OB60SM Series Built in Oven

Product Information

Specifications

• Model: OB60SMPTDG1, OB60SMPTDB, OB60SM16PLG1, OB60SM16PLB1,
  OB60SDPTDX2, OB60SD16PLX1, OB60SD9PLX1

• Product Type: Built-in Oven

• Brand: Fisher & Paykel

• Dimensions:

  • Overall Height: 598mm
  • Overall Width: 596mm
  • Depth of Front Frame: 20mm
  • Depth of Oven Chassis and Front Frame: 565mm

Product Usage Instructions

Prior to Installation

Ensure that some environmental factors and cooking habits can
cause condensation in and around the oven during use. To protect
surrounding cabinetry from possible damage caused by frequent or
excessive condensation, we recommend moisture-proofing the oven
cavity.

After Installation

• Ensure the oven door can open fully without obstruction.

• Make sure the power supply cable does not touch any hot metal
  parts.

• Ensure the isolating switch is easily accessible to the
  customer with the oven installed.

• Complete the ‘Final checklist’ at the end of the
  installation.

• If correct performance cannot be achieved, contact your nearest
  Fisher & Paykel Authorized Service Centre or Customer
  Care.

Installation Milestones

Milestone indicator These milestones represent areas throughout
that are pivotal to an optimal installation outcome. These steps
require additional installer attention and should be quality
checked once completed.

FAQ

Q: What should I do if I encounter condensation in and around

the oven during use?

A: To protect surrounding cabinetry from possible damage caused
by frequent or excessive condensation, we recommend
moisture-proofing the oven cavity.

Q: What are the minimum clearances required for this built-in

oven?

A: The minimum clearances required are:

• Minimum Inside Height of Cavity: 580mm
• Minimum Inside Width of Cavity: 560mm
• Minimum Inside Depth of Cavity: 550mm

BUILT-IN OVEN
MINIMAL OB60SMPTDG1, OB60SMPTDB, OB60SM16PLG1,
OB60SM16PLB1 CONTEMPORARY OB60SDPTDX2, OB60SD16PLX1, OB60SD9PLX1
INSTALLATION GUIDE CN

SAFETY AND WARNINGS

! WARNING!
Electric Shock Hazard Failure to follow this advice may result in electric shock or death. · Before carrying out any work on the
electrical section of the appliance, it must be disconnected from the mains electricity supply.
· Connection to a good earth wiring system is absolutely essential and mandatory.
· Alterations to the domestic wiring system must only be made by a qualified electrician.
! WARNING!
Fire Hazard Failure to follow this advice may result in overheating, burning, and injury. · Do not use adapters, reducers, or branching
devices to connect this appliance to the mains power supply.

WARNING!
To avoid hazard, follow these instructions carefully before installing or using this appliance.
· Please make this information available to the person installing the appliance–doing so could reduce your installation costs.
· This appliance must be installed and connected to the mains power supply only by a suitably qualified person according to these installation instructions and in compliance with any applicable local building and electricity regulations. Failure to install the appliance correctly could invalidate any warranty or liability claims.
· If the power supply cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.
· Isolating switch: make sure this oven is connected to a circuit which incorporates an isolating switch providing full disconnection from the power supply in accordance with the wiring rules.
· The oven must be earthed.
· Do not use adaptors, reducers or branching devices to connect the oven to the mains electricity supply, as they can cause overheating and burning.
· The appliance must not be installed behind a decorative door in order to avoid overheating.
· Please take extra care not to damage the lower trim of the oven during installation. The trim is important for correct air circulation and allows the door to open and close without obstruction. The manufacturer does not accept any responsibility for damage resulting from incorrect installation.

! WARNING!
Cut Hazard Failure to use caution could result in injury. · Take care: some edges are sharp.

