NOVASTAR MBOX600 Pro Industrial Controller Owner’s Manual
- August 29, 2024
- NOVASTAR
Table of Contents
Specifications
MBOX600 Pro Industrial Controller Specifications
MBOX600 Pro Industrial Controller
Change History
Document Version | Release Date | Description |
---|---|---|
V1.0.0 | 6/7/2024 | First release |
Introduction
The MBOX600 Pro is an LED display controller created by NovaStar. It
integrates an industrial PC and the sending capability. This controller is
used outdoors and applies to the scenarios where no PC is used for LED display
control, for example, fixed outdoor displays.
A mouse, keyboard and monitor can be connected to the MBOX600 Pro for software
installation, screen configuration, content playback, etc. Working with
VNNOXCare Configuration and LCT Lite, the MBOX600 Pro can enable remote
control, cabinet configuration, local playback, playback preview and more.
Certifications
EMC, CE RED, CE ROHS, CQC, SRRC, IC, IC ID, FCC SDoC, FCC ID, UL, CB, RCM
If the product does not have the relevant certifications required by the
countries or regions where it is to be sold, please contact NovaStar to
confirm or address the problem. Otherwise, the customer shall be responsible
for the legal risks caused or NovaStar has the right to claim compensation.
Features
-
4x Gigabit Ethernet outputs and pixel capacity: up to 2,600,000
-
Output scaling
− The pixel width ranges from 64 to 4096.
− The pixel height ranges from 64 to 1920.
− Total pixel capacity cannot exceed 2,600,000. -
Common resolutions supported: 1366×768, 1440×900, 1600×900, 1920×1080, 2048×1152
-
1x Stereo audio output
-
1x HDMI 1.3 output (for image output or output preview)
-
Connecting to a display and allowing for output scaling on an LED display
-
1x HDMI 1.3 input
-
In synchronous mode, this connector is used as the input source.
-
2x USB 2.0 and 2x USB 3.0
Connecting to peripherals such as a mouse, keyboard and USB drive -
2x Sensor connectors
Connecting to a light sensor or temperature and humidity sensor -
1x 6-pin Phoenix connector
Connecting to a central control device, or control the power on and off of the connected device -
2x Gigabit Ethernet ports
One for communication and the other for remote management of device networking
Appearance
Front Panel
Name | Description |
---|---|
Power button | |
RESET | Factory reset button |
Press and hold this button for 10 seconds to reset the product to its factory
settings.
USB 2.0| 2x USB 2.0
Connecting to peripherals that support the USB protocol, such as a mouse,
keyboard, and USB drive
SIM| SIM card slot
Capable of preventing users from inserting a SIM card in the wrong
orientation.
SOURCE| Button for switching between synchronous mode and asynchronous mode
FN 1| Custom button (to be implemented in future updates)
FN 2| Custom button (to be implemented in future updates)
| Ethernet port (default IP address: 192.168.0.10)
Connecting to a router for remote management of device networking
Rear Panel
Name | Description |
---|---|
LED OUT | 4x Gigabit Ethernet outputs |
LED OUT | Maximum pixel capacity: 2.600.000 |
When scaling is enabled, the maximum capacity is 2,600,000 pixels. (The pixel
width ranges from 64 to 4096 and the pixel height ranges from 64 to 1920.)
SENSOR 1| Connecting to a light sensor or temperature and humidity sensor
SENSOR 2| Connecting to a light sensor or temperature and humidity sensor
WIFI| Connecting to a Wi-Fi antenna
4G/5G| Connecting to a 4G/5G antenna
AUDIO OUT| Audio output
HDMI OUT| lx HDMI 1.3 output
HDMI IN| lx HDMI 1.3 input
USB3.0| 2x USB3.0
Connecting to peripherals that support the USB protocol, such as a mouse,
keyboard, and USB flash drive.
ETHERNET| Gigabit Ethernet port
Connecting to the control computer, or connecting to a LAN or public network
for content publishing and screen control
| lx 6-pin Phoenix connector for communication with and control of all central
control devices that support RS232.
RELAY denotes a relay connector for controlling the power on and off of the
connected device.
