Black Diamond Honeybee Ballpoint Pen Kit Instructions

August 29, 2024
BLACK-DIAMOND

Black Diamond Honeybee Ballpoint Pen Kit

Product Information

Specifications

  • Product Name: Honeybee Ballpoint Pen Kit
  • Required Accessories:
    • 7mm pen mandrel
    • 3piece Honeybe e B ushing Set
    • 10m m & 25/64” Drill bit
    • Unive rsal Barr el Tr immer
    • Live T ail stock C ente r
    • 2 part ep oxy gl ue or instacure glue
    • Mi nimum Bl ank size: 3/4” x 3/4” x 2-5/32”

Product Usage Instructions

Preparing the Blanks:

  1. Select the desired material for your pen blanks.
  2. Cut the material to the appropriate size for the pen kit.
  3. Ensure the blanks are smooth and free of any imperfections.

Turning the Blanks:

  1. Secure the blank in a lathe using the appropriate chuck or mandrel.
  2. Use turning tools to shape the blank into the desired pen design.
  3. Sand the blank to achieve a smooth finish.

Pen Assembly:

  1. Insert the pen refill into one end of the pen barrel.
  2. Attach the pen components according to the kit instructions.
  3. Ensure all parts fit securely and align properly.

FAQ

  1. Q: What type of refill does the pen kit use?
    A: The Honeybee Ballpoint Pen Kit typically uses a standard ballpoint pen refill.

  2. Q: Can I use different materials for the pen blanks?
    A: Yes, you can use a variety of materials such as wood, acrylic, or resin for the pen blanks as long as they are compatible with turning.

Preparing the Blanks

  • Prepare a master blank of at least 3/4” square. Cut two sections to the length of each tube. (Add 1/16” for trimming)
    Mark the center of each blank.

  • Drill a centered hole lengthwise through each blank.
    Upper blank (shorter tube)—drill a 10mm hole through.
    Lower blank (longer tube)—drill a 25/64” hole through.

  • Glue each tube in the proper blank. Spread the glue over each tube. Insert the tube into the blank with a twisting motion to spread the glue evenly inside. Center each tube lengthwise inside the blank.

  • When glue dries, square the ends of each blank.

Turning the Blanks

  • Mount the bushings and blanks on the mandrel according to the Diagram above.
  • Thread on the knurled nut and hand tighten to hold all components in place.
  • Slide the tailstock up snugly against the mandrel shaft inserting the live center point into the mandrel dimple, lock in place.
  • Hand tighten the quill adjustment to firm up the mandrel. (DO NOT overtighten, it could damage the mandrel.
  • Using sharp tools, turn the blank down close to the bushing diameter. Turn the barrel (straight or to a profile of your choice)
  • Sand the blank down to be flush with the bushings gradually increasing the sandpaper grits.
  • Finish the barrel with your choice of polish. Allow sufficient time for the polish to cure.

Pen Assembly

NOTE: Line up the components according to the above picture.

  • Press the tip into one end of the lower tube (longer tube)
  • Press the center band coupler into the opposite end of the lower tube.
  • Remove the protector off the refill, insert the spring over and drop into the opening at the center band coupler.
  • Screw the twist mechanism over the refill end.
  • Press the center band into the end of the upper tube(shorter tube)
  • Press the tube support/ cap coupler into the opposite end of the upper tube.
  • Put the pen clip on the cap coupler, then screw the cap over the cap coupler.
  • Engage both ends to close the gap in the center.
  • The pen operates by twisting the ends to extend or retract the refill.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals