PEXMOR Foldable 26 Inch Electric bicycle User Manual
- August 16, 2024
- PEXMOR
Table of Contents
PEXMOR Foldable 26 Inch Electric bicycle
Specifications
- Wheel: 26inch
- Motor: 750W
- Battery: 48V 13AH
- Max Speed: 32mph / 51km/h
- Max Torque: 82N.M
- Charging Time: 6.5-7 hours
- Pure Electric Mileage: 75-80km
- Assistant-Mileage: 100-110km
- Weight: 36.2kg
- Max Load: 150kg
- Uphill Capability: 15 degrees
- Waterproof Rating: IP65
Parts List
| Item | Name | Qty. |
|---|---|---|
| A | Main Frame with Motorized Rear Wheel, Brake Disc, Chain, & | |
| Derailleur | 1 |
Assembly Instructions
- Rotate the front fork 180 degrees: Turn around the front fork 180 degrees at left or right side. Make sure the stem is perpendicular to the front fork shoulder.
- Take the steel rod out: Use a 13mm wrench to loosen two screws at both ends of the steel rod at the bottom of the front fork. Then take the steel rod out.
Maintenance
Regularly inspect and tighten all bolts and screws. Keep the chain lubricated and check tire pressure regularly. For detailed maintenance instructions, refer to the user manual.
LCD Instrument Use Instructions
The LCD panel provides various functions and settings for your electric bicycle. Refer to pages 15-23 of the user manual for detailed instructions on its use.
FAQs
Safety FAQ and Solutions
For safety-related questions and suggested solutions, please refer to pages
25-29 of the user manual.
Warning!
· Install and adjust this bicycle ONLY in accordance with these instructions .
Read them completely prior to installation and use. Contact customer service
if any point is unclear.
· ALWAYS obey all applicable local and national laws and regulations while
riding. Do not ride this bicycle in any area prohibited to electric bicycles.
Always wear your helmet and other required protective gear. Always maintain
your reflectors and other required safety equipment.
· Check whether the brakes function well using the brake levers before riding.
Even after power is cut to the motorized wheel, the inertia of the bike will
often require active braking power.
· ALWAYS ensure all fasteners and components are intact and securely tightened
before and after every use.
· DO NOT ride this bicycle if any part is damaged or malfunctions. Repair or
replace worn and broken parts before further use.
· Pay attention to the remaining power before setting out and during use.
Recharge your battery as needed to ensure it never runs out of power at a
moment where you are taken by surprise.
· DO NOT allow children or persons unfamiliar with these instructions to
operate this bicycle without strict supervision.
· DO NOT wear loose footwear or clothing that may become caught in the wheels
or any other moving parts.
· It is recommended that you not ride your bike fast when getting started.
This can be ensured by setting the bike’ s maximum speed limit low until you
are fully familiar with your new electric bike and its controls.
· ALWAYS be alert for people, animals, or any obstacles that may appear in
front of you while riding your bicycle. Be aware that pedestrians and drivers
may not expect the speed or responsiveness of your bike. Adjust your behavior
accordingly. It is advisable to install warning devices to draw their
attention, but always be ready to turn safely out of their way if needed. Do
not focus on the LCD display for extended periods of time while riding.
· NEVER ride at a speed where your stopping distance exceeds your visibility.
We do not recommend that you ride your bicycle at night or in an environment
with poor visibility. If you have an emergency that makes it necessary to do
so, keep your light on and limit your speed appropriately.
· DO NOT get the battery, its charger, or its power cord wet or operate them
with wet hands.
· NEVER use the pedal assist system (PAS) or timed shutoff in any situation,
road condition, or terrain where doing so might impair your control of your
bicycle.
· NEVER adjust 03, 06, or 07 on the LCD display panel. Adjustment of these
parameters should only be made when using the display with other compatible
motorized wheels of differing voltage, diameter, or magnet arrangements. In
any other case, any adjustment of these parameters should be undone
immediately and the original settings restored before any further use of this
bicycle.
