Virtufit TR-75 Loopband Treadmill User Manual

Virtufit TR-75 Loopband Treadmill

Instagram: @virtufit _fitness
Youtube: VirtuFit
Website: www.virtufit.com

SAFETY INSTRUCTIONS

WARNING:
Now here we suggest that you should consult with your physician or health professional before starting your workout, especially for the age up to 35 old or once-health problem people. We take no responsible for any problems or injuries if you don’t following our specication. Treadmill will be carefully assembled and covered the motor shield, then connect to the power.

ATTENTION

• Ensuring the safety clamps were attached to the clothing or belts before using the treadmill.
• Please do not insert any items to any part of the equipments, which would damage the equipment.
• Position the treadmill on a clear, level surface. Do not place the treadmill on thick carpet as it may interfere with proper ventilation. Do not place the treadmill near water or outdoors.
• Never start the treadmill while you are standing on the walking belt. After turning the power on and adjusting the speed control, there may be a pause before the walking belt begins to move, always stand on the foot rails on the sides of the frame until the belt is moving.
• Wear appropriate clothing when exercising on the treadmill. Do not wear long, loose toting clothing that may be caught in the treadmill. Always wear running or aerobic shoes with rubber soles.
• Keep the children and pets away from the treadmill while starting workout.
• Don’t exercise in 40 minutes after dinner.
• The equipment is suitable for adults, children need be accompanied with adults while workout.
• You must hold on to the handrails until you become comfortable and familiar with the treadmill when it is your rst workout.
• Treadmill is indoor-using equipment, not outdoor-using for avoiding damage. Keep the store-place clean, at and drying. Prohibiting the other purpose using, only for workout.
• Please purchase the power-line to the distributor or contact with our company directly, for the powerline only equip to the treadmill.
• The treadmill is for indoor and not outdoor use to prevent damage on the product. Keep the storage area dry, clean and at. It is forbidden to use the device for other purposes than before training.
• Only use the power cable supplied by the supplier for the treadmill. If the cable is missing, please contact our company.
• If the treadmill should suddenly increase in speed due to an electronics failure or the speed being inadvertently increased, the treadmill will come to a sudden stop when the pull pin is disengaged from the console.
• Do not connect line to the middle of cable; do not lengthen cable or change the cable plug; do not put any heavy thing on cable or put the cable near the heat source; forbid using socket with several holes, these may cause re or people may be hurt by the power.
• Cut o the power when the equipment is not used. When the power is cut o , do not pull the power line to keep the wire unbroken. Insert the plug to the socket with the safety ground circuit, for the power-line is professional equipment. You must contact with the professional people directly while the line is damaged.
• This Treadmill only for home-using, the max user weight is 110 KGS.
• Please keep the space at least l to 2 meter at the end of base frame to escape any accidents!

Warranty claim is excluded if the cause of the defect is the result of:

• Maintenance assembly and repair work not carried out by an official dealer.
• In the event of improper use, neglect and/ or poor maintenance.
• Failure to maintain the fitness equipment in accordance with the manufacturer’s instructions (see the enclosed manual).

CHECKLIST

TOOLKIT

When you open the carton, and you will find the below parts in the carton:

ASSEMBLY INSTRUCTIONS

Missing parts: If you think you are m1ss1ng certain parts in your package, carefully check the styrofoam and the treadmill. Some parts (bolts, screws, etc.) are already attached to/ in the treadmill.
Socket screws: The treadmill contains socket screws, make sure that the alien key is firmly in the bolt before you apply force to the key. In this way you prevent the head of the socket head screw from being rotated.

STEP 1

• Remove 4 screws and 4 corrugated rings from the lower part of the bag and attach the left and right uprights to the base frame.

STEP 2

• Fasten the panel with the uprights by M8 screws and M8 washers.

PAY ATTENTION: Do not press the cables in the uprights during assembly.

• Secure the pull knob to the left upright.

STEP 3

• Use the security button to attach the base support to the base frame and place then the safety key in the yellow area on the panel.
• The device is now fully assembled.

FOLDING INSTRUCTIONS

If you need to fold the machine, please take o the x knob (Part serial No. is 6) and put into panel cup- holder. Then fold up the machine and fix by stretch knob (Part serial No. is 7. Please take out the two pins on incline blocks while folding). To spread the machine, just pull the stretch knob, put down the machine, then x the knob and pins.

MAINTENANCE

LUBRICATING THE BELT
RUNNING BELT AND DECK LUBRICATION
This treadmill is equipped with a pre-lubricated, low maintenance deck system. The belt/ deck friction may play a major role in the function and life of your treadmill, thus requiring periodic lubrication. We recommend a periodic inspection of the deck. You need contact with our service center if you nd the damage of the deck.

We recommend lubrication of the deck according to the following timetable:

• Light user (less than 3 hours/ week) annually
• Medium user (3-5 hours/ week) every six months
• Heavy user (more than 5 hours/ week) every three months

Best indicator is to lubricate when the walking platform feels dry. We recommend that you buy the lubrication from our distributor or directly to our company.
ATTENTION: Any repair needs to be done by a professional technician unless otherwise suggested by the supplier.

