Xmenha my N3 Wireless Bluetooth Headset Instruction Manual

Xmenha my N3 Wireless Bluetooth Headset

Dear users: Thank you very much for using this wireless Bluetooth headset, please read the manual carefully before using, the correct operation of this product, so that you can better experience the superior performance of the product.

Product Introduction

Product parameters

• Model
  

  • my N3

• Transmission range
  

  • 10-15m

• Charging case battery
  

  • 350mAh

• Earbuds battery
  

  • 30mAh

• Music Time
  

  • 4Hours

• Calling Time
  

  • 4Hours

• Standby time
  

  • about170hours

• Charging input

  • DC5V2A

Switch machine
The headset is automatically turned on when taken out from the charging compartment.

Wireless Pairing Steps

1. When pairing, please control the distance between the wireless headset and the mobile phone in the range of 1 meter, remove any headset from the charging compartment, and the headset wil automatically turn on and enter the pairing stale
2. Open the phone wireless, search for the pairing name (my N3) operation of the phone to make pairing can be completed with voice prompts
3. If there are two of my N3 pairs at the same time, and the headset is not connected to the phone, Touch the touch point on any headset three times, make the initial pairing of the two headphones, and then follow the (1.2) painting step to pair the headset with the phone.

Functional operation

1. Touch Twice Pause / Play
2. Touch three times the volume plus or minus
3. Touch the voice assistant four times
4. Call Short Press to Answer
5. Call hang up long press 2S
6. Call rejection long press 28

Warm prompt

1. driving when using headphones, please comply with the regulations of the country or region.
2. do not disassemble or modify the headset for any reason, otherwise, it may cause the headset to malfunction or burn out, please send the headset to an authorized repair center for repair.
3. please put the equipment and all accessories in a place where children and pets can not roach, accidentally swallowing small cons may noodle and serious injury.
4. do not put the device at a temperature that is too low or too niche (below 0° C or above 45 ° C) environment extreme environment will lead to the deformation of the novice, reduce ine chare the capacity of the device, ano shorten the service life of the device
5. do not use the equipment in thunderstorms. Thunderstorms can cause equipment to not work properly and increase the risk of electric shock,
6. Listening to high-volume sounds for a long time can damage hearing. Listening to high notes while driving can be distracting and lead to accidents. Use only the minimum volume settings required for calls or music.

FCC Warning Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirements.

Specifications

• Compliance: Part 15 of FCC Rules
• RF Exposure: Meets general requirements

FAQ (Frequently Asked Questions)

Q: What should I do if I want to make changes to the device?
A: If you intend to modify the device in any way, it is crucial to seek explicit approval from the manufacturer to avoid voiding your operating authority.

Q: How can I ensure compliance with FCC rules?
A: Follow the guidelines provided in the user manual regarding FCC compliance, avoiding interference, and accepting received interference.

Q: Is there a specific distance I should maintain from the device for RF exposure?
A: It is recommended to maintain a safe distance between yourself and the device to minimize RF exposure. Refer to the user manual for detailed information.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>