echoRO Water Filter Machine User Manual

: August 9, 2024
: echoRO

Table of Contents

echoRO Water Filter Machine
Specifications
Product Usage Instructions
SAFETY INSTRUCTIONS
HOW TO INSTALL THE ECHO ROM SYSTEM
INSTALL DRAIN CLAMP
Final Steps
FIRST-USE INSTRUCTIONS
FILTER CARTRIDGE REPLACEMENT
HOW TO REPLACE CARTRIDGES
FILTER RESET AFTER REPLACEMENT
TROUBLESHOOTING
PRODUCT SPECIFICATIONS
SAFETY PRECAUTIONS
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

echoRO Water Filter Machine

Specifications

Filter Cartridges: Spun PP, Carbon Block, Reverse Osmosis (RO), Membrane Post Activated Carbon Filter (T-33)
Package Contents: Echo ROTM Filter Cartridges, Accessory Box, T-Valve, User Manual, Tubing, Quick Connect Locking Clips

Product Usage Instructions

Safety Instructions
Follow these safety instructions to prevent injury or product damage:

Use a surge protector to avoid voiding the warranty.
Only use the provided power supply and adapter.
Replace cartridges as indicated by the filter life indicator.
When changing cartridges, shut off the source water, release water pressure, and unplug the power adapter.
Avoid storage or usage in temperatures below 0°C/32°F.

Storage Instructions

If not in use for an extended period:

Turn off the source water T-valve to prevent pressure surges.
For long-term storage, turn off the source water valve and unplug the power adapter.

Installation Instructions:
Refer to the Echo RO FaucetTM installation guide included in the box.

SAFETY INSTRUCTIONS

Please be sure to follow these instructions to prevent electric shock, fire, or explosion which could result in personal injury or product damage

ALWAYS REMEMBER

To use a surge protector or warranty is voided
To only use the provided power supply
- Only use the power adapter that came with the Echo RO
To only use manufacturer-certified replacement parts and charging cables.
- Replace Cartridges according to the filter life indicator\
When changing filter cartridges, shut off source water and release water pressure by opening the faucet
Unplug the power adapter and turn off the source water valve for long-term storage
Do not store or use in an environment of 0 degrees C/32 degrees F or below
Handle with care when moving or uninstalling
When the Echo RO is not going to be in use for an extended period (overnight, when the user is on vacation, etc) turn off the source water T-valve to avoid a pressure surge that may cause leaks or damage to housings and filters. Echo Technologies is not responsible for damage caused by this phenomenon
If issues occur, turn off the power and source water. Check the troubleshooting guide (below) and contact Customer Experience for further assistance.

ECHO RO™ PACKAGE

CONTENTS
- Echo RO™ Filter Cartridges
- Spun PP Filter (PP)
- Carbon Block Filter (CTO)
- Reverse Osmosis (RO)
- Membrane Post Activated Carbon Filter (T-33)

Echo RO™ Accessory Box

⅜ in. T-Valve
User Manual
SMPS 24V4A Power Adapter with a non-grounded American plug Drain Clamp with ¼ in. Quick Connect

Tubing

5 ft. of white ⅜ in. Tubing
5 ft. of blue ¼ in. Tubing
5 ft. of red ¼ in. Tubing

Quick Connect Locking Clips

in. clips x 2
¼ in. clips x 7

HOW TO INSTALL THE ECHO ROM SYSTEM

Install T-Valve and Source Water Valve

Shut off the cold water valve.
Detach the cold water line from the cold water valve.
Wrap threads of the Source Water Valve and
T-Valve with Teflon tape if needed.
Install the T-Valve onto 5. Attach the cold the cold water valve.
Tubing from the Echo ROT™.
Insert the white ⅜” waterline to the T-Valve.

NOTE
Softened source water will extend the life of the RO Membrane.

WARNING

DO NOT connect to the Hot Water line.
This will damage your Echo RO™.

Plugs are installed onto RO inlet connectors, please remove them before installation.

INSTALL DRAIN CLAMP

Remove the 3 plugs from the elbow connections on the back of the Echo RO™
Choose where the drain clamp will be installed and drill a ¼inch. hole. The foam padding to the inside of the Drain clamp, around the hole.
Find your foam pad. Remove the circular cut-out. Apply the sticky part of the foam padding to the inside of the drain clamp, around the hole.
WARNING: DO NOT drill through both sides of the rain pipe.
Apply the drain clamp to the drain pipe using the included nuts and bolts.
Push the red Tubing into the ¼ in. hole and secure it with a Locking Clip.
Push the red Tubing into the elbow on the back of the Echo RO™ and secure the Tubing with a Locking Clip.

HOW TO INSTALL THE ECHO ROM SYSTEM
Please see the Echo RO Faucet™ installation guide included in the Echo RO Faucet™ box.

