TRACTIAN SR-PRO Smart Receiver Pro Instruction Manual
- August 20, 2024
- TRACTIAN
Table of Contents
TRACTIAN SR-PRO Smart Receiver Pro
About your Smart Trac Receiver Pro
TRACTIAN System
- By monitoring assets online and in real-time, the TRACTIAN system guarantees solutions to optimize daily maintenance management.
- The system integrates vibration and temperature sensors with mathematical models, generating alerts that avoid unwanted shutdowns and high costs resulting from unexpected failures.
- Fault detection
TRACTIAN’s
- unique analysis system enables accurate fault detection. The algorithms are constantly trained based on feedback from field analysis, always under the supervision of our vibration specialists. Thousands of spectra are
- collected daily in a system that pinpoints asset failures before they happen.
Real-time data
- Collections and analyses are displayed intuitively on TRACTIAN’s online platform, which is easily accessible from a computer or cell phone, enabling integrations with other systems.
- The platform also allows for complete main-tenance control with hour meters, energy con-sumption, and automatic calculation of asset indicators.
Smart Receiver Pro
- The Smart Receiver Pro is a transmitter responsible for receiving sensor data and sending it to TRACTIAN’s platform. The data is sent via the 2G, 3G and 4G/LTE mobile network via the best available operator in the region, selected
- automati-cally. If necessary, data can be sent via a Wi-Fi network.
Installation
- Smart Receiver Pro supports up to 100 sensors within a radius of 100 meters (330 feet) with obstacles and 1 kilometer (0.62 mile) in the open field, depending on the topography of the plant.
- To install more sensors or cover greater distances, more receivers are required. It is recommended to position the receiver in an elevated location, centered in relation to the sensors.
- DO NOT place the device on surfaces that reach a temperature above 230°F.
- DO NOT clean the device with solvents such as Acetones, Hydrocarbons, Ethers, or Esters.
- DO NOT subject the device to submersion.
- DO NOT subject the device to excessive mechanical impact, dropping, crushing or friction.
- TRACTIAN doesn’t take responsibility for damages caused by the use of devices outside the standards defined in this manual.
Activation
Before installing the devices, activate your access to the platform as follows:
Smart Receiver Ultra
TRACTIAN’s Smart Receiver Pro requires an external power supply. So make sure there are electrical connections near the installation site.
DO NOT set up the Smart Receiver Pro inside metal electrical panels, because these may block the receiver’s signal. As for other types of electrical panels, such as plastic ones, there is no risk to receivers.
Range & Reach
The receiver supports a maximum distance of 100 meters (330 feet) from the
sensors with obstacles and 1 kilometer (0.62 mile) in the open field. It can
communicate with up to 100 sensors, depending on the case. For this reason, to
obtain the best results in places with a large number of assets, it is
recommended to use more receivers in the same area.
Installation
- This device must be professionally installed.
- The number of receivers to be installed depends on the number of sensors installed and plant topology.
- Only use the antenna that is provided with the device.
- In an open field, it is necessary a direct view between the sensor and the receiver.
- This device is designed and tested for industrial environments.
Installation Site
For best results, set up the receiver only in elevated places with the antenna in front of the sensors. Also note areas with no obstacles between the sensors and receiver.
- Ideal
- Not ideal, but acceptable
- Inadequate position
- Smart Trac Pro Sensor
Connection
Mobile Network
- The Smart Receiver Pro connects automatically to the best available LTE/4G network in your region.
Wi-Fi
- In case there is no mobile network available or you would rather connect it to a Wi-Fi network, the connection is possible. When plugged into the power outlet, the receiver will turn on a white light and generate its own network that
- can be found in the Wi-Fi settings of nearby devices (such as smartphones or computers). By connecting your device to the receiver’s temporary network, you will see a form that must be filled out with your company’s Wi-Fi
- information so the receiver can connect to it.
The receiver’s own network will be generated 10 seconds after it is plugged in. If no device connects within 1 minute, the receiver will search for the best available mobile network.
Technical Specifications
Smart Receiver Pro Technical Specifications
Connections
Physical input Physical output
| ****
Power supply and external antennas (Mobile and Wi-Fi) LED indicates operating status
---|---
Wireless Communication
Frequency Protocol Bands
Sensor connectivity
| ****
915 MHz ISM and 2.4GHz ISM
IEEE 802.15.4g and IEEE 802.11 b/g/n
2.4 GHz: 14 frequency channels, dynamically defined Up to 100 sensors within a 100m (330 feet) radius with obstacles or 1km (0.62 miles) in the open field
Host Network Commun.
Mobile
Mobile Frequencies
Wi-Fi Network
| ****
LTE (4G), WCDMA (3G) e GSM (2G)
LTE B1/B2/B3/B4/B5/B7/B8/B28/B66/B40 WCDMA B1/B2/B5/B8
GSM 850/900/1800/1900 MHz
802.11 b/g/n, 2.4 GHz, WPA2-Personal and WPA2- Enterprise
Wi-Fi Configuration
Wi-Fi network setup
| ****
Captive Portal through a smartphone or a computer
Physical Characteristics
Dimensions
Attachment Weight
External Material Building
| ****
86mm / 3.4in (W) x 61mm / 2.4in (H) x 35mm / 1.4in (D), excluding power supply and antennas
Attached by magnets
180g or 6.35oz, excluding power supply Makrolon 2407
Environmental Characteristics
Operation Temperature Humidity
Hazardous Area Rating
| ****
From –10°C to +60 °C (14°F to 140°F)
Maximum 95% of relative humidity Safe areas only.
For zone 2 (gas) and zone 22 (dust), ask our team of
experts for the Smart Receiver Ex.
---|---
Power Source
Power supply Input Power supply Output
| ****
127/220V, 50/60Hz
5V DC, 15W
Other
RTC (Real Time Clock) Receiver firmware update Sensor firmware update
| ****
Yes Yes
Yes, when associated with a receiver
Certification
FCC ID IC ID ANATEL IFT
| ****
2BCIS-SR-PRO
31644-SRPRO
06239-23-14488
TRTRSM23-29726
Antenna
Type Model/Manufacturer Peak Gain
| ****
Dipole antenna with SMA connector (50 ohm) ANT-LTE-WS-SMA/TE
4.1 dBi(698 to 803 MHz), 3.4dBi(791 to 960 Mhz),
5.0dBi(1553 to 1609 MHz),5.9 dBi(1710 to 2200 MHz),
3.1 dBi(2300 to 2400 MHz), 4.1(2496 to 2690 MHz)
FCC STATEMENT
Smart Receiver PRO Regulatory Compliance
FCC Class A Information
This device complies with Part 15 FCC Rules. Operation is subject to the
following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation
This equipment has been tested and found to comply with the limits for a Class
A digital device, according to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. The
radiated output power of this device meets the limits of FCC radio frequency
exposure limits. This device should be operated with a minimum separation
distance of 20 cm (8 inches) between the equipment and a person’s body.
ISED Certification
This device complies with ISED Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The radiated output power of this device meets the limits of ISED Canada radio frequency exposure limits. This device should be operated with a minimum separation distance of 30 cm between the equipment
2D Drawing
CONTACT
- get@tractian.com
- 201 17th Street NW, 2nd Floor Atlanta – GA, 30363
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>