• We suggest that you should cut o the power for 70 minutes after keep running 2 hours, so that it’s good for maintain the treadmill.
• For avoiding the slipping during running, the belt not too loose; for avoiding the more abrasion between the roller and belt and maintain the machine’s good running ,the belt not too tight. You can adjust the distance between plates and belt, the belt be away from the plates about 50-75 mm on both sides, if the best not too tight and loose.

We strongly recommend that you do the following

• Switch of and remove the power cable from the wall after every use, especially if children are present.
• Clean your treadmill after use.
• Use a dry cloth to clean the control panel and areas around the power switch. Use a soft clean cloth and cleanser to remove stubborn stains and dirt o the running belt.
• Tighten the running belt once a month.
• Keep your treadmill in a safe dry place away from heat and water.

USAGE OF SILICONE OIL

Pull up tightly of the running belt. Then put the silicone oil to running board. Then start the machine to running 3 minutes without loading. It is better to maintain like this every 30 hours working of the machine. This can save lifetime of parts properly.

We recommend that you do the following:

• Disconnect the power cord after every use, especially when children are present.
• Clean the treadmill after use.
• Use a dry cloth to cover the control panel and areas around the on/o switch clean.
• Use a soft clean cloth and detergent to remove stubborn stains and dirt from the treadmill.
• Tighten the treadmill once a month.
• Keep your treadmill away from heat and water in a safe, dry place.

Regular maintenance prolongs the life of your treadmill and prevents injury!

RUNNING BELT ADJUSTMENT

1. Running belt deviates to left
   Start the machine, set speed at 2-3 km/h without a load on the belt, use Allen key to turn the screw l/4 turn (see g. l). Then allow the machine to run without a load for l-2 minutes. Repeat process until the belt becomes central.

2. Running belt deviate to right
   Start the machine, set speed at 2-3 km/h without a load on the belt, use Allen key to turn the screw l/4 turn (see g. 2). Then allow the machine to run without a load for l-2 minutes. Repeat process until the belt becomes central.

3. Running belt jam
   If the running belt is in dead condition, use the Allen key to turn the screw l/2 a turn both left and right until the jam solved (see g 3).

INCLINATION ADJUSTMENT
There are incline blocks on both sides of the machine. It has 3-level inclination. Please use the pins to adjust the incline level. Please note the pins must in the same position for both sides while adjusting the lever.

CONTROL PANEL

KEY DEFINITION

1. Press “START” key, the machine will start by 0,8 km/h after 3 seconds.
2. Press”+” key for speed up and”-” key for low down. The fastest speed is 70,0 km/h and lowest is 0,8 km/h.
3. Press “MODE” key, the screen will show Speed, Time, Calories. And the scan light will light from speed, time, calories every 5 seconds.
4. The treadmill has 72 programs from P7-P72. While on stand-by, press “PROG” to set the programs then press “START” to start the machine.
5. If you need to use auto program, please select it rst when the machine is on stand­by.
6. For emergency stop, please pull out the safety key. The machine will stop very slowly. Pull out safety key and the screen will show “ERR”, put it back and on it will show “OFF”.
7. Touch the heart sensors, the screen will show heart rate frequency.
8. Left handrail has “start/stop” keys. The right handrail has speed shortcut keys + & – to adjust speed.
9. Press “STOP” key to stop the machine after using.

PROGRAMS

Display monitor has 12 programs from Pl-Pl2. While on standby mode, press “PROG” to set the programs then press “START’ to start the machine. For example, after activating the treadmill, press “PROG” immediately to enter the programs. Or press “STOP” 2 times to get in to standby mode. Below you can see the programs. The horizontal line represents time, each dot represents 1,5 minute. The vertical line stands for speed, each dot represents lkm/h. Each program lasts 30 minutes .

While the machine is in use and running, during the auto programs the(-) and (+) keys are not available. If you want to stop the auto programs, select “STOP” or remove the safety key, then turn on again or palce safety key back on. Then select desired speed. For emergency stop, please pull out the safety key. The machine will stop very slowly. Pull out safety key and the screen will show “Err”, put it back and on it will show “OFF”. Press “STOP” key to stop the machine after using.

EXPLODE DRAWING

PARTS LIST

TROUBLE SHOOTING

TRAINING INSTRUCTIONS
A successful exercise program consists of a warm-up, aerobic exercise, and a cool-down. Do the entire program at least two and preferably three times a week, resting for a day between workouts. After several months, you can increase your workouts to four or ve times per week.

WARMING UP
The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two to ve minutes before strength-training or aerobic exercising. Perform activities that raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging, jumping jacks, jump rope, and running in place.

STRETCH

Stretching while your muscles are warm after a proper warm-up and again after your strength or aerobic training session is very important. Muscles stretch more easily at these times because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held for 75 to 30 seconds.

COOLING
The purpose of cooling down is to return the body to its normal or near normal, resting state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to return to the heart.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>