I/O denotes a connector that will be implemented in future updates.
| Power input
Indicators
Indicator | Color | Status | Description |
---|---|---|---|
PWR (Power indicator) | Red | Staying on | The system is powered on and in |
standby mode
Off| No power supply or powered off
HDD (Hard disk drive indicator)| Green| Flashing| HDD is functioning namely.
Off| Powered off
RUN (FPGA indicator)| Green| Staying on/off| FPGA not loaded/no clock
Flashing 2 limes every second| Video source accessed
Flashing once times every 2s| No video source
Flashing 4 limes every second| The primary Ethernet port fads and
the backup port iscurrently in use.
VAFI (WI-Fl network indicator)| Green| Staying on| Wi-Fi network connection
normal
Off| No Vie-Fi network connection
4G/5G (4G/5G network indicator)| Green| Staying on| Network normal
Flashing 4 limes every second| 46/56 module detected but network abnormal
Off| No 4G/5G module detected
HDMI (Synchronous source/ external source indicator)| Green| Staying on|
Selected but video source abnormal
Flashing 2 times every second| Selected and video source accessed
Off| Not selected
IPC (Asynchronous source/ internal source indicator)| Green| Staying on|
Selected but video source abnormal
Flashing 2 limes every second| Selected and video source accessed
Off| Not selected
Applications
The HDMI connector can be connected to a monitor to inspect the playback on an LED display, as well as to install software and configure the product.
Dimensions
Specifications
Performance | CPU | N97: 4 cores. 3.6 GHz |
---|---|---|
RAM | 4 GB (9U4A3) |
8 GB (9U8A4)
HDD| 128 GB (9U4A3)
256 GB (90844)
Connectors| Front panel
connectors| 2x USB20
lx Gigabit Ethernet port
Rear panel
connectors| 4x LED Output Ethernet ports
2x Sensor connectors
lx Wi-Fi antenna connector
lx 4G/5G antenna connector
lx Audio output
lx HDMI output
lx HDMI input
2x USB 3.0
2x Sensor connectors
lx Gigabit Ethernet port
lx 6-pin phoenix connector
lx Power input connector (DC 12 V)
Maximum Capacity| 2.600.000 pixels
Maximum Power Consumption| 34 W
Operating Environment| Temperature| -20<C to •60°C
Humicrrty| 0% RH to 80% RH. non-condensing
Storage Environment| Temperature| -40’C to +80°C
Physical Specifications| Dimensions| 3190 mm x 1359 mm x 45.5 mm
Net weight| 1778.0 g
Packing Information| Dimensions| 361.0 mm × 334.0 mm × 141.0 mm
Accessories| • 1x Power adapter
• 1x Power cable
• 2x Racks
• 6x Screws
• 1x Certificate of Approval
The amount of power consumption may vary depending on various factors such as product settings, usage, and environment.
Models
CPU: 9U denotes N97.
RAM: 4A denotes 4 GB and 8A denotes 8 GB.
HDD: 3 denotes 128 GB and 4 denotes 256 GB.
Operating System | Model | CPU | RAM | HDD |
---|---|---|---|---|
Linux/Windows 10/Windows11 | MBOX600 Pro (9U4A3) | N97 | 4GB | 128GB |
MBOX600 Pro (9U8A4) | N97 | 8GB | 256GB |
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense. This
equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.
Copyright © 2024 Xi’an NovaStar Tech Co., Ltd. All Rights Reserved.
No part of this document may be copied, reproduced, extracted or transmitted
in any form or by any means without the prior written consent of Xi’an
NovaStar Tech Co., Ltd.
Trademark
is a trademark of Xi’an NovaStar Tech Co., Ltd.
Statement
Thank you for choosing NovaStar’s product. This document is intended to help
you understand and use the product. For accuracy and reliability, NovaStar may
make improvements and/or changes to this document at any time and without
notice. If you experience any problems in use or have any suggestions, please
contact us via the contact information given in this document. We will do our
best to solve any issues, as well as evaluate and implement any suggestions.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any inte rference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interferenceto radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
ISED Statement
This device complies with Industry Canada license‐exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device. The
digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
Official websitewww.novastar.tech
Technical supportsupport@novastar.tech