Beemoo Reform ISOFIX Booster Seat Instruction Manual

Beemoo Reform ISOFIX Booster Seat

IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

Model: Beemoo Reform
i-Size Car Seat

I-Size Booster Seat Instructions
Suitable for children from 100cm to 150cm (approx 4 to 12 years old)
Universal car seat with two installing methods: seat belt installing, and seat belt plus additional ISOFIX connector.

Notices

1. The child car seat must only be used in vehicles fitted with a three-point seat belt system approved by regulation ECE-16 or similar.
2. A correct fit is likely if the vehicle manufacturer has declared in the vehicle handbook that the vehicle can accept a ‘Universal’ child restraint for this group.
3. The child car seat conforms to regulation ECE-R129/03 for general use in vehicles.
4. Child car seats can mark vehicle seat upholstery; the manufacturer is not responsible for damage to vehicle seats.
5. This child car seat has been declared ‘Universal’ under more stringent conditions than those applied to earlier designs, which do not carry the ‘Universal’ mark.
6. Situations like unauthorized modifications, changes of use, or failure to fit the child car seat according to instructions could void the warranty.
7. Keep this manual safe for future reference.
8. Keep proof of purchase.
9. All pictures shown are for illustration purpose only. Actual product may vary due to product enhancement.

WARNINGS

• Read carefully before attempting to fit the child car seat.
• Never leave your child unattended. Your child’s safety is your responsibility.
• Child car seat must be fitted according to the manufacturer’s instructions. Incorrect installation could be dangerous.
• Installation should only be performed by a competent adult.
• Always ensure that new or occasional users have read and understood the instructions.
• Keep this instruction manual with the child car seat.
• Do not fit the child car seat on a side or rear-facing vehicle seat.
• Ensure the passenger seat is locked in the upright position before installing the child car seat.
• Do not use the child car seat at home; it is designed for use in the car.
• Do not leave loose objects on the back seat that may be dangerous during sudden braking.
• Make sure rigid items and plastic parts do not become trapped in doors or movable seat units.
• Always use the child safety lock system if available, to make it impossible for the child to open the car doors from inside.
• Allow the child a break during long car journeys.
• Ensure that the child car seat is always secured to the car seat, even when not in use.
• Do not use the child car seat without its original cover.
• Stop the car at regular intervals to check the position of the child car seat and the seat belt.
• In the event of an emergency, it is crucial to be able to release the child quickly, as defined by British Standards. The seat buckle cannot be fully tamper-proof, so actively discourage your child from playing with or using the buckle.
• If traveling with passengers using both front and rear passenger seats, place lighter occupants in the rear and heavier occupants in the front.
• If you have no option but to place your child car seat on a rear passenger seat next to side airbags:
• Consult your vehicle manufacturer for side airbag details; it may not be safe.
• Ensure your child does not lean into the area immediately around the airbag.
• Do not place anything under the child car seat (e.g., a towel or cushion) as it could affect the seat’s performance in an accident.
• Avoid winter clothing bundling, as bulky clothing can lead to incorrect harness tightening. In an accident, the child can slip out of the extra padding. Let the car warm up or cool down before placing your child in there. If your child is cold, place a blanket over the top of the harness.
• In the event of an emergency, it is important to be able to release the child quickly. Discourage your child from playing with or using the buckle.
• Ensure that the lap section of the seat belt is worn low down, engaging the pelvis firmly.
• Make sure all passengers in the vehicle have their seat belts fastened.
• Never use a seat belt routing scheme different from the instructions.
• Lap and diagonal seat belt (and harness if fitted) must be used at all times when your child is in the child car seat.
• Make sure there are no twists in the seat belt.
• Don’t leave your child in the child car seat parked in direct sunlight or on a hot day.
• Avoid prolonged direct sunlight exposure to the child car seat. Cover the child car seat with a sheet when not in use to reduce exposure.
• Ensure the child car seat is as close as possible to the backrest of the car seat.
• Remove the headrest of the passenger seat if it obstructs the proper installation.
• The manufacturer only guarantees this product then the original owner uses it.
• You MUST replace the child car seat and your vehicles seat belts if they become badly worn or damaged.
• You MUST replace or send the car seat to the manufacturer for inspection (together with an incident report) if the car seat has been involved in an accident as it may have unseen damage and may not protect your child as well as it should.

Important Reminders:
Ensure your child knows the seat is there to keep them safe.
Do not start the engine until you are sure that your child is securely harnessed in their seat and that you have correctly fastened your seat belt.

PART LIST

1. Headrest
2. Side
3. Armrest
4. Recline button
5. Adjustment handle for the headrest and sides
6. Upper belt guide
7. Side protection system
8. Lower belt guide
9. ISOFIX connector
10. ISOFIX release button
11. ISOFIX slide lever
12. Instruction Storage (under base)
13. Extendable Leg Support

ASSEMBLY & FUNCTIONS

Positioning the seat

• The child car seat can only be used with an automatic 3-point safety belt and NOT with a 2-point lap belt.
• The child car seat can be secured in a forward-facing position in the rear seats using existing seat belts.
  WARNING : Never use in a seat with an active airbag.

Installation with the vehicle’s seat belt
The child is secured with the car’s safety belt.

