Contardi Clara Portable Outdoor LED Floor Lamp Instruction Manual

Contardi Clara Portable Outdoor LED Floor Lamp

Product Specifications

• Product Name: Clara SMALL Lamp
• Power Supply: USB cable type C (not included)
• Minimum Power Requirement: 2A – 5V
• Battery Type: Lithium (Li-Ion) with PCM protector

Assembly Instructions:

1. Lift the lamp and insert the magnetic light bulb from below, then attach it.
2. Rotate the lighting body counterclockwise to switch between positions:
   • Position 0: Attach and extract the lighting body
   • Position 1: Lighting body turned off (OFF)
   • Position 2: Lighting body turned on (ON)
3. To disassemble, rotate the lighting body clockwise to position 0, then unhook it by pulling downwards.

Recharging Instructions:

To recharge the lamp:

1. Insert the USB cable type C into the light body.
2. Connect the cable to a power supply (not included) and plug it into a socket.

WARNING! It is crucial to fully charge the lithium batteries for at least 10-12 hours on first use. Subsequent recharges should also last a minimum of 4-5 hours to maintain battery efficiency and longevity.

Frequently Asked Questions:

• Q: Can I use a different power supply for recharging?
  A: No, it is recommended to use a USB charger with a minimum power output of 2A – 5V for recharging.

• Q: How do I know when the batteries are fully charged?
  A: When recharging, a full charge indicator may be present on the lamp or the USB cable itself. Additionally, you can refer to the user manual for specific charging indications.

ALL OPERATIONS MUST BE CARRIED OUT BY QUALIFIED PERSON

ASSEMBLY

1. Lift the lamp.
   Put the magnetic light bulb in from below and attach it.

HOW TO USE

The lighting body can be placed in three positions:

• Position 0: to attach and extract the lighting body
• Position 1: lighting body turned off (OFF)
• Position 2: lighting body turned on (ON)

Positions 1 and 2 are obtained by rotatingthe lighting body counterclockwise (starting from position 0 as hooked):

• First step: position 1 (OFF)
• Second step: position 2 (ON).

DISASSEMBLY

• Put the lighting body in position 0 by rotating it clockwise.
• Unhook the lighting body by pulling downwards.

RECHARGING

• USB cable type C supplied Charger adapter not supplied Min power 2A – 5V
• To recharge the lamp insert the USB cable type C in the light body (as shown). Then connect the cable to the power supply and insert it into the socket.

WARNING!
IMPORTANT: the lamp uses lithium (Li-Ion) batteries that mount a protector (PCM) to prevent explosion or fire. At first use it is necessary to fully charge the batteries for at least 10/12h. To maintain the maximum efficiency and duration of lithium batteries – all subsequent recharges must also have a minimum duration of 4/5 hours.

• When the charging cable is correctly inserted, the light is red. The time required for a full charge is 6/7 hours.
• When the light body is fully charged the light turns green.
• When connecting the recharging cable it is possible that both white and red lights will turn on. In this case it is necessary to disconnect the cable and hook the lighting body to the structure, putting it in position 1 OFF. Then unhook the lighting body, putting it in position 0 again, and re-connect the charging cable

ASSEMBLY

1. Rotate the handle 90° anti-clockwise and extract the lighting body.
2. Hook the lighting body magnetic to the extracted part in point 2
3. After turning on the lighting body, reposition it with the handle in the appropriate space, rotating 90° clockwise until it reaches the end of its travel to allow correct locking

HOW TO USE

The lighting body can be placed in three positions:

• Position 0: to attach and extract the lighting body
• Position 1: lighting body turned off (OFF)
• Position 2: lighting body turned on (ON)
• Positions 1 and 2 are obtained by rotating the lighting body counterclockwise (starting from position 0 as hooked):
• First step: position 1 (OFF)
• Second step: position 2 (ON).

DISASSEMBLY

• Put the lighting body in position 0 by rotating it clockwise.
• Unhook the lighting body by pulling downwards

RECHARGING

• USB cable type C supplied Charger adapter not supplied Min power 2A – 5V
• To recharge the lamp insert the USB cable type C in the light body (as shown). Then connect the cable to the power supply and insert it into the socket.

IMPORTANT : the lamp uses lithium (Li-Ion) batteries that mount a protector (PCM) to prevent explosion or fire. At first use it is necessary to fully charge the batteries for at least 10/12h. To maintain the maximum efficiency and duration of lithium batteries – all subsequent recharges must also have a minimum duration of 4/5 hours.

RECHARGING

• When the charging cable is correctly inserted, the light is red. The time required for a full charge is 6/7 hours.
• When the light body is fully charged the light turns gree
• When connecting the recharging cable it is possible that both white and red lights will turn on. In this case it is necessary to disconnect the cable and hook the lighting body to the structure, putting it in position 1 OFF. Then unhook the lighting body, putting it in position 0 again, and re-connect the charging cable

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>