Final Steps

Reopen the cold water valve.
Turn the T-Valve switch so that it lines up with the Tubing.

CAUTION: Cut the Tubing cleanly to avoid a poor connection and leaks. The lowest point of the line should be the point of connection to the Drain Clamp. To avoid excess noise as the drain water is flowing to the drain, make sure there is no sag in the line.

FIRST-USE INSTRUCTIONS

Connect the Echo ROM to the Power Adapter and Surge Protector. When the Echo RO™ is powered on, the Echo ROT™ beeps 3 times, flushes for 90 seconds, and the Flush icon flashes.
Flush the Filter for 3 to 5 minutes by turning on the Echo RO faucet™™ and letting the water run.
Turn the Echo RO™ on.
All icons turn on and the Echo RO™ goes into standby mode when the Echo RO™ is pressurized. The Echo RO™ is now ready to be used.

WARNING
IF A SURGE PROTECTOR IS NOT USED YOUR WARRANTY WILL BE VOIDED.
When in use, the Echo RO™ begins dispensing water and the display shows a real-time count of Total Dissolved Solids (TDS) in parts per million (PPM) before and after filtration. The display also shows the Filter Life Indicator and the Power indicator light.

NOTE: It is normal to hear vibration sounds when the Echo RO™ is producing water.

FILTER CARTRIDGE REPLACEMENT

Filter Reminders

There are 6 lighted rectangles on the display representing the lifespan of each
Filter. The lights will extinguish one at a time as the Filter is used. When no rectangles are lit, the Filter’s lifespan is over.

Recommended Replacement Period for Filter Cartridges

NOTE

Filter lifespan is influenced by water quality and daily water consumption, so Filter replacement intervals may vary.
Replace as appropriate based on the Filter Life Indicator.

HOW TO REPLACE CARTRIDGES

Turn off the water and drain the water from the Echo RO™ to depressurize it.
Option 1
Turn off the source water and manually flush the pressure by turning on the
Echo RO Faucet™
If you do this with- out turning off the power, the system will chime 10 times to indicate low pressure until you turn the water back on.
Option 2
Manually flush the Echo RO™ by pressing the
Power the button to wake the display.
Then hold the
Flush the button for about 3 seconds.
The Echo RO™ will flush for a few seconds.
Unplug the Echo RO™.
Open the lid.
Hold the Cartridge handle and rotate 90° counterclockwise then pull it out.
Replace it with the new Cartridge
Cover the Cartridges with the lid.
Align the arrow label and rotate 90° clockwise.

FILTER RESET AFTER REPLACEMENT

Press Select for 3 seconds to enter selection mode.
Keep tapping Select until the correct Filter is selected.
Press the Reset button. The Filter Life
Indicator rectangles will be lit again.

NOTE
The selection mode will exit automatically if there is no operation for 5 seconds.

TROUBLESHOOTING

PRODUCT SPECIFICATIONS

Source-water quality: Portable Water
Voltage and frequency: 100-240V, 50/60Hz
Power input: 96W
Purified water flow: 1.2 L/min.
Source water connection: Cold Waterline
Electric shock resistance: Type I
Source-water TDS: The higher the TDS, the sooner the Filter will need to be replaced.
Source-water chlorine level : The higher the chlorine level, the sooner the Carbon Block Filter will need to be replaced.
Rejection rate: 90% to 99%
Source-water pressure: 0.1 to 0.04 MPa

SAFETY PRECAUTIONS

Replace Cartridges according to the Filter Life Indicator.
Only use the Power Adapter that came with the Echo RO™.
Always use Surge Protector or Warranty is Voided.
Unplug the Power Adapter and turn off the Source Water Valve for long-term storage.
Do Not store or use in an environment of 0°C/32°F or below.
Handle with care when moving or uninstalling.
When the Echo RO™ is not going to be in use for an extended period (overnight, when the user is on vacation, etc.), turn off the Source
Water T-Valve to avoid a pressure surge that may cause leaks or damage to housings and Filters.
Echo Technologies™ is not responsible for damage caused by this phenomenon.
If issues occur, turn off the power and source water. Check
Troubleshooting Guide and contact Customer Experience for further assistance.

WARNING: Incorrect installation and/or operation could void your warranty. Please protect your investment! READ THIS MANUAL CAREFULLY.

How to Install the Echo RO and Server

Attachments
@ Echo ROMManual.pdf.pdf

Recently viewed articles

Articles in this section

Add comment
The article is closed for comments.

https://support.echowater.com/hc/en-us/articles/17683665417876-Echo-RO- Manual

FAQ

Q: What should I do if issues occur with the Echo RO system?
- A: Turn off the power and source water, consult the troubleshooting guide, and contact Customer Experience for assistance.