Rogue Audio 1053987 Float Switch Manifold Instructions
- August 14, 2024
- Rogue Audio
Table of Contents
Rogue Audio 1053987 Float Switch
INTRODUCTION
Congratulations on your purchase decision! We at Rogue Audio truly believe
that our amplifiers provide the “smartest” value in high-end audio. If you
have never owned a vacuum tube amplifier you will be thrilled by the silky-
smooth sound and incredible detail that only a tube amplifier can provide. The
DragoN Monoblock amplifiers combines the best of tube and solid state
amplification to give you great tube amp sound without any of the normal tube
amp maintenance.
At Rogue Audio we are extremely proud of our products and want you to enjoy
them to their fullest potential. So please, take the time to read through this
short manual so that you can be confident that you have set up your amplifier
properly.
UNPACKING YOUR AMPLIFIER
Tools required: none
WARNING – This amplifier uses voltages that could cause injury or death.
Never open the amplifier while it is plugged in, and always wait at least one
hour after turning the unit off to unplug and open the unit.
Lethal voltages can remain in the electronics after the unit is unplugged.
Your amplifier has been painstakingly inspected for cosmetic flaws during and after assembly. In order not to damage the cosmetic appearance of the amplifier it is important that you follow the unpacking instructions carefully.
- Carefully lift the amplifier out of the box, and remove the foam pads and plastic bag.
- Save the packing materials. The packing materials and box have been carefully designed to protect your valuable equipment during shipping so you don’t want to throw them away.
HOOKING UP YOUR AMPLIFIER
Connecting the amplifier to the loudspeakers:
The rear panel has five way binding posts with which you can connect your loudspeakers as shown in Figure 1. These binding posts accommodate any of the popular speaker terminations available including spades and bananas.
Connecting the amplifier to the preamplifier:
There are two types of input connections on the rear panel of the amplifiers, selectable with a toggle switch:
- Fully balanced XLR type input (toggle switch up)
- RCA input (toggle switch down)
The input connections can be made using either the XLR or RCA input, depending
on your system setup.
Note that if you have a variable output CD player you can choose to drive the
amplifiers with it directly.
Figure 1. Rear panel layout
Connecting the amplifiers to the power outlet:
Connect the IEC end of the detachable power cord provided to the amplifier and
plug the opposite end into a suitable power outlet. It is recommended that the
amplifiers and your preamplifier are plugged into the same wall outlet if
possible (perhaps using a power outlet strip). This is to avoid creating a
ground loop.
OPERATION OF YOUR AMPLIFIER
After all proper connections have been made you are now ready to turn the
amplifier on. The main power on/off switch is on the rear of the amplifier and
should be left on at all times. A small amount of power is used by the
amplifier to maintain a ready state which keeps the solid state components
warmed up for better performance. The power switch on the front of the amp is
used to turn on and off the tube circuitry as well as to take the solid state
components out of their standby mode. There are three LED’s on the front panel
as shown in figure 2.
The yellow LED indicates that the amplifier is in standby mode. The blue LED
indicates that the amplifier is fully operational. The red LED indicates that
a problem has occurred (shorted speaker terminals or other source of
overcurrent).
When the unit is first plugged in and the rear switch is turned on the yellow
standby LED will be illuminated. When the front power button is first
depressed both the blue and yellow LED’s will be illuminated. After
approximately 30 seconds the yellow LED will turn off indicating that the
amplifier is operational and ready to play music.
Some preamplifiers and sources can generate dangerous transients that can damage loudspeakers. To avoid letting dangerous transients reach your loudspeakers turn your system on in the following order:
- Turn on all sources (CD, tuner, etc.) that you will be using.
- Turn on the preamplifier.
- Wait until the preamplifier has stabilized.
- Power up the amplifier
- Select listening source and play music When powering down your system turn the amplifiers off first.
Note – After turning off the amplifiers, wait at least one minute to turn them back on. Do not turn them on then off and then on again in quick succession. Doing this will not allow the power supplies to discharge between on/off cycling and may result in dangerous transient noises.
TROUBLESHOOTING
Speaker Hum – If hum can be heard from more than a few inches from the loudspeaker, there is probably a ground loop. Be sure that the amp and preamp are both plugged into the same outlet or power strip. If this fails to cure the hum, call customer service at Rogue Audio for further advice.
Red LED on front panel is illuminated – Check speaker wires to see if they are shorted together at the rear of the amp or at the speakers.
No Sound from speaker – Check that your speaker cables and interconnects are properly connected. Make sure input toggle switch is set for the correct input.
No LED’s are illuminated – Check that the power cord is properly installed and that the rear switch is turned on.
If you still have a problem please contact Rogue Audio at 570-992-9901
OWNER AND WARRANTY REGISTRATION FORM
Included with this manual is an Owner and Warranty Registration Form. Please take a minute to fill out this card and return it to Rogue Audio. This card must be returned within 30 days of purchase to validate the warranty.
TUBE AND FUSE VALUES
Tubes – One 12AU7
Main fuse located on rear panel (1) – 6.3 Amp slow blow
Power Supply Fuses on PCB (2) – 6.3 Amp slow blow
SPECIFICATIONS
output power | 325 WPC 8 ohm |
---|
525 WPC 4 ohm
frequency response| 20Hz – 20 kHz + 1dB
THD| < 0.1% typ, < 1% at rated power
input sensitivity| 0.75 V RMS
dimensions| 12.25” W x 19” D x 5.5” H
weight| 33 pounds (15 Kg)
shipping weight| 40 lbs (19 Kg)
power requirements| 115/230V – 50/60Hz
LIMITED WARRANTY
Warranty Period
This product has been manufactured under the highest standards of quality and
workmanship. Rogue Audio Inc. (hereinafter “Rogue Audio”) warrants this
product against defects in material or workmanship as follows:
With the exception of vacuum tubes, Rogue Audio warrants to the original
purchaser of this product all parts of this product against defects in
material and workmanship for a period of three years from the date of retail
purchase. Rogue Audio warrants the vacuum tubes for a period of six months
from the date of retail purchase. Any defective parts will be replaced free of
charge, excluding shipping and handling.
Proof of purchase in the form of a bill of sale or recited invoice which
indicates that the product is within the warranty period must be presented to
obtain warranty service. Rogue Audio suggests that the purchaser retain the
dealer’s bill of sale as evidence of the date of retail purchase.
What’s Not Covered
This warranty does not cover cosmetic damage or any damage that results from
product misuse, product abuse, installation error, connection to an improper
voltage supply, accident, improper maintenance, alterations, modifications not
authorized in writing by Rogue Audio, lightening, power surges, or acts of
God.
Use of any other than Rogue Audio factory parts may void this warranty.
This warranty does not cover the cost of parts and labor which would be
otherwise provided without charge under this warranty, obtained from any
source other than Rogue Audio.
This warranty applies only to consumer use of this product and does not cover
any product that is used in any trade or business, or in an industrial or
commercial application.
This warranty applies only to the original purchaser of this product when
purchased from an Authorized Rogue Audio dealer.
This warranty is valid only in the United States.
YOUR RIGHTS
ROGUE AUDIO LIMITS ITS OBLIGATIONS UNDER ANY IMPLIED WARRANTIES UNDER STATE LAWS TO A PERIOD NOT TO EXCEED THE WARRANTY PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, AND SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
To Obtain Service
To obtain service, you must contact Rogue Audio and obtain a return
authorization number. The product must be delivered to Rogue Audio in its
original packaging prepaid at the following address:
Rogue Audio Inc.
545 Jenna Drive Brodheadsville, PA 18322
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>