· Disconnect the battery from this bicycle before any cleaning, servicing, and
storage.
1
Specifications
Wheel Motor Battery
26inch 750W 48V 13AH
Max speed
32mph /51km/h
Max torque
82N.M
Charging time
6.5-7H
Pure Electric Mileage
75-80km
Assistant-Mileage
100-110km
Weight
36.2kg
Max load
150kg
Uphill
15degree
Waterproof
IP65
Parts List
Item
Name
Qty.
A
Main Frame with Motorized Rear Wheel, Brake Disc, Chain, & Derailleur
1
B
Handlebars with LCD Display Panel
Assembly
1. Rotate the front fork 180 degrees Turn around the front fork 180 degrees
at left or right side. Make sure the stem is perpendicular
to the front fork shoulder.
2. Take the steel rod out. Use 13mm wrench to loose two screws at both ends
of steel rod at the bottom of front fork.Then take
the steel rod out.
5
3. Installing the front wheel. (1) Firstly loosen each nut on the axle of the
front wheel.
(2) Secondly attach the front wheel to the front fork. Center the front wheel
on the front fork leg, put the washer and screws on both ends of the hub in
sequence. Then tighten the screws by 15mm Wrench in a clockwise direction.
6
4. Installing the front brake. Loose the two screws on the left side of the
fork with 4mm hex wrench and make sure the
disc is in the middle of the brake, then use the two screws to tighten the
disc brake in place.
7
5. Installing the handlebar Use 5mm hex wrench to unscrew the top bolt and
remove the cap from the stem of the handlebar.
8
6. Calibrate the disc brake position. After installing the disc brake, it is
necessary to check whether the disc plate is in the
middle position of the disc brake. If the disc is not centered, loosen the
screws that have been fixed and adjust the position of the disc brake until
the disc is completely in the middle of the disc brake before tightening the
screw again.
9
7. Installing the headlight. Remove the washer and screw behind the fork
crown by 10mm wrench, put the headlight
bracket inside, then use 4mm hex wrench and 10mm wrench tighten the washer and
screw.
8. Installing the Pedals (1) Attach the pedals to the crank arms on the
appropriate side, screwing them into place. (2) Tighten their locking nuts
with your 15mm wrench.
10
Note: The two pedals (D) ARE different and should NOT be mixed up. The right
pedal is marked with an R and the left with an L.
9. Installing the rear reflector Use Phillips screwdriver tighten the screws
on the reflector. Make sure it is tightly installed
on the seat tube.
11
10. Installing the Seat 11. Installing the front reflector 12. Installing the
mobile phone support
Use 3mm hex wrench to install the screws on the phone support.
12
13. Inflating the Tires 1. Remove the valve cap on a wheel. 2. Connect the
valve to an appropriate pump. 3. Inflate the tire until it feels firm. For
best results, stop inflation when the pressure reaches 25 psi ( 1.68bars). 4.
Disconnect your pump from the wheel, replacing the valve cap immediately. 5 .
Inflate the other tire following the same steps.
13
Maintenance
Charging the Battery
You can see the remaining power on the battery’s LED power display and the top
left of the LCD display panel. When recharging is necessary: 1. Unlock the
battery by inserting the key and turning counterclockwise. 2. Remove the
battery from the bicycle. 3. Connect the charger (H) to a stable compatible
power source. 4 . Connect the battery to the charger using the provided power
cord (I). The battery’s power indicator light should turn red and charging
should begin. 5. When the light turns green, the battery has been fully
charged. Disconnect the charger first from your power source and then remove
the battery from the charger.
Miscellaneous
· Disconnect the power after each use and prior to any cleaning or other
maintenance. · Check the parts of the bicycle for any looseness, wear, or
damage after use. Tighten, repair,
or replace any problematic parts before further use. · The exterior of the
bicycle can be cleaned with a soft damp cloth. Do not use abrasive or
caustic chemicals. · Lubricate the chain and any moving part using a standard
bike lubricant as needed. · If the bicycle will not be used for an extended
period of time, store in a cool dry place
inaccessible to children.
