Sunye Light D515 LED Remote Control Dimmer Instruction Manual
- June 6, 2024
- Sunye Light
Table of Contents
Sunye Light D515 LED Remote Control Dimmer
Instruction
WARNING: This product may represent a possible shock or fire hazard if
improperly installed or attached in any way. The product should be installed
in accordance with these instructions.
CAUTION – To reduce the risk of fire, electric shock, or injury to
persons:
- Safety Warnings and Instructions included in this User Guide cannot cover all possible conditions and situations that could occur. Caution and care must be exercised when using or maintaining any personal electronic product.
- LED Remote Control Dimmer Is intended for installation by trained, qualified electrical contractors.
- When using LED Remote Control Dimmer outdoors, only connect to a Ground Fault Circuit Interrupter (GFCI) outlet.
- Not intended for Installation In ceilings, soffits, cabinets, or other enclosed spaces.
- Not Intended for lighting aquariums.3
- Periodically inspect the product for degradation due to weather, UV light, or other damage.
- DO NOT EXCEED THE MAXIMUM 200 WATTAGE CAPACITY!
WARNING RISK OF ELECTRICK SOCK!!
- Disconnect power at source prior to wiring, re-lamping or servicing in any way.
- Do not repair the product if you are not a professional electrician.
LEO REMOTE CONTROL DIMMER HAS A POlARUZEO PLUG.
- The plug supplied with this product is a polarized plug and will only fit into a polarized outlet
- DO NOT EXCEED THEM凶MUM WATTAGE FOR THE PRODUCT.
- Only dimmable LED bulbs are compatible with this product. DO NOT use incandescent bulbs.
- This product has a maximum wattage of 200 watts. (E.g., If using a light string with 15 bulbs rated at 2 watts each, totaling 30 watts-a maximum of 6 sting lights c:an be connected to the LED Remote Control Dimmer.)
INSTALLATION
- Turn off string lights before installation.
- Follow above diagram for installation.
- Dimmer unit can be secured using the “Mounting Holes” as pictured in the diagram.
- Keep the plug In a dry location, the plug is not waterproof. The dimmer body is IP68 Waterproof.
REMOTE CONTROL
(See illustration)
- Pull plastic tab to engage battery.
- The effective operating range is 164 ft. (SO Meters).
- Indicating Light will activate with each press of a button showing the remote is working.
- The red button is On/Off.
- DELAY OFF: Turns unit off in 10 seconds.
- HOTKEYS: 100%, 75%, 50%, and 25% are preset brightness settings
- INCREASE/DECREASE: Press and hold to gradually increase or decrease brightness to a custom setting.
- DIY Buttons: Press and hold any OIY button live seconds to save a custom brightness. The four different OIY buttons allow you to save four different custom settings for future use
- Minimum: Press to lower lighting to the minimum brightness.
- Uses a CR2025 battery.
- Keep the remote control in a dry location always.
- Please don’t OVERLOAD 200W, If run at full load for a long time, the dimmer will get hot and power off automatically. and it will turn on again automatically when the temperature drop.
Thank you for your purchase of the LED Remote Control Dimmer, we hope you’re completely satisfied with your purchase. If you have any questions or are not completely satisfied with your order please contact us at Amazon, and we will be happy to assist you. Our company provides customers with a warranty of 2 years from the date of purchase.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction