bar Side and Bottom Mount Brackets & Hardware
DIMENSIONS:
20″ Light Bar (For Example)
41.5mm
(1.63″)
19.2mm
(0.76″)
501mm (19.72″) 527mm (20.75″)
71mm (2.80″)
60.7mm
(2.39″)
40mm
(1.57″)
545mm (21.46″)
MOUNTING INSTALL INSTRUCTION:
7 8
7
8
Side Mounts SCREW-LESS BEZEL DUAL COLOR SLIM LIGHT BAR
Bottom Mounts
1
WHITE + AMBER DRIVING BEAM
INSTALL INSTRUCTION
Light bar
Fuse
BatteryBattery+
White Driving Beam
Amber Driving Beam
ON/OFF
ON/OFF
Relay
Switch
(Tips: 50″ light bar use 12 AWG one-output wiring harness, other sizes use 14 AWG one)
1. Determine suitable mounting locations to install the LED light bar, wiring
harness and switch. Once all mounting locations are confirmed, connect the
wires as shown above. Proper insulation at connections is required.
2. Connect positive and negative wire properly. Press the switch buttons to
test if each mode is functioning properly.
3. Two buttons control white light and yellow light respectively. Press both
at the same time can light up the white and amber driving beams together.
4. Adjust the light to the desired angle and then secure by tightening all
mounting screws.
SCREW-LESS BEZEL DUAL COLOR SLIM LIGHT BAR
2
WHITE + AMBER DRIVING BEAM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>