Battery Maintenance Warm Tips
After receiving the bike should charge it first.
Correct Charging Method · 1. After receiving the electric bike should charge
the battery first.Start first riding after fully charging. · 2. The plugs at
both ends of the charger should be connected to the battery first, and then to
the power supply. · 3. If the green light is displayed after the charger is
connected for the first time , it may be that the power supply is not
connected properly. Try reconnecting, the red light shows that it is charging
normally. · The battery should be charged in time on the day after the battery
is exhausted during the ride on the day; · Make sure to fully charge the
battery every 3 months even in the case of infrequent use.
14
LCD Instrument Use Instructions
Please read the operation manual in detail before using LCD-Instrument. This
manual will guide you to use the instrument correctly to achieve a variety of
vehicle control and vehicle status display functions.
Display YL81C provides a variety of functions to meet the riding needs of
users, including: Battery level indicator Assist level adjustment and
indication (0-3/1-3/0-5/1-5) Speed indicator Walk boost mode Distance
indicator (including trip distance and ODO) Error code indicator Personalized
parameter settings (e.g. wheel diameter, speed limit, etc.) Factory default
parameter recovery function
There are three buttons on the operating unit of display YL81C, i.e., the
on/off button , plus button and minus button .
By pressing and holding the button , the display will start to work and the
working power supply of the controller will be turned on. In the power-on
state, by pressing and holding the button , your e-bike will be powered off.
In the power-off state, the display will no longer use the battery power, and
its leakage current will be less than 1uA.
After the display is turned on, the display will show the real-time speed
(km/h) and the trip distance (km) by default. By pressing the button , the
information displayed will be switched between the trip distance (km) and the
ODO (km). When the TRIP light is on, the trip distance is displayed; when the
ODO light is on, the ODO is displayed.
15
LCD Instrument Use Instructions
Long Press and hold , the electric bicycle enters the walk boost mode. Your
e-bike will run at 6km/h. Release to stop the power output immediately and
restore to the state before walk boost.
The battery level indicator consists of four segments. When the battery is
fully charged, the four segments will be all on. In case of undervoltage, the
last segment of the battery indicator will flash, which means the battery has
to be charged immediately.
When a fault occurs in the electronic control system ofyour e-bike, the
display will automatically indicate the error code in the distance area in the
format of E0**. Detailed definitions of error codes are shown in page 17.
16
LCD Instrument Use Instructions
The personalized parameter setting procedure is as follows:
When the display is ON and the speed shows 0,
(1) Press and hold
simultaneously for more than 2 seconds to enter the personalized
parameter setting interface.
(2) Press / to toggle between the personalized parameter setting interface, and press to
enter the parameter changing state.
(3) Press /
to select the parameter, long press for addition operation, long press
for subtraction operation.
(4) Press to save the parameter settings and return to the personalized
parameter setting interface. (5) Long Press to save the parameter settings and
exit the personalized parameter setting interface. The following options are
available on the personalized parameter setting interface:
01P is the backlight luminance setting. Parameters 1, 2 and 3 are available,
which represent the backlight luminance, 1 for the minimum luminance, 2 for
the standard luminance and 3 for the maximum luminance. Press the button to
enter the parameter modification interface. Press the button / for parameter
selection.
Press the button to save the parameter and return to the selection interface
of general setting options.
17
LCD Instrument Use Instructions
02P is the metric and imperial setting, 00 for metric and 01 for imperial.
Press to enter the parameter changing state. Press the / to select the
parameter and press to save the parameter setting and return to the
personalized parameter setting interface.
03P is the rated voltage setting. The available rated voltage range is: 24V,
36V, 48V,60V. Press to enter the parameter changing state. Press the / to
select the parameter and press to save the parameter setting and return to the
personalized parameter setting interface.
04P is the auto sleep time setting. To save the battery power and reach higher
range, this display will be turned off after it has not been used for a time.
The adjustable range is: 1~60min, 00 means no auto shutdown. The factory
default setting is 10 minutes. Press to enter the parameter changing state.
