COMBIER CMA210S-BX Bidet Toilet Seat Instruction Manual

COMBIER CMA210S-BX Bidet Toilet Seat

• Thank you for your recent purchase of the product.
  Please read the enclosed information to ensure the safe use of your product.

• Be sure to read this Instruction Manual before using your product and keep it in a safe place for future reference.

www.combier-bidet.com
Any question contact: cs@combier-bidet.com

The available functions vary according to the model.

Safety Precautions

These precautions are important for safe usage. Be sure to follow them and use the product correctly.

• This product is classified as Class 1 Equipment and must be grounded.

• Install this equipment where the electrical outlet is accessible.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  Children should be supervised to ensure that they do not play with the appliance.

• Use the new hose set included with this equipment. Do not reuse an old hose set.

WARNING

• Never disassemble, repair or alter.

• Doing so may cause fire, electrical shock. heat or short circuit

• Only qualified service personnel should repair this product

• Do not plug or unplug the power plug with wet hands.

• Doing so may cause electrical shock

• Do not splash water on the main unit or power cord, and do not utilize it in areas of high.

• This can cause a fire or electric shock
  Do not supply electrical power to the product until it is installed on the toilet and the water supply hose is properly connected.

• This can cause a fire or damage the product.

• Please use public water supply.

• Please do not connect the unit to industrial water or greywater.

• This can cause skin infections or urinary tract infections and also damage the unit

• Keep the cord away from cigarettes or flammable substances.

• This can cause electric shock or bodily injury.
  Do not use any power supply other than the one specified.

• AC 110V,60Hz

• Doing so may cause fi re or excessive heat.

• Pull the plug out from the outlet and wipe clean with a dry cloth.

• Always unplug the plug from the outlet before removing the main unit.

• Failure to do so could cause a fi re or electrical shock

• Do not use a damaged power cord or a loosely fitted electric outlet.

• This can cause an electric shock

• When cleaning, do not use cleaning detergents (oxidized products, sink products, toilet cleaning products, and any types of stain removers) on the external surface of the electronic toilet seat.

• This can change the color of the external surface and can also cause problems with the seats functioning

• Do not touch the power plug during thunderstorms.

• Doing so may cause electrical shock

CAUTION

• Do not stand on top of the seat cover, seat or main body unit.
• This can damage or break the unit.
• Do not slam or close the seat or seat cover forcefully.
• This can damage or break the unit.
• Do not do anything that may damage the power cord, power plug.
• Pulling on the cord may cause damage and result in fi re or heat.
• Prevent children from putting foreign substances or inserting their hands into the dryer outlet or onto the nozzle.
• Doing so may cause burns, electrical shock or malfunction.
• Do not let urine contact the dryer outlet or nozzle area.
• When cleaning or not using the product over a long period of time, be sure to unplug the unit.(refer to page )
• Install the Wash let properly according to the Installation.
• Improper installation may result in water leakage, electric shock or fire.

Grounding Instructions

• This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electrical current.
• The plug must be plugged into an outlet that is properly installed and grounded. it DANGER – Improper use of the grounding plug can result in a risk of electric shock.
• If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat-head terminal.
• Check with a qualified electrician or serviceman if the grounding wire instructions are not completely understood, or if in doubt as to whether the product is properly grounded.
• This product is factory equipped with a speci fie electric cord and plug to permit connection to a proper electric circuit. Make sure that the product is connected to an outlet having the same configuration as the plug.
• No adapter should be used with this product. Do not modify the plug provided – if it will not fit in the outlet, have the proper outlet installed by a quali tied electrician.
• If the product must be reconnected for use on a different type of electric circuit, the reconnection should be made by quali fied service personnel.
• If it is necessary to use an extension cord, use only a three wire extension cord that has a three blade grounding plug, and a three-slot receptacle outlet that will accept the plug on the product.
• Replace or repair a damaged cord.

Parts Names

Knob + remote control sample diagram
(Product functions shall be subject to physical objects)

Preparation

Insert the battery

1. Remove the remote control from the hanger.
2. Open the battery cover and insert two AA batteries.
   • Always purchase the correct size and grade of battery most suitable for the intended use.
   • Remove batteries frome equipment which is not to be used for an extended period of time.
   • Remove and replace all batteries.
3. Mount the remote control in the hanger.

About the remote control

• Select a convenient spot near the toilet to attach the remote control holder.
• Make sure that the selected spot will not be exposed to water and the area where you intend to affix the holder is clean and dry.
• Remove film from the double sided tape locaed on the back of the remote control holder and place the holder in the selected area.

