aigousi MINI Wireless Smart Earphones User Manual
- July 23, 2024
- aigousi
Table of Contents
Aigousi MINI Wireless Smart Earphones
Please read the user manual carefully and store it properly for reference when using this product
configuration parameter
Pairing name : MINI
Chip version :5.4
Charging interface : type • c
Charging time: approximately 1·2H
Product Introduction
- Charging case • 1
- Left and right earphones• 1
- Small earbuds • 1 pair
- Data cable”1
- Product manual “1
Binaural pairing connection
Step 1: Delete the information connected to the phone, and then turn off the wireless connection on the phone.
Step 2 : Return the machine to the charging compartment and wait for 30 seconds.
Step 3 ; Take out the headphones and wear them on your ears.
Step 4: TWS automatically enters pairing mode, automatically matches. the main ear flashes alternately, and the auxiliary ear light goes out.
Step 5 : Open the wireless connection on your phone.
PS: A her the binaural pairing is completed, only one earphone flashes again to indicate successful binaural pairing. If both earphones flash It means that the ears have not been paired successfully.
Switching between Chinese and English
When the earphones are not connected to the phone, three clicks on one of the earphone function keys allow for free switching between Chinese and English.
Operating mode
Power on
- Open the charging case, take out the earphones and immediately tum them on automatically, with a voice prompt of ‘ power on· and the light on for 1 second.
- When the earphones are turned off, press and hold the function button tor 3 seconds. and the voice prompt will “tum on’ and the light will be on for 1 second.
Shutdown
- Open the charging case, take out the earphones and immediately tum them on automatically, with a voice prompt of ‘tum off” and the light on for 1 second.
- When the earphones are turned off, pres5 and hold the function button tor 6 seconds, and the voice prompt will ‘tum off” and the light will be on tor 1 second.
Clear pairing
When the earphones are turned on but not connected to any device, simply tap one of the earphone function keys four times to pair them clearly.
Operating instructions
Volume+
In music mode Right Ear (R) Long press the function key for 0.8 seconds
Volume-
In music mode Left Ear (L) Long press the function key for 0.8 seconds
Voice Assistant
In connected state Any earphone (L/R) Four click function keys
Reject phone calls
Under incoming call status Any earphone (L/R) Long press the function ey for 1
second
Play the next song
In music mode Left Ear (L) Three click function key
Play the previous song
In music mode Right Ear (R) Three click function key
Play/pause music
In music mode Any earphone (L/R) Double click function keys
Answer/hang up calls
During incoming call status Any earphone (L/R) Double click function keys
Cortificate Of conformity
Inspector: 08
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/1V technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement.
This equipment complies with FCC’s RF radiation exposure limits set forth for
an uncontrolled environment. This device and Its antenna(s) must not be co-
located or conjunction with any other antenna or transmitter.