Shelly Europe WAVE2PMSHUT Wave Shutter User Guide
- July 26, 2024
- Shelly Europe
Table of Contents
Wave Shutter
LEGEND
Device terminals:
- N: Neutral terminal
- L: Live terminals (120 V AC)
- SW1: Input terminal for switch/push-button UP (open)
- SW2: Input terminal for switch/push-button DOWN (close)
- O1: Output terminal for motor UP (open)
- O2: Output terminal for motor DOWN (close)
Wires:
- N: Neutral wire
- L: Live wire (120 V AC)
Button:
- S: S button (Fig. 6)
Packaging contents: Device, user guide, Z-Wave™ DSK label
USER AND SAFETY GUIDE
Z-Wave™ shutter control with power measurement
READ BEFORE USE
This document contains important technical and safety information about the
Device, its safe use and installation.
⚠CAUTION! Before beginning the installation, please read carefully and entirely this guide and any other documents accompanying the device. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of law or refusalof legal and/or commercial guarantee (if any). Shelly Europe Ltd. is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.
TERMINOLOGY
Gateway – A Z-Wave™ gateway, also referred to as a Z-Wave™ controller, Z-Wave™ main controller, Z-Wave™ primary controller, or Z-Wave™ hub, etc., is a device that serves as a central hub for a Z-Wave™ smart home network. The term “gateway” is used in this document. S button – The Z-Wave™ Service button, which is located on Z-Wave™ devices and is used for various functions such as inclusion (adding), exclusion (removing), and resetting the device to its factory default settings. The term “S button” is used in this document. Device – In this document, the term “Device” is used to refer to the Shelly Qubino device that is a subject of this guide.
ABOUT SHELLY QUBINO
Shelly Qubino is a line of innovative microprocessor-managed devices, which allow remote control of electric circuits with a smartphone, tablet, PC, or home automation system. They work on Z-Wave™ wireless communication protocol, using a gateway, which is required for the configuration of devices. When the gateway is connected to the internet, you can control Shelly Qubino devices remotely from anywhere. Shelly Qubino devices can be operated in any Z-Wave™ network with other Z-Wave™ certified devices from other manufacturers. All mains operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. Devices are designed to work with older generations of Z-Wave™ devices and gateways.
ABOUT THE DEVICE
The Device enables remote control of motorized blinds, roller shutters, venetian blinds, awnings, etc. It measures power consumption of the connected device. It is recommended to use only motors with electronic or mechanical limit switches. The motor limit switches must be set correctly before connecting the Device to the motor.
INSTALLATION INSTRUCTIONS
The Device can control a bi-directional AC motor.
It can be retrofitted into standard electrical wall boxes, behind the switches
or other places with limited space. For the installation instructions, refer
to the wiring schemes (Fig. 1-5) in this user guide. If you want to use the
Device with a push-button, refer to the Fig. 1 and Fig. 2. For a switch, refer
to the Fig. 3 and Fig. 4.
⚠CAUTION! Danger of electrocution. Mounting/installa- tion of the Device
to the power grid has to be performed with caution, by a qualified
electrician.
⚠WARNING! Danger of electrocution. Every change in the connections has to
be done after ensuring there is no voltage present at the Device terminals.
⚠CAUTION! Use the Device only with a power grid and appliances that
comply with all applicable regulations. A short circuit in the power grid or
any appliance connected to the Device may damage it.
⚠CAUTION! Do not connect the Device to appliances exceeding the given
max. load!
⚠CAUTION! Do not shorten the antenna.
⚠RECOMMENDATION: Place the antenna as far away as possible from metal
elements as they can cause signal interference.
⚠CAUTION! Connect the Device only in the way shown in these instructions.
Any other method could cause damage and/or injury.
⚠CAUTION! Do not install the Device where it can get wet.
⚠CAUTION! Do not use the Device if it has been damaged!
⚠CAUTION! Do not attempt to service or repair the Device yourself!
⚠RECOMMENDATION: Connect the Device using solid single-core cables or
stranded cables with ferrules. The cables should have insulation with
increased heat resistance, not less than PVC T105°C (221°F).
⚠CAUTION! Before starting the mounting/installation of the Device, check
that the breakers are turned off and there is no voltage on their terminals.
This can be done with a phase tester or multimeter. When you are sure that
there is no voltage, you can proceed to connecting the wires.
⚠CAUTION! Use only one phase AC circuit. Do not use mixed AC and DC
circuits.