IMPORTANT! SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
2

PRIOR TO INSTALLATION
Ensure that:
· The countertop and oven cavity are square and level, and are the required dimensions. · The installation will comply with all clearance requirements and applicable standards and
regulations. · The isolating switch will be easily accessible to the customer with the oven installed. · The electrician provides sufficient free length of power supply cable to reach from the
bottom rear of the cavity to at least 1.5 metres in front of the bottom edge of the opening. · The cable may enter the cavity from the side, top or bottom, but top entry must be at the
rear of the cavity. · The oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear
wall. · The oven will rest on a surface that can support its weight. · The height from the floor suits the customer. · You consult local building authorities and by-laws if in doubt regarding installation.
IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend moisture- proofing the oven cavity.
AFTER INSTALLATION
z The oven door can open fully without obstruction. z The power supply cable does not touch any hot metal parts. z The isolating switch is easily accessible to the customer with the oven installed. z You complete the `Final checklist’ at the end of the installation. z If, after following the instructions given, correct performance cannot be achieved, please
contact your nearest Fisher & Paykel Authorised Service Centre, Customer Care, or contact us through our local website listed at the end of this document.

INSTALLATION MILESTONES
Milestone indicator These milestones represent areas throughout that are pivotal to an optimal installation outcome. These steps require additional installer attention and should be quality checked once completed.
MILESTONE LINKS
Ensure both hinges are fully locked before shutting the door.
Align oven with surrounding cabinetry and appliances.

3

Supplied

PARTS

Screws (2)

Metal side shelves fixing nut (2)

COMPONENTS
Not supplied

TOOLS

Powered driver

Cross-head screwdriver

4

g
POWER OUTLET LOCATION

PRODUCT DIMENSIONS

c

m

PLAN VIEW

j

h

l

b 596

FRONT VIEW

5

d

DATUM : FRONT OF CHASSIS

p
o k
a 598

DATUM : FRONT OF CHASSIS
n E 545

Product Dimensions a Overall height of oven B Overall width of oven c Depth of front frame (excludes dial, handle and front stainless
trim) d Depth of oven chassis and front frame (excludes dial, handle
and front stainless trim) E Depth of chassis F Height of chassis G Width of chassis h Height from bottom datum to top of oven door i Distance from bottom datum to bottom of door j Height of control panel k Height of stainless steel cap on control panel l Height from bottom datum to centreline of handle m Width of handle n Depth of handle (measured from front of door) o Thickness of handle p Depth of door (open) (measured from front of door)

mm 598 596
20
565
545 475 556 487
12 100 20 464 565
42 16 460

Minimum Clearances

mm

Minimum inside height of cavity

580

Minimum inside width of cavity

560

Minimum inside depth of cavity

550

f

IMPORTANT NOTE: Throughout this guide, dimensions may vary by ±2mm

(1/16″)

i p

PROFILE VIEW

DATUM : BOTTOM OF CHASSIS

INDICATES PRODUCT DATUM ——————————————INDICATES CABINETRY CLEARANCES ——————————–

c

d

a

CABINETRY DIMENSIONS
e b

PROFILE

PLAN

CABINETRY DIMENSIONS

MM

A Minimum inside width of cavity

560

B Overall width of cabinetry

600

C Overall height of cabinetry

600

D Minimum inside height of cavity

580

E Minimum inside depth of cavity

550

If installing a cooktop above the oven, ensure adequate clearance is provided as per the cooktop manufacturer’s instructions.

6

PROUD INSTALL 16-20mm
FLUSH INSTALL 16-20mm
2mm

CHECK CAVITY

UNPACK PRODUCT

z Do not lift or move the product using the handle.

z Keep all packing materials until the unit has been inspected.

z Inspect the product to ensure there is no shipping damage. If any damage is

Measure cavity dimensions. Ensure all

detected contact the dealer or retailer you brought the product from to report the

1

minimum specifications have been met.

damage.

Refer to page 6.

z Fisher & Paykel is not responsible for shipping damage.

1

Cut all straps and remove the carton top cap.

2

For dark cabinetry, ensure clashing has been considered and installed.