Press the / to select the parameter and press to save the parameter setting
and return to the personalized parameter setting interface.
05P is the Pedal assist level setting. The available PAS level settings are:
0~3, 1~3. Press to enter the parameter changing state. Press the / to select
the parameter and press to save the parameter setting and return to the
personalized parameter setting interface.
18
LCD Instrument Use Instructions
06P is the wheel diameter setting. The adjustable wheel diameter range is:
1~32inch. Press to enter the parameter changing state. Press the / to select
the parameter and press
to save the parameter setting and return to the personalized parameter setting
interface.
07P is the speed sensor magnet number setting. The adjustable speed sensor
magnet number range is: 1 ~ 255 pcs. Press to enter the parameter changing
state. Press the / to select the parameter and press to save the parameter
setting and return to the personalized parameter setting interface.
08P is the speed limit setting. The adjustable speed limit range is: 1~
100km/h. (The maximum adjustable speed limit varies by different protocols).
Press to enter the parameter changing state. Press the / to select the
parameter and press to save the parameter setting and return to the
personalized parameter setting interface.
09P is the start-up setting. The display can choose the following start modes:
00 zero start, 01non-zero start. Press to enter the parameter changing state.
Press the / to select the parameter and press to save the parameter setting
and return to the personalized parameter setting interface.
19
LCD Instrument Use Instructions
10P is the drive mode setting. The available drive modes are: 00 Pedal assist
only, 01 Electric only, 02 Both Pedal assist and electric. Press to enter the
parameter changing state. Press the / to select the parameter and press to
save the parameter setting and return to the personalized parameter setting
interface.
11P is the pedal assist sensitivity setting. When set to higher numbers, it
will take more crank rotations to activate the motor. On lower numbers, it
will take little crank rotation to activate the motor. The adjustable range
is: 1~24. Press to enter the parameter changing state. Press the / to select
the parameter and press to save the parameter setting and return to the
personalized parameter setting interface.
12P is the Pedal assist strength setting. The Pedal assist strength is the
relative strength of the PWM signal from the controller when start to activate
pedal assist. The adjustable range is 0 ~ 5. 0 is the weakest strength and 5
is the strongest. Press to enter the parameter changing state. Press the / to
select the parameter and press
to save the parameter setting and return to the personalized parameter setting
interface.
13P is the number of pedal assist sensor magnets setting. The adjustable
range: 5- 12 pcs. Press to enter the parameter changing state. Press the / to
select the parameter and press
to save the parameter setting and return to the personalized parameter setting
interface.
20
LCD Instrument Use Instructions
14P is the controller current limit setting. The adjustable range is: 1~50A.
Press to enter the parameter changing state. Press the / to select the
parameter and press
to save the parameter setting and return to the personalized parameter setting
interface.
15P is the battery under voltage setting. The value can be adjusted based on
the current rated voltage. Press to enter the parameter changing state. Press
the / to select the parameter and press to save the parameter setting and
return to the personalized parameter setting interface.
16P is the ODO resets setting. The display can choose the following: 00 non
reset, 01reset. Press to enter the parameter changing state. Press the / to
select the parameter and press
to save the parameter setting and return to the personalized parameter setting
interface.
17P is the 6km/h walk boost setting. The display can choose the following: 00
turn off walk boost function, 01 turn on walk boost function. Press to enter
the parameter changing state. Press the / to select the parameter and press to
save the parameter setting and return to the personalized parameter setting
interface.
21
LCD Instrument Use Instructions
Press to enter the parameter changing state. Press the / to select the
parameter. PSd-y means the power-on password is activated while PSd-n is off.
Press to confirm the mode and enter the state of setting the four digits
power-on password or exit to the personalized parameter setting interface.
