toboli 62831 Telescopic Bicycle Stand User Manual
- June 3, 2024
- toboli
Table of Contents
Operation Manual Telescopic Bicycle Stand
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps, and technical
data can differ insignificantly.
Updating the documentation If you have suggestions for improvement or have found any irregularities, please contact us.
The information contained in this document may alter at any time without previous notice. It is prohibited to copy or spread any parts of this document in any way without prior written allowance. All rights reserved.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible
mistakes in this operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible
efforts to ensure that the operating manual is complete, faultless, and up to
date, mistakes cannot be entirely avoided. If you should find a mistake or
wish to make a suggestion for improvement, we look forward to hearing from
you.
Send an e-mail to: service@wiltec.info
or use our contact form: https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in
our online shop via: https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler Germany
To return orders for exchange, repair, or other purposes, please use the
following address. Attention! To allow for a smooth execution of your
complaint or return, it is important to contact our customer service team
before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15
Introduction
Thank you for purchasing this quality product. To minimise the risk of injury we urge that our clients take some basic safety precautions when using this device. Please read the operation instructions carefully and make sure you have understood its content. Keep these operation instructions safe.
Technical data
| Weight (㎏) | approx. 4.8 |
|---|---|
| Dimensions | Height (adjustable) (㎝) |
| Max. bicycle frames ⌀ (㎜) | 50 |
| Max. load capacity (㎏) | 2 × 20 |
Attention!
Notes preceded by the word “Attention!” warn of possible dangers or dangerous situations. Failure to observe these instructions may result in damage to the product or other objects in the vicinity.
Notice!
Other notes: Useful tip. Serves to facilitate operation or assembly of the
product or for better under- standing.
Scope of delivery
| Part no. | Designation | Quantity |
|---|---|---|
| 1 | Telescopic rod | 1 |
| 2 | Ceiling tile | 1 |
| 3 | Hook rail | 2 |
| 4 | Hook | 4 |
Not pictured
Mounting material
Hexagonal spanner (3 mm and 4 mm).
Mounting material (ceiling)
- 1 × screw (25 × 4.5 mm)
- 1 × washer
- 1 × dowel
Fixing material (floor)
- 2 × screws (50 × 5 mm)
- 2 × washers
- 2 × dowel
Attention!
- After assembly, check that the bike rack is firmly seated between the floor and the ceiling by shaking it slightly! Check all parts of the bike rack before each use! Loose connections must be tightened and defective parts replaced to avoid damage to the product and to ensure proper functioning!
- The bicycle stand must not be used by children, but only by adults who can easily lift the weight of the bicycles!
Attention!
- Only mount the bicycle stand at a 90° angle to the floor and ceiling and only on a firm and level surface!
- Improper or incorrect use may result in danger to persons or damage to the bicycles, the bicycle stand, or other objects in the vicinity.
- Do not hang onto the bike mount and do not try to climb on it!
Assembly
Step 1
Determine a place where you can place the bicycle stand on a firm and level
surface.
Notice!
Before assembling the bicycle stand, lay out all the parts supplied and check
them for completeness using these instructions.
Step 2 (optional)
Fix the ceiling plate (2) to the ceiling with the supplied screw, washer, and
dowel.
Step 3
Position the telescopic rod vertically under the fixed ceiling plate and
extend the rod as far as possible between the ceiling and the floor. The
spring must fit exactly into the ceiling plate.
Notice!
First tighten the quick-release screw firmly by turning the quick-release
lever by hand. Then fix both quick-release screws by closing the lever to
ensure that the telescopic pole (1) is held firmly in place.
Step 4
Now turn the large plastic screw at the base of the bar clockwise. This gives
the bicycle stand additional strength.
Step 5 (optional)
Secure the base plate of the tube to the floor using the screws, washers and
dowels provided.
Step 6
Tighten all the nuts on the bicycle stand using the hexagonal spanner provided
so that the individual parts do not slip or shift.
Notice!
Step 6
is necessary and must be followed in any case!
Step 7
When the tube is fully assembled and tightened, you can attach the two hook
rails (3). Adjust them to the height of your bicycles!
Step 8
You can now attach the four individual hooks (4) to the rails and hang your
bicycles to save space.
Maintenance, care, and storage
- Check all components of the bicycle stand and all screws regularly for tightness. Clean the bicycle stand only with warm water and pH-neutral soap.
- Then wipe it with a dry cloth. Avoid aggressive chemicals (e.g., solvents).
- Store the bike mount in a dry and well-ventilated place.
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in
part, of this instruction manual require the written permission of WilTec
Wildanger Technik GmbH.
© by WilTec Wildanger Technik GmbH
http://www.toboli.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>