Installation with the vehicle’s seat belt and ISOFIX connector
The Child car seat is secured to the vehicle with the two rear ISOFIX connectors.

Securing your child in the Car Seat and Installing the Child Car Seat

1. Place your child in the car seat and ensure they are sitting well back.

2. Thread the vehicle’s seat belt through the belt guide under the headrest and the belt guide under the armrest next to the seat belt buckle.
   Ensure that no part of the seat belt has become twisted or trapped and that the car seat’s fabric cover is not impending the movement or correct fitting of the seat belt.

3. Ensure the diagonal belt lies gently on the child’s shoulder, and the lap belt is worn over the hips. Tighten the diagonal section of the seat belt by pulling it upwards until there is no slack and the belt holds the child firmly in place.

4. To take the child out of the seat, unfasten the seat belt and undo the shoulder belt guide.

Safest seat to fit your child car seat to:

• If your center rear passenger seat has a three-point seat belt system, use it.
• If the center rear passenger seat lacks a three-point seat belt system, use the rear left or rear right passenger seat.
• The front passenger seat can only be used if it DOES NOT have an airbag and IS fitted with a three-point seat belt.

EXTREME HAZARD: NEVER USE IN ANY PASSENGER SEATS EQUIPPED WITH AIRBAGS (SRS)
Consult the car manufacturer for suitability, as children’s bodies cannot withstand the forces exerted by deploying airbags.

Using the ISOFIX System if Your Vehicle Has Additional ISOFIX Anchor

• If your vehicle has ISOFIX anchor points, ALWAYS use them for a more stable installation.
• Match the backrest hook to the rear side of the base.
• Place the car seat in the appropriate position on the vehicle’s seat, facing in the direction of travel.
• Rotate the adjuster button in anti-dockwise direction, and simultaneously pull the ISOFIX connectors outwards as far as it goes- make sure it cannot be pushed backwards.

Match the ISOFIX connectors to the vehicle’s anchoring point until you hear a ‘click.’ Then rotate the adjuster button in anti-dock wise direction, and simultaneously push the seat against the vehicle to eliminate the gap between car seat and vehicle’s seat.

ATTENTION: ISOFIX connectors are an additional fitting system for securing the car seat and not suitable for securing a child. Child MUST ALWAYS be secured with the car’s three-point safety belt.

Adjusting the Headrest Height

• Pull upwards on the button behind the headrest to adjust its height.
• Release the button when the headrest reaches the desired height. You should hear a ‘click’.

To ensure the best protection for your child, the shoulder belt must be guided so that is passes gently over the child’s shoulder. You will need to adjust the position as the child grows.

Removing the Child Car Seat

Pull the grey button backward on the ISOFIX anchors to release the car seat from the vehicle’s ISOFIX anchor points.
Note! If you have difficulty to release the ISOFIX connectors, try to give more force to the car seat against the vehicle’s seat and simultaneously pull the grey button backwards on the ISOFIX connectors to release the car seat. If this does not help- please consult the manufacturer.

Removing and Replacing the Seat Cover

A Remove the headrest covers by pulling the cover forward and up.
B Remove the wings and base my pulling the cover forward and off.

To put the cover back on- follow the same process in reverse and fit the parts into the slots for the sides.

CARE AND MAINTENANCE

• Store the child car seat in a safe and dry environment when not in use.
• Do not store the child car seat near a direct heat source.
• Do not place heavy objects on top of it.
• The seat covers are easily removed and can be wash with a pH-neutral soap and cold water.
• Do not press, iron, dry clean, tumble dry or wring the covers.
• Do not use solvents, caustic, or abrasive cleaning materials.
• Dry the covers flat and away from direct heat and sunlight.
• Wipe plastic/metal parts with a mild soap and warm water.
• You must not remove, oil or lubricate any part.
• Regularly check the child car seat for wear and tear.
• Check the adjustable parts of the child car seat at intervals of about 6 months to ensure it is still correct for your growing child.
• The child car seat may have a slight rattle when not in use, this is normal. It in any doubt – please contact us immediately.

Thank you for choosing our product. If you have any queries or need replacement parts, please contact the manufacturer.

APPROVED CARS (P67-P83)

The child car seat can be installed forward-facing using the ISOFIX anchorage in a vehicle equipped with ISOFIX anchorage points, in combination with a 3-point belt, approved to UN/ECE Regulation No.16 or other standards. When ISOFIX anchorage is not available in the vehicle position, the car seat can be installed forward-facing with a 3-point belt, also approved to UN/ECE Regulation No.16 or other standards.
This car seat is approved for stature height 100 cm – 150 cm. In the forward- facing direction, it may not fit all seating positions at a stature of 135 cm.

ATTENTION! Ensure that your child must always be secured with a 3-point car belt when lower anchorages are used.

Car seat positions marked with * can have a storage compartment in front of the seat. ISOFIX anchorage in the passenger seat (position 1) is normally offered as an option, so depending on the model, this position can be available or not.

We recommend installing this car seat in all vehicle seat positions intended to be used. Check the installation, available space in the vehicle, and the position of the child to verify if this car seat is acceptable for your situation. This list is always in revision. Please also check your vehicle manual specifications.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>