In the password setting mode, the adjustable digit will flash. Press the / to
select the parameter and press to save the numbers and go to the next digit
setting. Long press to save the parameter setting and return to the
personalized parameter setting interface after finish setting the four digits
in turn.
dE is the restore factory default parameter settings. dE-Y is to restore
default settings, and dE-N is not to restore. Enter into the main setting
interface and keep the speed at 0, press and hold and simultaneously for 2s to
enter the restore factory default setting interface. Pressing / to toggle to
dE-Y. Then after pressing to confirm the display will show dE-0 for a few
seconds and then automatically start to restore the factory default settings.
The display will automatically exit to setting interface after the
restoration.
The display can record trip odometer and odometer. Trip odometer is not
automatically reset after turning off. The trip odometer needs to be reset
manually. Enter into the main setting interface and keep the speed at 0, press
and hold and simultaneously for 2s to reset the trip odometer. The main
interface will flash during the reset process.
22
LCD Instrument Use Instructions
Please use safely, and do not plug or unplug the display when it is powered
on. Please avoid bumping as far as possible. Please do not alter the
background parameter settings of the display at will, otherwise normal riding
cannot be guaranteed. If the display fails to work normally, it should be
repaired as soon as possible. Due to product upgrades of the Company, part of
the displayed contents or functions of the product you bought may be different
from the manual, depending on the actual model.
23
Bicycle Parts Warranty List
Bicycle parts warranty list
Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
28 29 30 31 32 33
Note
Type
Part name
Unit Quantity
Shelf life
Non quick parts
Frame
Set
1
One Year
Non- wearable parts
Fork
Package
1
One Year
Non- wearable parts
Chain Cover
Package
1
One Year
Non- wearable parts
Seat Post
Package
1
One Year
Non- wearable parts
Handlebar
Piece
1
One Year
Non- wearable parts
Stem
Piece
1
One Year
Quick- wear parts
Grip
Pair
1
Half a year
Non- wearable parts
Rim
Pair
1
One Year
Non- wearable parts
Spoke
Stick
1
One Year
Non- wearable parts
Front Hub
Piece
1
One Year
Non- wearable parts
Rear Hub
Piece
1
One Year
Non- wearable parts
BB Parts
Stick
1
One Year
Non- wearable parts Chain Wheel
Set
1
One Year
Non- wearable parts
Free Wheel
Package
1
One Year
Quick- wear parts
Sticker
Set
1
Half a year
Quick- wear parts Front Brake Line Stick
1
Half a year
Quick- wear parts Rear Brake Line Stick
1
Half a year
Quick- wear parts
Fender
Pair
1
Half a year
Quick- wear parts
Bell
Piece
1
Half a year
Quick- wear parts
Tyre
Piece
2
Half a year
Quick- wear parts
Inner Tyre
Piece
2
Half a year
Quick- wear parts
Pedal
Pair
1
Half a year
Quick- wear parts
Chain
Piece
1
Half a year
Quick- wear parts
Saddle
Piece
1
Half a year
Quick- wear parts
Brake Lever
Pair
1
Half a year
Quick- wear parts
Front Brake
Piece
1
Half a year
Quick- wear parts
Rear Brake
Piece
1
Half a year
Quick- wear parts
Seat Bolt
Set
1
Half a year
Quick- wear parts
Stander
Piece
1
Half a year
Quick- wear parts
Front Reflector
Piece
1
Half a year
Quick- wear parts
Rear Reflector
Piece
1
Half a year
Quick- wear parts Wheel Reflectors
Set
1
Half a year
Electric parts
Set
1
One Year
The warranty is natural wear, except for man-made damage and irresistible
causes. You need to provide broken sample parts, send us photos and videos
with Bike Numbers.
