Auto tracking tripod

C12 Series

Product Introduction

Direction for Use

Pull out the phone clip to install the phone

Unlock the head when using the head

Lift unlock 360 to use rocker arm.

Open stand from bottom

Tighten the knob to secure the phone clip

push up the remote to remove it

Intelligent Tacking Head

Tip: Please unlock the tracking head before turning it on

1. Long press the power button to turn on the power.
2. Click the power button to pause tracking, and the indicator light flashes.
3. Double—click the power button to enter the slow rotation mode, click the power button to stop rotation. Hold for gesture OK 3s to continue tracking.
4. Long press the power button to turn off the device.
5. Charging Use USB 5V adapter to connect to the charging port for charging. When charging, the red indicator light is on. When fully charged, the red indicator light turns green.

Intelligent Gesture Control

Under power—on state
[Gesture—Palm] Hold for 2s until the indicator light is on to stop tracking
[Gesture—OK] Hold for 2 seconds until the indicator light is on to turn on the tracking.

Remote Control

1. Pull the power switch,the indicator light flashes
2. Open the mobile phone Bluetooth and search for the device name: LAIGI
3. Click the pairing is successful, the indicator light will no longer fash
4. Open the pbone camera and press Et  to take photo
5. Open the mobile phone video and press  start, and then press  db to start.
6. Pull the power switch to shut down when not in use

iphone need to do the following settings :

1. Lock screen rotation function

2. Settings -Accessibility – Touch – Assistive Touch (on) AssistiveTouch

3. Settings -Accessibility – Touch – Assist – Tracking Sensitivity (The Tracking Sensitivity function can be found in the drop-down of the Assistive Touch menu content

Move the white point towards the turtle (best between 1/4 and 1/3 of the progress bar)

4. Open the video software TikTok to take pictures/videos.
5. If pressing cannot take a photo/video , the small white floating point on the screen isn’t aligned with the shutter.
   Press and hold , Click to adjust up, down, left and right to make the floating point overlap with the shutter, then you can take photos/videos.

Fill Light

*Fill light is optional

1. Power button: click to turn on the light, click again to switch the light mode until power Off; long press the power button to adjust the brightness of the lignt.
2. Charging: Use the USB 5v adapter to connect to the charging port for charging.

Note

1. Do not store the product in a low—temperature, humid environment.
2. Do not expose the product to high temperatures such as sunlight or fire.
3. Do not use the product in places where the equipment is restricted to avoid violating public order.
4. This product contains small parts, please keep it out of the reach of infants and young children to prevent them from swallowing it accidentally.
5. The pictures and dimensions shown on the package and manual are for reference only, please refer to th e actual product.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• ‐‐ Reorient or relocate the receiving antenna.
• ‐‐ Increase the separation between the equipment and receiver.
• ‐‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• ‐‐ Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>