The Retro Web DE-100TP D-LINK Network Interface Card Owner’s Manual
- August 6, 2024
- The Retro Web
Table of Contents
The Retro Web DE-100TP D-LINK Network Interface Card
Specifications
- NIC Type: D-LINK DE-100TP
- Transfer Rate: Ethernet 10Mbps
- Data Bus: 8-bit ISA
- Topology: Linear Bus
- Wiring Type: Shielded/Unshielded twisted pair AUI transceiver via DB-15 port
- Boot ROM: Available
Product Usage Instructions:
Jumper Settings
Make sure to set the jumpers according to the specified configurations for
proper functionality.
Boot ROM Setting
Configure the Boot ROM settings by closing or opening the specified pins as
indicated in the manual.
Diagnostic LEDs
- LED1: Status On – Power is on
- LED1: Blinking On – Data is being transmitted
- LED2: Blinking On – Data is being received
- LED3: On – Network connection is good
- LED4: Off – No collisions detected on the network
I/O Base Address Configuration:
Set the I/O base address by positioning the pins as specified in the manual
for the desired address.
FAQ :
-
What should I do if the diagnostic LED indicates a collision on the network?
If a collision is detected, check for any network issues or interference. Ensure proper cable connections and network stability. -
How can I verify if data is being transmitted successfully?
Monitor the LED indicators; if LED1 is blinking, it indicates data transmission. Additionally, check for any error messages on your connected devices.
THE NETWORK INTERFACE CARD TECHNICAL GUIDE
D-LINK
DE-100TP for PC/XT/AT
- NIC Type Ethernet
- Transfer Rate 10Mbps
- Data Bus 8-bit ISA
- Topology Linear Bus
- Wiring Type Shielded/Unshielded twisted paiAUI transceiver via DB-15 port
- Boot ROM Available
| BOOT ROM ADDRESS|
---|---|---
Address JP5A
JP5B JP5C
C0000h| Pins 1 & 2 Closed| Pins 1 & 2 Closed| Pins 1 & 2 Closed
C4000h| Pins 2 & 3 Closed| Pins 1 & 2 Closed| Pins 1 & 2 Closed
C8000h| Pins 1 & 2 Closed| Pins 2 & 3 Closed| Pins 1 & 2 Closed
CC000h| Pins 2 & 3 Closed| Pins 2 & 3 Closed| Pins 1 & 2 Closed
íD0000h| Pins 1 & 2 Closed| Pins 1 & 2 Closed| Pins 2 & 3 Closed
D4000h| Pins 2 & 3 Closed| Pins 1 & 2 Closed| Pins 2 & 3 Closed
D8000h| Pins 1 & 2 Closed| Pins 2 & 3 Closed| Pins 2 & 3 Closed
DC000h| Pins 2 & 3 Closed| Pins 2 & 3 Closed| Pins 2 & 3 Closed
| CABLE TYPE|
---|---|---
Type
JP1A – JP1F
íShielded/Unshielded twisted pair| Pins 1 & 2 Closed
AUI Transceiver via DB-15 port| Pins 2 & 3 Closed
| INTERRUPT REQUEST|
---|---|---
IRQ| JP3A| JP3B| JP3C| JP3D| JP3E| JP3F
2| Closed| Open| Open| Open| Open| Open
í3| Open| Closed| Open| Open| Open| Open
4| Open| Open| Closed| Open| Open| Open
5| Open| Open| Open| Closed| Open| Open
6| Open| Open| Open| Open| Closed| Open
7| Open| Open| Open| Open| Open| Closed
| BOOT| ROM| SETTING|
---|---|---|---|---
Setting| | JP2
íDisabled| Pins 1 & 2 Closed
Enabled| Pins 2 & 3 Closed
| DMA|
---|---|---
DMA| JP4A & JP4E| JP4B & JP4F| JP4C & JP4G| JP4D & JPH
íDisabled| Open| Open| Open| Closed
1| Closed| Open| Closed| Open
2| Open| Closed| Open| Closed
3| Open| Open| Closed| Open
| BOOT ROM ADDRESS|
---|---|---
Address JP5A
JP5B JP5C