1. Turn on the power
   Insert the power plug.
   The wand extends and then retracts.

2. Open the shutoff valve
   Fully open the shutoff valve.

Control Designations

Remote control sample diagram
(Product functions shall be subject to physical objects)

PAIR CODE

1. Cut the power.
2. Keep pressing” Bidet Wash”/Move”key till all indicators of remote is flashing.
3. Turn on the power. After nozzle has reset the light of the remote stop blinking.code done.

RECESSIVE FUNCTION
What need to be kept pressing written in the brackets are recessive functions.

Basic operation

Caution Please press the’off’ or low button for seat temperature when the following persons use it.
Special precautions should be taken for children, those who cannot adjust the temperature, and those who have sensitive skin.

Sit on the seat.
Always sit on the middle of the unit and do not sit on the side of the seat.
(The basic functions will not work if the skin sensor is not active.)

Warning

• Do not press the control knob harder than needed. This can cause damage,
• The skin sensor of the seat is only activated with bodily contact, please be sure to pull down your clothes amply and do not cover the seat with any clothing items, as it can prevent the seat from activating.

Simple Control Knob

• Power key Keep pressing middle button to turn on/off power.
• Bidet wash/move Rotate counterclockwise to enable the Bidet wash function
• Drying/Flush Press the control knob lightly to activate the warm air drying function.
• Rear wash/move Turn it clockwise to enable the rear wash function
• Stop If you press the button during use, the operation will stop

The wand can be automatically cleaned when you use the cleansing functions (Rear wash, Bidet wash, etc,)

Automatic Functions

As you move away
How to disable or enable the auto-open lid feature of CMA210S-BX?

• Press and hold “Turbo Wash” button on the remote control to disable or enable the automatic lid opening function.
  What is the sensing distance for the CMA210S-BX to automatically open the lid when detecting a human body?

• If necessary, Long press and hold “Strength- & Strength+” to adjust the sensing distance. You can choose from 5 levels, each level has a distance of approximately 11.8in/30cm.

Detailed Operation

Rear Wash/Move
Press this button to run rear washing.
The washing will stop it self in about 90 seconds.
Press this button while rear washing is running, the nozzle will be at the fixed position.
Press water pressure button to adjust the strength of spray while this function is running.

Bidet Wash/Move
Press this button to run bidet washing.
The washing will stop itself in about 90 seconds.
Press this button while rear washing is running, the nozzle will be at the fixed position.
Press water pressure button to adjust the strength of spray while this function is running.

Drying
Press this button to run Drying .
The drying will stop itself in about 5 minutes.
Press” drying temp”button while drying is running, The wind temperature changes from high to low. can be adjusted as you like.

Auto/Mode
Press this button and the automatic function will run step by step, from washing to drying.

Kids/Mode
Press this button to run washing, move washing, drying, water pressure strength is medium, drying temperature is medium.When convenient for children, it can be operated independently of seat ring sensing

Turbo Wash
Press this button to run turbo wash.
The water pressure of rear spray will be highest level.

ECO/Mode
Press this button without people seating on cover to run energy saving mode, seat ring temperature off, maximum power saving.
Reset to original settings in 8 hours.
Reset to original settings after someone is seated.

Lighting
Press this button to turn on/off nighe light.

Strength(Clean Strength)
Press this button to adjust water pressure.
Can be adjusted as you like.
There are 5 levels. (low-high).

Forward/Cover Lid

When using the cleaning function, this key is the wand forward function. The wand can be adjusted 2 levels forward.
When no one is sitting, Press this button to open/close cover lid.( CMA210S- BX)
(Adjust the strength of cover lid opening by” Strength”key +,-after keep pressing” Cover Lid” key in about 3 seconds till the”GD “is showed out. GO clamps the least, G9 clamps the most.)

Backward/Seat Cover
When using the cleaning function, this key is the wand backward function. The wand can be adjusted 2 levels backward.
When no one is sitting, Press this button to open/close seat cover.( CMA21 OS- BX)
Adjust the strength of cover lid opening by ” Strength” key(+,-)after keep pressmg”Cover Lid” key in about 3 seconds till the”SD “is showed out. SO clamps the least,S9 clamps the most.)

Stop/Power
Press this button while using to stop running.
The product will also stop running while people get up from toilet.(Except when enabling kids mode functions)
Press this button to stop function for washing or drying.
Kepp pressing to turn on/off power.

Water Temp
Press this button to adjust water temperature to your preference. The water temperature is adjustable in 4 levels. According to the use environment, the actual water temperature is about93.2°F(34°CH04°F(40°C),

Drying Temp
While the dryer function is operating, press ‘Dry temp’ to adjust the drying temperature. There are 5 levels to adjust.

