toboli 63044 Weight Bench, Barbell Rack User Manual

: October 30, 2023
: toboli

Table of Contents

63044 Weight Bench, Barbell Rack
User’s manual Weight Bench/Barbell Rack
Introduction
Assembly
Step 1
Safety instructions
Scope of delivery
Product Assembly
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

63044 Weight Bench, Barbell Rack

toboli-63044-Weight-Bench-Barbell-Rack-PRODUCT-IMAGE

User’s manual Weight Bench/Barbell Rack

Model: 63044

Illustration similar, may vary depending on model

Please read and follow the operating instructions and safety information prior to initial operation. Technical changes reserved! Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further developments.

If you have any questions or concerns, please contact us at service@wiltec.info, or use our contact form.

The most recent version of this manual in several languages can be found in our online shop: https://www.wiltec.de/docsearch

Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany

Introduction

Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to always take some basic safety precautions when using this product. Please read this operating manual carefully and make sure that you understand it. Keep these operation instructions in a safe place.

Safety instructions
Please read the safety instructions carefully before using the product to avoid injury.

Scope of delivery
The following parts are included in the package:

Back rest (A)
Seat (B)
Barbell bracket (C)
Main rod (D)
Front support (E)
Side bent training bar (F)
Short bar (with foam cap) (G)
Long bar (with foam cap) (H)
Back rest lever (I)
Connection rod (J)
Front bent training bar (K)
Back rest support bar (L)
Support bar (M)
Adjustment lever (with foam cap) (N)
Small foam caps (O)
Large foam caps (P)
Spring clamp handle (Q)
Grip lever (R)
Knob bolt (T)
Barbell clamp (U)
Connecting piece (V)
Ring pin (W)

Assembly

Please follow the assembly instructions carefully to ensure proper assembly of the product.

Step 1

With screws (4), connect the barbell bracket (C) and connection rod (J).
Note: Pay attention to the correct orientation of the base of the barbell bracket (arrows).

Step 2

Connect the main rod (D) with the connection rod (step 1) using the knob bolt (T) and screws (3).
Connect the main rod (D) with the front support (E) using screws (5). Pay attention to the correct orientation of the front support (E) (arrow).

Step 3
Connect the main rod and front support with the support bar (M) using screws (6) and screws (7).

Step 4

Connect the front bent training bar (K) with the front support using screws (2).
Slide the small lever (with foam) (G) through the hole (see fig.) and cover the ends of the small lever (G) using a small foam cap (O) on either end.

Step 5

Attach the side bent training bars (F) to the barbell brackets using screws (1).
Pay attention to the correct orientation of the F bar (arrow).
Insert the handles (R) and the grip levers (S) into the large holes of the side bent training bars and fix them using screws (7).
Slide one small foam cap (O) on either grip lever (S).

Step 6
Place the seat (B) onto the main rod and attach it using screws (9).

Step 7
Insert the back rest lever (I) through the corresponding holes of the barbell brackets (see fig.).

Step 8
The product is now assembled and ready for use.

The information contained in this document may alter at any time without prior notice. No part of this document may be copied or otherwise duplicated without prior written consent. All rights reserved. WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating manual, nor in the diagrams and illustrations shown.

Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating manual is complete, accurate, and up-to-date, errors cannot be ruled out entirely.
If you have found an error or wish to suggest an improvement, we look forward to hearing from you. Send us an e-mail to: service@wiltec.info

or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop: https://www.wiltec.de/docsearch

Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler – Germany

To return your goods for exchange, repair, or other purposes, please use the following address. Atten-tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team before returning your goods.

Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler – Germany

E-mail: service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15

Introduction

Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to always take some basic safety precautions when using this product. Please read this operating manual carefully and make sure that you understand it.
Keep these operation instructions in a safe place.