C0000h| Pins 1 & 2 Closed| Pins 1 & 2 Closed| Pins 1 & 2 Closed
C4000h| Pins 2 & 3 Closed| Pins 1 & 2 Closed| Pins 1 & 2 Closed
C8000h| Pins 1 & 2 Closed| Pins 2 & 3 Closed| Pins 1 & 2 Closed
CC000h| Pins 2 & 3 Closed| Pins 2 & 3 Closed| Pins 1 & 2 Closed
íD0000h| Pins 1 & 2 Closed| Pins 1 & 2 Closed| Pins 2 & 3 Closed
D4000h| Pins 2 & 3 Closed| Pins 1 & 2 Closed| Pins 2 & 3 Closed
D8000h| Pins 1 & 2 Closed| Pins 2 & 3 Closed| Pins 2 & 3 Closed
DC000h| Pins 2 & 3 Closed| Pins 2 & 3 Closed| Pins 2 & 3 Closed
| | BOOT ROM ADDRESS|
---|---|---
Address JP5A
JP5B JP5C
C0000h| Pins 1 & 2 Closed| Pins 1 & 2 Closed| Pins 1 & 2 Closed
C4000h| Pins 2 & 3 Closed| Pins 1 & 2 Closed| Pins 1 & 2 Closed
C8000h| Pins 1 & 2 Closed| Pins 2 & 3 Closed| Pins 1 & 2 Closed
CC000h| Pins 2 & 3 Closed| Pins 2 & 3 Closed| Pins 1 & 2 Closed
íD0000h| Pins 1 & 2 Closed| Pins 1 & 2 Closed| Pins 2 & 3 Closed
D4000h| Pins 2 & 3 Closed| Pins 1 & 2 Closed| Pins 2 & 3 Closed
D8000h| Pins 1 & 2 Closed| Pins 2 & 3 Closed| Pins 2 & 3 Closed
DC000h| Pins 2 & 3 Closed| Pins 2 & 3 Closed| Pins 2 & 3 Closed
| DIAGNOSTIC LED(S)|
---|---|---
LED Status
Condition
LED1| On| Power is on
LED1| Blinking| Data is being transmitted
LED2| On| Network connection is good
LED2| Blinking| Data is being received
LED3| On| Collision detected on the network
LED3| Off| No collisions detected on the network
LED4| Off| Normal operation
LED4| On| Transmission interrupted due to abnormally long data stream output
| I/O BASE ADDRESS|
---|---|---
Address JP6A JP6B
JP6C JP6D JP6E
100h| Pins 1 & 2| Pins 2 & 3| Pins 1 & 2| Pins 1 & 2| Pins 1 & 2
120h| Pins 1 & 2| Pins 2 & 3| Pins 1 & 2| Pins 1 & 2| Pins 2 & 3
140h| Pins 1 & 2| Pins 2 & 3| Pins 1 & 2| Pins 2 & 3| Pins 1 & 2
160h| Pins 1 & 2| Pins 2 & 3| Pins 1 & 2| Pins 2 & 3| Pins 2 & 3
180h| Pins 1 & 2| Pins 2 & 3| Pins 2 & 3| Pins 1 & 2| Pins 1 & 2
1A0h| Pins 1 & 2| Pins 2 & 3| Pins 2 & 3| Pins 1 & 2| Pins 2 & 3
1C0h| Pins 1 & 2| Pins 2 & 3| Pins 2 & 3| Pins 2 & 3| Pins 1 & 2
1E0h| Pins 1 & 2| Pins 2 & 3| Pins 2 & 3| Pins 2 & 3| Pins 2 & 3
200h| Pins 2 & 3| Pins 1 & 2| Pins 1 & 2| Pins 1 & 2| Pins 1 & 2
220h| Pins 2 & 3| Pins 1 & 2| Pins 1 & 2| Pins 1 & 2| Pins 2 & 3
240h| Pins 2 & 3| Pins 1 & 2| Pins 1 & 2| Pins 2 & 3| Pins 1 & 2
260h| Pins 2 & 3| Pins 1 & 2| Pins 1 & 2| Pins 2 & 3| Pins 2 & 3
280h| Pins 2 & 3| Pins 1 & 2| Pins 2 & 3| Pins 1 & 2| Pins 1 & 2
2A0h| Pins 2 & 3| Pins 1 & 2| Pins 2 & 3| Pins 1 & 2| Pins 2 & 3
2C0h| Pins 2 & 3| Pins 1 & 2| Pins 2 & 3| Pins 2 & 3| Pins 1 & 2
2E0h| Pins 2 & 3| Pins 1 & 2| Pins 2 & 3| Pins 2 & 3| Pins 2 & 3
í300h| Pins 2 & 3| Pins 2 & 3| Pins 1 & 2| Pins 1 & 2| Pins 1 & 2
320h| Pins 2 & 3| Pins 2 & 3| Pins 1 & 2| Pins 1 & 2| Pins 2 & 3
340h| Pins 2 & 3| Pins 2 & 3| Pins 1 & 2| Pins 2 & 3| Pins 1 & 2
360h| Pins 2 & 3| Pins 2 & 3| Pins 1 & 2| Pins 2 & 3| Pins 2 & 3
380h| Pins 2 & 3| Pins 2 & 3| Pins 2 & 3| Pins 1 & 2| Pins 1 & 2
3A0h| Pins 2 & 3| Pins 2 & 3| Pins 2 & 3| Pins 1 & 2| Pins 2 & 3
3C0h| Pins 2 & 3| Pins 2 & 3| Pins 2 & 3| Pins 2 & 3| Pins 1 & 2
3E0h| Pins 2 & 3| Pins 2 & 3| Pins 2 & 3| Pins 2 & 3| Pins 2 & 3
Note: Pins designated should be in the closed position.