Seat Temp
Press this button to adjust seat temperature to your preference. The seat temperature is adjustable in 4 levels. According to the use environment, the actual seat temperature is about 89.6°F(32°C)-100.4°F(38°C).
Remarks : With long seat reminder function, the machine will give an alarm sound after 15 minutes to remind you to leave the seat.

Maintenance

WARNING
Always disconnect the power plug from the outlet before cleaning, maintenance or inspection. (see left)
(Failure to do so may cause electric shock or malfunction, resulting in a breakdown.)

Wand cleaning method

1. When no one is seated, press the rear wash/bidet wash cleaning spray rod out for nozzle or nozzle cleaning.
2. Remove the nozzle, clean it with a toothbrush or a soft cloth, install the nozzle back to the original position after cleaning, press the stop button, and return the spray rod to its original position.
3. Note: Do not reset the nozzle when it is pulled out, which may cause failure

Main Unit (Approximately daily)

1. Unplug the power plug.

2. Wipe with a soft cloth that has been soaked in water and wrung-out thoroughly.
   For heavy dirt
   Wipe with a soft cloth soaked in diluted, neutral kitchen detergent, and then wipe with a soft cloth soaked in water.

3. Insert the power plug.
   The “Power” LED lights up.

Maintenance

Gap between the Main Unit and Toilet Bowl (Perform monthly)
You can remove the main unit to clean the top of the toilet bowl and the bottom of the main unit.

1. Unplug the power plug.

2. Remove the main unit.
   Do not pull the unit with undue force (because the water supply hose and power cord are attached).

3. Clean the gap.
   Wipe with a soft cloth soaked in a diluted, neutral kitchen detergent. Then, wipe it with a soft cloth soaked in water so that no detergent remains.

4. Mount the main unit.

5. Insert the power plug.

Troubleshooting

Confirm items before applying for maintenance

1s turned on, and that the light is on

Remove and reinsert the power plug

Flushing does not produce water or water is not smooth

| Whether the filter rod is too dark yellow or blocked due to impurities|

Replacement filter rod

Whether the water supply is off or the water supply valve is off| Check the water source.Open the water supply valve
Whether the nozzle is blocked by scale| Please clean the nozzle with a toothbrush
Water leakage| Whether the connection of the water supply pipe is tightened| Please tighten the connection part of the water supply pipe
The water temperature and seat ring are cool| Whether the water temperature and ring temperature are adjusted to normal temperature|

Please readjust the temperature

Fault display description (knob + digital tube)

Fault description| Digital tube| knob| Indicator light| remarks
---|---|---|---|---
The seat temperature sensor is abnormal| E1| Blue light flashing| Seat temperature and low temperature flicker|
Excessive seat ternperature| E2| Red light flashing| Seat temperature high temperature flicker|
Fan anomaly| ES| Green light flashing| Set temperature flicker in temperature|
Abnormal water

temperature sensor

| E6| Yellow light flashing| Water temperature and low temperature scintillation|
The water temperature is too high and the water shortage is dry| E7| Purple light fl cker|

Water temperature scintillation

|
There is water flow but no heatin9, water heating circuit 1s abnormal|

E8

| Cyan light flicker| The water temperature flickers at medium temperature|
When any of the above fault alarms occur, except abnormal seat temperature(E1/E2), the alarm can be automat cally restored. In other abnormal cases, the alarm can be lifted only after power off and restart.

Specifications

Technical parameter|

110V ~ 60Hz

Maximum power of the machine :1350W

Rated power: 11SOW (Rated power test conditions: influent temperature is 15±1°C, ambient temperature is 20±5°C, measured

under the highest clean ng temperature,Cleaning pressure and seat ring heating temperature.)

---|---

Water supply

| mode| Directly connected with water mains
Service pressure| Minimum pressure 0.08Mpa­ maximum pressure 0.75Mpa

Cleaning device

| Rear washing water volume| 0.69L/min
Bidet washing water volume| 0.72L/min
Temperature regulation| Normal temperature – high temperature about102.2°F(39°C)
Heating power| 1300W(Max)
Safety device| Temperature switch, water temperature sensor, temperature fuse

Seat ring heating device

| Temperature regulation| Normal temperature – high temperature about 100.4°F(38°()
Heating power| 35W(Max)
Safety device| Temperature control switch, temperature fuse, seat temperature sensor

Warm air drying device

| Temperature regulation| Normal temperature – high temperature about131°F(SS0C)
Heating power| 200W(Max)
Safety device| Temperature control switch, temperature fuse
Other safety devices| Leakage protector
Power cord length| l.Sm

Product specification

|

References

• 欢迎?????? | 敖武的博客

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>