Hangshi MD280 Wireless plus 2.4G Dual mode Mouse User Manual

Hangshi MD280 Wireless plus 2.4G Dual mode Mouse

Product Information

Specifications

• Connected by: Bluetooth & 2.4G receiver
• Dimensions: 122.9877.7678.77mm
• Operating distance: 8 m / 26.2 ft
• Rechargeable lithium battery: 500mAh
• DPI: 800-1200-1600-2400

Product Usage Instructions

Wireless Connection Setup

1. Mouse Re-pairing:
   • Step 1: Turn off the mouse and unplug the 2.4G US receiver.
   • Step 2: Press and hold Left-button, Wheel button, and Right-button for 3 seconds.
   • Step 3: Insert the 2.4G USB receiver into the computer within10 seconds, keeping the mouse close to the receiver within 30cm (0.98 ft).
2. Wir eless Bluetooth Connection:
   • Step 1: Turn on the mouse.
   • Step 2: Click the Connect button to choose Bluetooth 1/2 channel.
   • Step 3: Press and hold the Connect button for 5 seconds to enter pairing mode.
   • Step 4: On your device, search for and connect to “Nulea MD280”.

Sleep Mode
The mouse will enter sleep mode if idle for 30 minutes. Press any key to exit sleep mode.

Charging

1. Step 1: Connect one end of the Type-C cable to a USB charger and the other end to the charging slot on the mouse.
2. Note: Output: DC 5 V / 500mA. USB charger not included.
3. Step 2: The charging indicator will glow blue during charging. A full charge takes approximately 3.5 hours.

FAQ
Q:  How do I know if the mouse is fully charged?
A: The charging indicator will turn off once the mouse is fullycharged.

Wireless+2.4G Dual-mode Mouse

User Manual
Model: MD280

Packing Content

• 1* Dual-mode Wireless Mouse
• 1* 2.4G USB receiver ( For 2.4G connection only )
• 1* Type-C Charging Cable
• 1* User manual

Specification

Product Preview

1. ON/OFF Switch: turns the mouse on and turn off.
2. Connect Switch: 2.4G/bluetooth 1/bluetooth 2 channel switch button.

Mouse re-pairing:

1. Step 1. Turn off the mouse and plug out the 2.4G USB receiver.
2. Step 2. Holding down “Left-button, Wheel button and Right-button” for 3s without loose, and then turn on the mouse.
3. Step 3. Immediately insert the 2.4G USB receiver into the computer within 10s and keep the mouse close to the receiver within 30cm (0.98 ft ).

Wireless Bluetooth Connection

Mouse pairing:

1. Step 1. Turn on the mouse.
2. Step 2. Click the “Connect button” to choose Bluetooth 1/2 channel.
3. Step 3. Hold and press the “Connect button ” for 5s to enter pairing mode.
4. Step 4. On your device, find the name of “Nulea MD280” and click to connect.

Sleep Mode

The mouse will enter sleep mode if idle for 30min.
Press any key to exit sleep mode.

Charging

1. Step 1. Connect one end of the included type-c cable to a USB charger, and connect the opposite end to the charging slot on the keyboard or mouse.
   (Note: Output: DC 5 V / 500mA; USB charger is not included)

2. Step 2. The charging indicator will glow blue while the keyboard or mouse is charging.
   A full charge takes approximately 3.5 hours.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>