HEYGEARS RS Reflex Professional Grade Printer Instruction Manual
- August 28, 2024
- HEYGEARS
Table of Contents
HEYGEARS RS Reflex Professional Grade Printer
Please make sure to read and understand this Quick Start before unpacking
and installing.
Thank you for choosing HeyGears. For your safety, please operate as per this
Quick Start. If you fail to comply with the instructions in this manual,
HeyGears will not be liable for the consequential damages unless required by
all applicable laws and regulations. Please keep this operation manual
properly for future reference. The pictures are for reference only and the
products are subject to the actual product.
Items & Parameters
Components
Installation Requirements
Operation Steps
Steps 1
Place the printer on a level, stable table, and check its appearance to
confirm if it’s in good condition. Lift the hood to its highest position. Plug
the provided power cord in the power port, connect it to the power supply, and
turn on the power switch. The touch screen lights up, indicating the power is
successfully connected.
- Please DO NOT remove the filler in the cabinet before connecting to power.
Steps 2
Wait until the printer’s main axle rises to the top, and then remove the
filler from the cabinet. Follow the onboard guide on the touch screen to
finish the installation. 
Steps 3
Afterward, please download Blueprint Studio from
https://www.heygears.com/SAP/ Blueprint, follow its onboard guide for print
preparation (pre-processing), and send the finished printable slice file to
your Reflex RS. Then print it on your printer by operating on the printer’s
touch screen. Videos of guides are available in the Help Center on Blueprint
Studio. 
Steps 4
When printing is done, open the hood, unlock it, and take out the build
platform. Then follow the instructions for post-processing like washing, part
removing, support removing and post-curing, etc.
Release Film Replacement
Images below are examples of the resin tank and the spare release film.
STEPS 1
Remove the resin cartridge. Then unscrew (counterclockwise) the bolts on
both sides of the resin tank, and lift the tank to remove it. If there’s resin
or any residues in it, make sure to clean it well, and only then can you
remove its release film. 
STEPS 2
Remove all the screws on the release film from the bottom of the resin tank
with the provided wrench. Then remove the film.
STEPS 3
Set up a new release film back onto the tank. Screw back tight the screws
on the diagonals and then other screws. When the film is installed well in
place, its frame should be level with the resin tank frame. Mount back the
tank onto the printer.
Cautions
- Always remember to close the hood in time whenever you open it for operation. Do NOT open the hood during printing, or print precision might be affected due to dust, vibration or so.
- Plastic components such as the hood and touch screen are not resistant to long-time exposure to resin or alcohol. Please wipe them clean if there’s resin or alcohol on them.
- Please place the printer and resin cartridges properly, away from any light, dust, or direct sunlight, or if printing quality or precision might be affected.
- Keep the device away from fire.
- When you use your Reflex RS, please pay attention to whether there’s any resin on the projection screen. If any, it indicates that the resin tank’s release film might have been broken and is leaking resin, which might cause ddamageto the printer. In this case, clean off the resin as soon as possible, enter the printer’s settings, and project a pure white image to check the printer’s condition. If the printer does not work properly, please contact HeyGears Support.
FCC STATEMENT
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, under Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used by the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- heygears.com
- info@heygears.com
- Tel: +1 318-353-4295 (Global)/ +1 949-418-9418 (USA) / +44 148-396-8549 (EU)
- USA-17931 Sky Park Circle, Suite E, Irvine, CA, 92614 CHN-Block B2, 501, 601, Enterprise Accelerator, Kaifa District, Guangzhou City
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>