ROGUE Outcast 1M Beam LED Moving Head User Guide

ROGUE Outcast 1M Beam LED Moving Head

Specifications

• Model ID: ROGUEOUTCAST1MBEAM
• Power Requirements: 100-240V AC, 50/60 Hz
• Current Draw:
  • 100 V, 60 Hz – 2.32 A
  • 120 V, 60 Hz – 1.95 A
  • 208 V, 60 Hz – 1.11 A
  • 230 V, 50 Hz – 0.990 A
  • 240 V, 50 Hz – 0.960 A

Product Usage Instructions

Safety Notes
Before using the Rogue Outcast 1M Beam, carefully read and adhere to the safety notes provided in the user manual. These notes contain important information regarding installation, operation, and maintenance.

Power Linking
To power link multiple Rogue Outcast 1M Beam products, ensure not to exceed 12A on a single circuit. You can refer to the provided table for current draw values at different voltages and frequencies. Power-linking cables are available for separate purchase.

Mounting
Prior to mounting the product, review the Safety Notes section. Use a minimum of 2 mounting points per product and ensure that the mounting clamps can support the weight of the unit. For compatible mounting clamps from our Chauvet line, visit trusst.com.

Control Panel Description
The control panel of the Rogue Outcast 1M Beam has the following button functions:

• Exit Button: Exits from the current menu or function.
• Enable Button: Enables the currently displayed menu or sets the selected value.
• Navigation Buttons: Navigate through menus or adjust numeric values.

Frequently Asked Questions (FAQ)

• How can I access the complete User Manual?
  You can scan the QR code provided in the manual to access the product page, warranty terms, and the complete user manual online.

• Where can I purchase power-linking cables?
  Power-linking cables for the Rogue Outcast 1M Beam can be purchased separately from authorized retailers or online stores.

Safety Notes

These Safety Notes include important information about installation, use, and maintenance of the Rogue Outcast 1M Beam.

• The luminaire is intended for professional use only.
• The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than 16.40 ft (5 m) is not expected.
• If the external flexible cable or cord of this luminaire is damaged, it shall be replaced by a special cord or cord exclusively available from the manufacturer or its service agent.
• The light source contained in this luminaire shall only be replaced by the manufacturer or its service agent or a similar qualified person.
• CAUTION:
  • This product’s housing may be hot when operating. Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
  • When transferring the product from extreme temperature environments, (e.g., cold truck to warm humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow the product to fully acclimate to the surrounding environment before connecting it to power.
  • Flashing light is known to trigger epileptic seizures. User must comply with local laws regarding notification of strobe use.
• ALWAYS:
  • Disconnect from power before cleaning the product or replacing the fuse.
  • Replace the fuse with the same type and rating.
  • Use a safety cable when mounting this product overhead.
  • Connect this product to a grounded and protected circuit.
• DO NOT:
  • Open this product. It contains no user-serviceable parts.
  • Look at the light source when the product is on.
  • Leave any flammable material within 20 cm of this product while operating or connected to power.
  • Connect this product to a dimmer or rheostat.
  • Operate this product if the housing, lenses, or cables appear damaged.
  • Submerge this product (IP65). Regular outdoor operation is fine.
  • Permanently install outdoors in locations with extreme environmental conditions. This includes, but is not limited to:
  • Locations where normal temperatures exceed the temperature ranges in this manual.
  • Locations that are prone to flooding or being buried in snow.
  • Other areas where the product will be subject to extreme radiation or caustic substances.
• ONLY use the hanging/mounting bracket to carry this product.
• The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures.
• The minimum startup temperature is -4°F (-20°C). Do not start the product at lower temperatures.
• The minimum ambient temperature is -14°F (-10°C). Do not operate the product at lower temperatures.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.
• In the event of a serious operating problem, stop using immediately.

What is Included

• Rogue Outcast 1M Beam
• Seetronic Powerkon IP65 power cable
• Omega bracket with mounting hardware
• Quick Reference Guide

AC Power

This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz.

AC Plug

FCC Statement of Compliance

This device complies with Part 15 Part B of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Power Linking

It is possible to power link Rogue Outcast 1M Beam products. See the table below for the current draw at each voltage and frequency:

 | 100 V, 60 Hz| 120 V, 60 Hz| 208 V, 60 Hz| 230 V, 50 Hz| 240 V, 50 Hz
---|---|---|---|---|---
Current Draw| 2.32 A| 1.95 A| 1.11 A| .990 A| .960 A

Mounting

Before mounting this product, read the Safety Notes. Use at least 2 mounting points per product. Make sure the mounting clamps are capable of supporting the weight of the product. For our Chauvet line of mounting clamps, go to http://trusst.com/productcategory/truss-clamps.

Control Panel Description

selected value into the selected function
< UP>| Navigates upwards through the menu list or increases the numeric value when in a function
< DOWN>| Navigates downwards through the menu list or decreases the numeric value when in a function

Contact Us

• Chauvet World Headquarters
  • Address: 3360 Davie Rd., Suite 509 Voice: 844-393-7575
  • Davie, FL 33314
  • Fax: 954-756-8015
  • Voice: 954-577-4455
  • Email: chauvetcs@chauvetlighting.com
  • Fax: 954-929-5560
  • Toll Free: 800-762-1084
  • Website: www.chauvetprofessional.com
• Chauvet U.K.
  • Address: Pod 1 EVO Park  Little Oak Drive, Sherwood Park, Nottinghamshire, NG15 0EB
  • UK
  • Email: UKtech@chauvetlighting.eu
  • Website: www.chauvetprofessional.eu
  • Voice: +44 (0) 1773 511115
  • Fax: +44 (0) 1773 511110
• Chauvet Benelux
  • Address: Stokstraat 18
  • 9770 Kruishoutem
  • Belgium
  • Website: www.chauvetprofessional.eu
  • Voice: +32 9 388 93 97
  • Email: BNLtech@chauvetlighting.eu
• Chauvet France
  • Address: 3, Rue Ampère
  • 91380 Chilly-Mazarin
  • Email: FRtech@chauvetlighting.fr
  • France
  • Website: www.chauvetprofessional.eu
  • Voice: +33 1 78 85 33 59
• Chauvet Germany
  • Address: Bruno-Bürgel-Str. 11
  • 28759 Bremen
  • Email: DEtech@chauvetlighting.de
  • Germany
  • Website: www.chauvetprofessional.eu
  • Voice: +49 421 62 60 20
• Chauvet Mexico
  • Address: Av. de las Partidas 34 – 3B (Entrance by Calle 2)  Zona Industrial Lerma Lerma, Edo. de México, CP 52000
  • Email: servicio@chauvet.com.mx
  • Website: www.chauvetprofessional.mx
  • Voice: +52 728-690-2010

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>