ORDA SAMSUNG GALAXY TAB S9 plus User Manual
- August 20, 2024
- ORDA
Table of Contents
ORDA SAMSUNG GALAXY TAB S9 plus
Specifications
- Brand: ORDA
- Model: ORDA
- Website: www.orda-tech.com
- FCC Compliance: Part 15 of FCC Rules
Product Information
The ORDA device is designed to comply with FCC regulations regarding harmful interference and RF exposure. It is a portable device that meets general RF exposure requirements, allowing for unrestricted use in portable conditions.
Pairing Mode
Press and hol simultaneously for 3 seconds to enter into the pairing state.
Bluetooth will exit the pairing state if no connection is made within 3
minutes.
Bluetooth Connection
Go to Tablet’s Settings > Bluetooth to turn it on. Find ” ORDA Keyboard” under
“Available devices” and connect it.
Bluetooth Re-connection
After a successful pairing, the keyboard will automatically pair with your
Tablet in 5 seconds the next time.
Charging Indicator
Auto Sleep
The keyboard backlight will automatically enter sleep mode after 30 seconds of
inactivity, and the keyboard itself will also enter sleep mode after 30
minutes of inactivity. Press any key to wake up the keyboard, and it will
automatically reconnect to your device.
Basic Keyboard Settings
Go to Tablet’s Settings > General management > Physical keyboard
Trackpad Settings On your Tablet,
- Go to Settings > General management > Mouse and trackpad > Adjust pointer speed
- Go to Settings > General management > Mouse and trackpad > Wheel scrolling speed (“Slow” as shown)
A Full Row of Shortcut Keys for Easy Media Control.
Press and hold the right + Shift key, then press the corresponding key to type the character highlighted.
ASSEMBLING AND DISASSEMBLING INSTRUCTIONS
Horizontal Assembling:
Horizontal Disassembling:
TRACKPAD GESTURES FOR SAMSUNG ANDROID (Some of these gestures may not be available in the DEX system)
TROUBLESHOOTING
If the keyboard doesn’t work, please check:
- If it’s powered on, if not, switch it on.
- If its battery has run out, if yes, charge it immediately.
- If the Bluetooth connection fails, turn off the keyboard and restart it after 10 seconds, and the keyboard will reconnect to your device automatically. If the problem still exists, go to Tablet Settings>Connections >Bluetooth>Paired devices>ORDA Keyboard>Unpair. Then reconnect the keyboard according to the previous connection steps.
- If the Bluetooth connection still fails, press for 3 seconds to restore factory settings. Then reconnect the keyboard.
- Or you can restart your Tablet and then check if the keyboard can work normally.
If the keyboard still doesn’t work after trying the above solutions, please try to repeat these steps.If your problems can’t be solved after that, please contact the seller for help.
Friendly Reminder
- The keyboard is built with a rechargeable polymer battery.
- If you’re not going to use the keyboard for a long time, we suggest turning it off to avoid power drain and extend its battery life.
SPECIFICATIONS
- Bluetooth Version: Bluetooth 5.1
- Standard Type-C Port: Supports CTC charging
- Bluetooth Range: 10 meters
- Modulation Methods: GFSK
- Working Voltage: 3.3-4.2 V
- Working Current (Average Typing Speed without Backlight): 2.0 mA
- Standby Current: 0.5 mA
- Sleep Current: 0.01 mA
- Charging Current: 307 mA
- Standby Time: > 1500 h
- Charging Time: 4 h
- Working Current with the Brightest White Backlight: 103 mA
- Continuous Working Time with the Brightest White Backlight: > 8 h
- Auto-sleep Time of the Backlight: 30 s
- Auto-sleep Time of the Keyboard: 30 min (Bluetooth will disconnect during deep sleep mode. Any key can be pressed to wake it up.)
- Lithium Battery Capacity: 800 mAh
- Continuous Working Time Without Backlight: > 320 h
- Life Cycle of the Lithium Battery: 300 times
- Size of the Lithium Battery: 3.3 34 76 mm
- Bluetooth Pairing Name: ORDA Keyboard
COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FAQ
- Q: What should I do if the device causes interference?
- A: If the device causes interference, try adjusting its placement or moving it away from other electronic devices to minimize interference.
- Q: Can I modify the device for better performance?
- A: No, any modifications not approved by the manufacturer could void your authority to operate the equipment. It is recommended to use the device as intended without alterations.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>