⚠RECOMMENDATION: For inductive appliances that cause voltage spikes
during switching on/off, such as electrical motors, fans, vacuum cleaners and
similar ones, RC snubber (0.1 µF / 100 Ω / 1/2 W / 600 V AC) should be
connected parallel to the appliance.
⚠CAUTION! Do not allow children to play with the push-buttons/ switches connected to the Device. Keep the devices for remote control of Shelly Qubino (mobile phones, tablets, PCs) away from children.
SPECIFICATIONS
| Power supply | 120 V AC, 50/60Hz |
|---|---|
| Power consumption | < 0.3 W |
| Power measurement (W) | Yes |
| Max. switching voltage AC | 120 V |
| Max. switching current AC | 8 A per channel |
| Max. power per channel | 1/3 hp |
| Overheating protection | Yes |
| Overload protection | Yes |
| Distance | Up to 40 m indoors (131 ft.) (depends on local condition) |
| Z-Wave”” repeater | Yes |
| CPU | Z-Wavem S800 |
| Z-Wave”” frequency bands | 908,4 MHz |
| Maximum radio frequency power transmitted in frequency band(s) | < 25 mW |
| Size (H x W x D) | 37x42x16 ±0.5 mm / 1.46×1.65×0.63 ±0.02 in |
| Weight | 29 g / 1.02 oz. |
| Mounting | Wall console |
| Screw terminals max. torque | 0.4 Nm / 3.5 bin |
| Conductor cross section | 0.5 to 1.5 mm2 / 20 to 16 AWG |
| Conductor stripped length | 5 to 6 mm / 0.20 to 0.24 in |
| Shell material | Plastic |
| Color | Black |
| Ambient temperature | -20°C to 40°C / -5°F to 105°F |
| Humidity | 30% to 70% RH |
| Max. altitude | 2000 m / 6562 ft. |
OPERATIONAL INSTRUCTIONS
If the inputs are configured as push-buttons:
- Pressing the push-button when the blind is static, moves the blind in the corresponding direction until the endpoint is reached.
- Pressing the push-button for the same direction while the blind is moving, stops the blind.
- Pressing the push-button for the opposite direction while the blind is moving, reverses the blind movement until the endpoint is reached.
If the inputs are configured as switches:
- Turning the switch on moves the blind in the corresponding direction until the endpoint is reached.
- Turning the switch off stops the blind movement.
- If both switches are turned on, the Device respects the last engaged switch. Turning off the last engaged switch stops theblind movement, even if the other switch is still on.
- To move the blind in the opposite direction, the other switch has to be turned off and on again.
SUPPORTED LOAD TYPES
Inductive with RC Snubber (120 V AC electric motors)
IMPORTANT DISCLAMER
Z-Wave™ wireless communication may not always be 100% reliable. This Device
should not be used in situations in which life and/or valuables are solely
dependent on its functioning. If the Device is not recognized by your gateway
or appears incorrectly, you may need to change the Device type manually and
ensure that your gateway supports Z-Wave Plus™ multi-channel devices.
DISPOSAL & RECYCLING
This refers to the waste of electrical and electronic equipment. It is
applicable in the US and other countries to collect waste separately.
This symbol on the product or in the accompanying literature indicates that
the product should not be disposed of in the daily waste. Wave Shutter must be
recycled to avoid possible damage to the environment or human health from
uncontrolled waste disposal and to promote the reuse of materials and
resources. It is your responsibility to dispose of the device separately from
general household waste when it is already unusable.
FCC NOTES
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The manufacturer is
not responsible for any radio or TV interference caused by unauthorized
modification or change to this equipment. Such modifications or change could
void the user’s authority to operate the equipment. This equipment has been
tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. The device has been evaluated to meet general RF
exposure requirement. The device can be used in portable exposure condition
without restriction.
ORDERING CODE: QNSH-001P10US
MANUFACTURER
Shelly Europe Ltd. (former Allterco Robotics EOOD)
Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria
Tel.: +359 2 988 7435
E-mail: zwave-shelly@shelly.cloud
Support: https://support.shelly.cloud/
Web: https://www.shelly.com
Changes in the contact data are published by the Manufacturer at the official
website: https://www.shelly.com
EXTENDED USER GUIDE
For more detailed installation instructions, use cases, and comprehensive
guidance on adding/removing the Device to/from a Z-Wave™ network, factory
reset, LED signalization, Z-Wave™ command classes, parameters, and much more,
refer to the extended user guide at: https://shelly.link/WaveShutter-KB-US
https://shelly.link/WaveShutter-KB-US
B4123
V 0.0.2
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>