2

Lift the carton sleeve and remove any transit packaging.

Ensure service access complies with

3

local requirements. Refer to page 8 for

details.

3

Set aside any accessories.

4

Ensure any cooktop ventilation requirements have been considered.

4

Dispose responsibly.

7

REMOVE DOOR

CONNECT POWER

z This oven must be connected to the mains power supply only by a suitably qualified person.
z This oven must be earthed.

Open the door and remove all cable ties

1

and packaging holding the oven shelves

in place.

Before connecting the oven to the mains power supply, check that:

the domestic wiring system is suitable for the power drawn by the oven (as specified on the rating plate)

the voltage corresponds to the value given on the rating plate.

MODEL CODE

MAX POWER (W) HZ

VOLTAGE (V) AMPS (A)

OB60S

2800 – 3300

50 – 60 Hz 220 – 240 V~ 12.8 – 13.8

2

Grip the shelves at the front, making sure to hold the wire shelf and frame

together. Lift upwards and pull out from

the oven.

3

Locate the hinge locks on either side of the door. Push the locks upwards to

1

Unclip and lift cover to access terminal block.

release.

Connect to terminal block as shown.

4

Holding the door on both sides, partially

2

close the door and carefully pull the

door away from the hinges.

Ensure oven is correctly Earthed and cable clamp is tightened before closing the cover.

8

POSITION OVEN INTO CAVITY

Some models only*:

For dark cabinetry, the supplied trim can

1

be used to enhance clashing finish.

1

To install, remove the trim adhesive and press to secure to cavity.

2

Lift product into cavity.

2

3

REFIT DOOR
Holding the door on both sides, carefully lift door back onto the hinges.
Open the door fully and push each locking lever down and lock into place.
Ensure both hinges are fully locked before shutting the door.

*Model code 565881. To purchase cabinetry trim as an optional accessory, visit fisherpaykel.com 9

ALIGN AND SECURE

Align oven with surrounding cabinetry

1

and appliances.

2

Using the product as a guide, pre-drill 2 x 3mm pilot holes.

3

Secure oven to cavity using the 2 x #7×13 pan head screws provided.

10

REFIT SHELVES
Sliding shelves Place shelves back into the oven at the desired level. Ensure shelves are level and correctly positioned with the guard rail at the back.
Wire shelves Slide shelves into the cavity.
Clip on sliding shelf supports Ensure the slides are positioned the correct way around, with the triangular tab at the front. Fit the top clips over the side rack. The front clip should be fitted as close to the front of the side rack as possible. Make sure the rear clip has engaged. Click the bottom clips into place.

TEST OVEN
Follow the guidance on screen to ensure oven turns on and heats correctly. Refer to your User Guide for more information.

INSTALLER CHECKLIST
TO BE COMPLETED BY THE INSTALLER
Ensure the oven is level and securely fitted to the cabinetry.
Check the lower trim is undamaged.
Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim. This is to ensure correct air circulation. Should the lower trim become damaged, straighten the trim and ensure the oven door opens fully without obstruction.
Ensure you remove all internal packaging (including the circular yellow packing retainers holding the accessory box in place).
Ensure all oven vents and openings are clear and free of any obstruction or damage.
Failure to make sure all oven vents are clear may result in poor product performance. Ensure the isolating switch is accessible by the customer.

Complete and keep for safe reference: Model Serial No. Purchase Date Purchaser Dealer Address Installer’s Name Installer’s Signature Installation Company Installation Date
11

F I S H E R PAY K E L .C O M
© Fisher & Paykel Appliances 2024. All rights reserved. The models shown in this guide may not be available in all markets
and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time. For current details about model and specification availability in your country,
please go to our website or contact your local Fisher & Paykel dealer.
431323A 04.24

References

• Shop Luxury Kitchen Appliances | Fisher & Paykel United Kingdom
• Shop Luxury Kitchen Appliances | Fisher & Paykel Australia

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>