Feyree TS-NACS 7KW EV Charger Station User Manual
- August 30, 2024
- feyree
Table of Contents
TS-NACS 7KW EV Charger Station
EV Charging Station
Manual
It is recommended to read the instructions before use
Safety instructions
Warning: The charging station must be grounded (PE) in order to use t
properly Warning: Do not place flammable, explosive or combustible materials,
chemicals, combustible vapors or other hazardous materials near the charging
station.
Warning: Keep the charging plug head clean and dry, if dirty, please wipe
it with a clean and dry cloth, it is strictly forbidden to touch the charging
plug core by hand when it s charged
Warning: t s strictly forbidden to use the charging station when the
charging plug or charging cable s defective, cracked, worn, broken or when the
charging cable is exposed
Warning: Do not attempt to disassemble, repair or modify the charging
station. If you need to repair or modify t, please contact the relevant staff.
mproper operation may cause the charging station damage, water eakage, leakage
of electricity, short circuit, electric shock and other risks
Warning: Use with caution during thunderstorms
Warning: Children should not approach or use the charging station during
the charging process to avoid electric shock
Warning: Do not drive the car while t s charging. You can only start
charging
When the car is stationary. For hybrid Cars, please turn off the engine before
charging
Warning: n case of emergency during the operation of the product, press
the emergency stop button mmediately to cut off all input and output power
Warning: The use of the charging post s prohibited n the following cases
and the manufacturer should be contacted mmediately:
- Charging Station shell is broken
- When the charging cable on the charging station is damaged, cracked, frayed, broken, etc.
- Lightning strikes charging station
- Accidents or fires near charging stations
- Water in the charging station
- The ength of the charging cable on charging station is not ong enough to connect to the car, an extension cable needs to be installed
Product Overview
Brief description:
This product is used for electric vehicle AC charging, the product design is
highly simple, divided into Type2, Type1, GB/T, Tesla four kinds of
specifications. It is equipped with swipe card and plug-and-play charging
methods and multiple safety protection functions. with good dustproof and
waterproof function, can be operated safely outdoor. Type 2 Parameter
introduction
Type2 IEC61851
Power Rating| 7.6KW| 11KW| 22KW
Load balancing| /| | /| | /| |
APP| /| | /| | /| |
RFID Card| /| | /| | /| |
Type A RCD| | | /| /| /| /| /| | /
Type B RCD| /| | /| | | /| | /| | •| /| | /| |
Power supply
system| Single Phase| Three
Phase| Three
Phase
Rated voltage| 85V-264V| 380V±20%| 380V±20%
Rated current| 8-10-13-16-20-25-32A| 8-10-13-16A| 8-10-13-16-20-25-32A
Input Frequency| 50Hz/60Hz| 50Hz/60Hz| 50Hz/60Hz
Protection level| IP65| IP65| IP65
Working
temperature| -35°C — +55°C| -35°C — +55°C| -35°C — +55°C
Storage
temperature| -40°C — +80°C| -40°C — +80°C| -40°C — +80°C
Standby power| <3W| <3W| <3W
Working humidity| 5% – 95%
non-condensation| 5% – 95%
non-condensation| 5% – 95%
non-condensation
LWH| 31016186 mm| 31016186 mm| 31016186 mm
ISpecification| 3G 6gmm,² ++10.5mm²
3G 6mm² +20.5mm ²| 5Gmm²+10.5mm²
5G 2.5mm²+ 20.5mm²| 5G 6mm²+10.5mm²
5G 6mm² + 20.5mm²
Control box function :
- Earth leakage protection (restart recovery)
- 0vervoltage and undervoltage protection (self-test recovery)
- Lightning protection
- 0vercurrent protection
- 0verheat protection
- Grounding protection
- RFI D card function (can be set according to user needs)
- Appointment Time
- WIFI
Product Performance:
- Charging plug according to IEC 62196-2 standard
- Charging control box in accordance with IEC 61851 control principle
- lnsulation resistance: >10000
- Terminal temperature rise: <SOK
- Mechanical life: Charging Plug plugging and unplugging times (Non operating state)>10000 times
- External impact: Charging staion’s Plug can withstand the 1-meter drop and 2 tons of vehicle crushing
- With emergency stop function
Type 1 Parameter introduction
Type 1 SAE J 1772
Power Rating| 7.6KW| | | | 12KW| |
Load balancing| | | | | | | | |
APP| | | | | | | | |
RFID Card| ‘| | | | | | | | | |
Type A RCD| | | | | | | | | | | | | |
Type B RCD| | | | | | | | | | | | | |
Power supply
system| Level 1 and Level 2| Level 1 and Level 2| Level 1 and Level 2
Rated voltage| 85V-264V| 85V-264V| 85V-264V
Rated current| 8-10-13-16-20-25-32A| 8-10-13-16-20-25-32-40A|
8-10-13-16-20-25-32-40-50A
Input Frequency| 50Hz/60Hz| 50Hz/60Hz| 50Hz/60Hz
Protection level| IP66| IP66| IP66
Working
temperature| -35°C — +55°C| -35°C — +55°C| -35°C — +55°C
Storage
temperature| -40°C – +80°C| -40°C – +80°C| -40°C – +80°C
Standby power| <3W| <3W| <3W
Working humidity| 5% – 95%
non-condensation| 5% – 95%
non-condensation| 5% – 95%
non-condensation
LWH| 31016186mm| 31016186mm| 31016186mm
Cable
Specification| 3G 6mm2+10.5mm2 3G 6mm2+20.5mm2 3G10AWG+118AWG
301 OAWG+21 flAWG| 3G 8mm2+ 10.5mm2
3G 8mm2+20.6mm2
2G8AWG+110AWG+118AWG
2G8AWG+1.10AWG+2.18AWG| 3G 10mm2+10.5mm2
3G 10mm2+20.5mm2
2G6AWG+1’8AWG+1-18AWG
2G6AWG+1’8AWG+21-18AWG