Safety instructions

Before assembling and using the device, read the user’s manual entirely. The use of the device will only be safe and effective if the device is assembled, maintained, and used properly. It is your responsibility to make sure that all persons using the device have previously been informed about the warnings and precaution measures.
Before beginning a training programme, you should seek advice from your doctor to determine if there are physical or health reasons that would compromise your safety or the proper use of the device. Seeking medical advice is necessary if you take medicine that controls your heart rate, blood pressure, or cholesterol level.
Pay attention to the signs that your body gives you. Improper or excessive training might be harmful for your health. Stop training in case you remark one of the following symptoms: pain, tightness in the chest, irregular heartbeat, extreme shortness of breath, numbness, dizziness, qualmishness. In that case, seek advice from your doctor before continuing your training pro-gramme.
Keep children and domestic animals away from the device. The device may only be used by adults.
Place the device onto a solid and flat surface and onto a cover sparing your floor or carpet. For safety reasons, there should be a free space of a minimum of 0.5 m around the device.
Before using the device, check if all screws and nuts are well tightened.
The device can only remain safe if it is checked for damages and/or wear and tear on regular basis.
Only use the device according to the intended use. If detecting damaged parts during assembly or check or if hearing unusual noises from the inner parts of the device, stop its use. Do not use the device until the problem is solved.
During the use of the device, do not wear clothes that might limit or prevent your movements.
The device is not suitable for therapeutic use.
When lifting or moving the device, be cautious not to hurt your back. Always apply an appropriate lifting technique and/or seek help.

Scope of delivery

Part 1

Product Assembly

Step 1 toboli-63044-Weight-Bench-Barbell-Rack-04

With screws (4), connect the barbell bracket (C) and connection rod (J).
Note: Pay attention to the correct orientation of the base of the barbell bracket (arrows).

Step 2 toboli-63044-Weight-Bench-Barbell-Rack-05

Connect the main rod (D) with the connection rod (step 1) using the knob bolt (T) and screws (3).
Connect the main rod (D) with the front support (E) using screws (5). Pay attention to the correct orientation of the front support (E) (arrow).

Step 3

toboli-63044-Weight-Bench-Barbell-Rack-06

Connect the main rod and front support with the support bar (M) using screws (6) and screws (7).

Step 4 toboli-63044-Weight-Bench-Barbell-Rack-07 Connect the front bent training bar (K) with the front support using screws (2). Slide the small lever (with foam) (G) through the hole (see fig.) and cover the ends of the small lever (G) using a small foam cap (O) on either end.

Step 5

toboli-63044-Weight-Bench-Barbell-Rack-08

Attach the side bent training bars (F) to the barbell brackets using screws (1). Pay attention to the correct orientation of the F bar (arrow). Insert the handles (R) and the grip levers (S) into the large holes of the side bent training bars and fix them using screws (7). Slide one small foam cap (O) on either grip lever (S).

Step 6 toboli-63044-Weight-Bench-Barbell-Rack-09

Place the seat (B) onto the main rod and attach it using screws (9).

Step 7 toboli-63044-Weight-Bench-Barbell-Rack-10

Insert the back rest lever (I) through the corresponding holes of the barbell brackets (see fig.).

Step 8 toboli-63044-Weight-Bench-Barbell-Rack-11

Fix the back rest support bars (L) to the main rod using screws (10), attach the back rest (A) to the back rest support bars and secure it with screws (8).

Step 9 toboli-63044-Weight-Bench-Barbell-Rack-12

Attach the barbell clamps (U) to the barbell brackets.

Step 10 toboli-63044-Weight-Bench-Barbell-Rack-13

Insert the long bar (with foam cap) (H) into the adjustment lever (N). Then slide one large foam cap (P) on either end of the long bar. Set the entire assembly (H, N, O) into the front support and secure it with the ring pin (W). Finally, set the spring clamps (Q) in as shown.

Important Note:
Reproduction and any commercial use (of parts) of this operating manual, requires a written permission of WilTec Wildanger Technik GmbH.