24
FAQ and Suggest Solution
FAQ and Suggest Solution
Question
Battery cannot be charged normally Battery indicator light is abnormal
Suggest Solution
(1) First confirm that the charging method is correct. The correct method to
charge the battery 1 . The plugs at both ends of the charger should be
connected to the battery first, and then to the power supply. 2 . If the green
light is displayed after the charger is connected for the first time , it may
be that the power supply is not connected properly. Try reconnecting, the red
light shows that it is charging normally. 3 .It is normal for the battery
indicator to show 3 green and 1 red when it is fully charged. ( 2) If confirm
that the charging method is correct and battery still won’t charge Provide
video to sellers to judge specific problems: What the video needs to show:
please bring the battery to a brighter space, then plug the charger into the
socket. Take a video of the charging process including the battery and the
charger. Seller need to observe the charger indicator and battery indicator
status. So that judge the specific problem based on how the charger and
battery react when charging
Charger and battery indicator status meaning
( 1) If the indicator light of the charger does not light up – Try plugging in
a separate charger ( without connecting the battery) , observe the indicator
light – If it does not light up, the charger is damaged, and arrange for a
replacement charger;
(2) If the indicator light of the charger is on but the indicator light of the battery is off – You need to measure the voltage of the battery with a multi- meter The normal charging voltage range of 48 V battery should be between 54.6-39V. – If it is lower than 39V, it may be that the battery cannot be charged. It needs to be replaced charged with a charger that starts from 0V. – After fully charged the battery can be charged and used normally
PS:It is normal for the battery indicator to show 3 green and 1 red when it is fully charged.
25
FAQ and Suggest Solution
Question
Fast battery drain
Motor does not work/ abnormal sound PAS mode can’t last Gear Level cannot be
adjusted
Suggest Solution
When the new bike is fully charged the voltage should be 54V It is normal for
the indicator lights to be 3 green and one red after the battery is fully
charged. When you are charging the battery, if the charger already shows a
green light, don’t unplug the charger first. You’ ll need to let it charge for
another hour after the charger already shows a green light to fully charge the
battery. Provide video to sellers to judge specific problems: What the video
needs to show: 1 . Fully charge the battery, then start riding and record the
kilometers displayed on the instrument when you start riding. 2 . Then wait
until the battery power is exhausted, shoot the video again and record the
kilometers displayed on the instrument PS : The battery voltage and cruising
range are related to the number of years of use of the battery
First, you need to confirm whether the wiring is normal. If confirm that there
is no problem with the wiring. Try to
check whether there is a problem with the controller or the handle If any
abnormality is found, provide a video to the seller to explain the problem,
and contact the seller to reissue the corresponding accessories
Open the controller box and check whether the connection between the sensor
and the controller is loose or not in good contact
Electric mountain bike has 3 riding modes 1. Throttle-only mode (motor) :
Switch the display to Level 0, twist the handlebar, and the motor will give
power. PS: In throttle mode, the shift lever cannot be adjusted 2. Pedal-
assist mode (pedal+motor) : As you pedal, switch between different levels
using LCD display ( Level 1~5) . The higher the level is, the faster the bike
will go and more battery power it will cost. 3. Pedal-only mode (turn off
display) : As you pedal, shift gears using bike shifter (Level 1~7).”
26
FAQ and Suggest Solution
Question
Suggest Solution
Instrument display the error code
When the instrument is abnormal and the error code is displayed.
Please refer to the picture for the meaning of the error code and then check
whether the corresponding parts are faulty
Vehicle status code meaning
27
FAQ and Suggest Solution
Question
Suggest Solution 2 different situations when the instrument does not work
( 1) The battery is exhausted and the instrument cannot be turned on – Try
charging the battery and turning the instrument back on
Instrument does not work
( 2) The battery is charged but the instrument cannot be turned
on – The first choice is to rule out whether there is a problem with the
wiring. – If it is confirmed that there is no problem with the wiring, the
instrument may be damaged and needs to be replaced
Instrument shows that the max speed cannot reach the initial value
1 . Confirm whether the battery can be fully charged 2 . Check whether the wheel diameter setting has been changed. PS26-27.5-28 three sizes, each size is not the same speed.
Notice: 1 . The Right Left pedal needs to be rotated clockwise rotated
counterclockwise and installed on the RightLeft crank 2 . When installing for
the first time, be sure to tighten the pedals according to the installation
video to avoid pedal falling or damage.
3 . During riding, please check the pedals regularly. If there are signs of
loosening, please tighten them in time to avoid damage to the parts.
Installation and Care of Pedals Notice
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>