breezway L5501RBCP Breezeway Power Louvre Windows User Guide

breezway L5501RBCP Breezeway Power Louvre Windows

Specifications

• Product Name: PowerlouvreTM
• Power Requirements: 10-18 blade high windows
• Control Options: Various control methods including DC motor control, Building Management System integration, DIY Automation Systems
• Power Input: 24v DC

Product Usage Instructions

Power Requirements

The PowerlouvreTM is designed for use in bay windows with 10-18 blade high configurations. A bay refers to a grouping of louvre blades separated by vertical mullions.

Switching/Control

To operate the Powerlouvre window

• Supply +ve current to the +ve wire (white stripe) to close the window.
• Supply -ve current to the +ve wire (white stripe) to open the window.

Control Options

Control Option 1

For a single channel setup with Apptivate Control Unit:

• Connect the 24v DC Power +ve supply to the white stripe wire.
• Motor Group 1 controls the Powerlouvre Window.

Control Option 2

Integrating with a Building Management System:

• Supply current of appropriate polarity for a set amount of time to operate the Powerlouvre Window.
• Example: Provide current for 7 seconds to open halfway, 20 seconds to open fully.

Control Option 3

Utilizing DIY Automation Systems:

• Compatible with systems like Belkin Wemo Maker.
• Bell press switches like Clipsal 30MBPR and HPM 770XM can be used.

Installation

Refer to the manufacturer’s instructions for installation details.

Maintenance

Maintenance and replacement can be easily carried out during the building’s life. Visit www.breezway.com.au for care and maintenance instructions.

Power Requirements

• Low voltage 24V DC
  DO NOT USE HIGH VOLTAGE – MAX 29V LIMIT.

• 4 Amps per motor instantaneous startup current.

• 25 Amps per motor constant current.

• 1 motor per bay in 2-9 blade high windows; 2 motors per bay in 10-18 blade high windows.

(‘Bay’ = grouping of louvre blades, separated by vertical mullions)

• Breezway switch mode transformers available, models suitable for powering up to 6 Powerlouvre motors or 14 Powerlouvre motors.
• Transformers for motor groups larger than 14 Powerlouvre motors can be sourced from electrical
• Voltage drop off:
  • Voltage below 24v at motors will cause motors to operate slowly.
  • Voltage significantly below 24v at motors will not close the windows completely.

Switching/Control

• Switches are not included with Powerlouvre
• Polarity of DC current determines movement direction of Powerlouvre motor:
  • +ve current supplied to +ve wire (white stripe) into Powerlouvre = Powerlouvre window closes.
  • -ve current supplied to +ve wire (white stripe) into Powerlouvre = Powerlouvre window opens.
• Limit switches on motors prevent current from reaching motors when windows are fully open/closed (continuing to supply current will therefore not harm the system).
• Powerlouvre Windows in Breezway Frames 2-9 blades high have a single pair of wires emerging from the top right corner of the window frame (as viewed from inside the building). This pair of wires is connected to all of the motors controlling all of the blades within the Powerlouvre
• Powerlouvre Windows in Breezway Frames 10-18 blades high have two pairs of wires emerging from the top right hand corner of the window frame (as viewed from inside the building). One pair of wires is connected to all of the motors controlling all of the upper blades within the Powerlouvre Window and is labelled “1”, the other pair of wires is connected to all of the motors controlling all of the lower blades within the Powerlouvre Window and is labelled “2”. (Check with the window fabricator for wiring details of Powerlouvre Components within window fabricator’s frames)
• Multiple Powerlouvre Windows can be controlled by a single switch by wiring the windows together in parallel.

Features & benefits

• Touch sensitive wall
• Smartphone
• Automatic operation in response to timers and built-in temperature
• Polarity sensing power inputs for easy installation.
• Two models:
• Single
• Dual
• Max 6 Powerlouvre motors per
• Noise passed through some switch mode transformers (eg Meanwell GS40 series) can cause Apptivate Control Units to It is recommended that third party

BUILDING MANAGEMENT SYSTEM

Figure 1 shows how the L5501RBCP is used with a DC motor. When Open is activated, positive polarity is applied to the motor; when Close is activated, negative polarity is applied. In this configuration two power supplies are required.

• Features & benefits:
  • Integration of multiple home systems (eg lighting, blinds, windows, AV)
  • Integration of external sensors (eg light, rain, wind)
• Reviewed by all major suppliers for
• May require
• May require separate transformers to open and to
• Powerlouvre Window cannot report it’s open/closed status back to the BMS.
  • Current of appropriate polarity can be supplied for set amount of time to operate Powerlouvre
  • Example:
  • If movement from fully closed to fully open takes 14 seconds…
  • Provide current for 7 seconds to open half
  • Provide current for 20 seconds to open fully (limit switches will prevent damage to motors from supplying current for longer than required).
  • Provide current for 20 seconds to close
  • C-Bus advice
  • Clipsal advises that L5501RBCP Shutter Relay is simplest Powerlouvre Window to C-Bus (Changeover Relay L5504RVFC is also an alternative, but not Clipsal’s recommended option).
  • Two power supplies are
  • Maximum load of 2A on the Shutter
  • Further details http://www2.clipsal.com/
  • Enclosure for Shutter Relay is available – see Clipsal Catalogue (5501RE)

The terminals of the L5501RBCP are labelled for use with an AC motor. When using a DC motor, attach the provided DC termination label over the factory terminal label. Refer to Figure 2.

DIY AUTOMATION SYSTEMS

(eg Belkin Wemo Maker)

• Features & benefits vary per system, but can include:
  • Control remotely via Wi-Fi
  • Automation in response to Smartphone Applications
• May require

BELL PRESS SWITCHES

• Features & benefits:
  • Simple pair of push-and-hold switches
• Two switches (‘Open’ & ‘Close’)
• Recommended normally-open, bell-press switches: o Clipsal 30MBPR.
  • HPM

Installation

• Wiring emerges from the top right (viewed from inside) corner of the Breezway Window (Check with the window fabricator for wiring details of Powerlouvre Components within the window fabricator’s frames)

• DO NOT PULL ON WIRES EMERGING FROM THE WINDOW FRAME

• Powerlouvre windows can be operated on-site using 18v power-tool batteries without switches – connect wires from Powerlouvre Window directly to battery

  • change polarity to change the direction of operation.

• 24V DC transformers should be installed so that: o They are easily accessible.

  • Power cycling of transformers is possible.

Maintenance and replacement can be readily carried out during the life of the building.

(see www.breezway.com.au for care and maintenance instructions.)

FAQ

Q: Can I use the PowerlouvreTM in windows with fewer than 10 blades?

A: The PowerlouvreTM is specifically designed for use in windows with 10-18 blades high. Using it in windows with fewer blades may not provide optimal performance.

Q: How do I integrate the PowerlouvreTM with a Building Management System?

A: Supply current of appropriate polarity for a specific duration as outlined in the manual to operate the Powerlouvre Window through the Building Management System.

References

• Breezway Altair Aluminium Louvre Windows - Australia

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>