MUSWAY MF210Q2 Downfire Subwoofer System Instruction Manual
- July 25, 2024
- musway
Table of Contents
MUSIC IS THE WAY
VERSION 1.1
MF210Q2
DOWNFIRE SUBWOOFER SYSTEM
MF210Q2 Downfire Subwoofer System
CAUTION
Playing very loud music in a vehicle can permanently damage your hearing and
impair your ability to perceive traffic. It is therefore advisable to avoid
using permanently high volumes while driving. We assume no liability for
hearing loss, bodily injury, or property damage resulting from the use or
misuse of this product.
DISPOSAL/RECYCLING
If you have to dispose the subwoofer system, please note that no electronic devices must be disposed in the household waste. Dispose the subwoofer system at a suitable recycling facility in accordance with local waste regulations. If necessary, consult your local authority or dealer. More information at www.audiodesign.de/english/disposal
IMPORTANT NOTES PRIOR TO INSTALLATION
- For the installation, choose a position in the vehicle that does not impair the driver’s field of vision or the safety of the passengers. This is particularly true for airbag zones and seat belts.
- Make sure that the device cannot come loose while driving or injure someone in the passenger compartment. It is recommended to secure the sound system in the trunk using straps or similar fastening methods if possible.
- When installing and fastening the device, make sure that no components of the vehicle (airbags, seat belts, cable harnesses, fuel tank, etc.) are damaged.
- All cables should be kept as short as possible to avoid losses and interference.
- Protect the device from moisture, dust and dirt.
- Please do not screw any other devices such as amplifiers onto the housing. This could damage the electronics.
- The performance and reliability of the sound system depends on the quality of the installation. It is best to have the installation carried out by an installation specialist.
SPECIFICATIONS
MF210Q2| Sealed Downfire
Subwoofer System
---|---
Subwoofer| 20 cm (8”) + 20 cm (8”) passive Subwoofer
Impedance| 2 + 2 Ω
Voice coil| 50 mm (2”)
Magnet driver| 45 Ounces (1.275 g)
Frequency range| 30 – 300 Hz
Power handling
Nominal power handling¹
Music power handling²| 300 Watts/RMS
600 Watts/MAX.
Recommended amplifier power³| 250 – 350 Watts/RMS
Dimensions| 340 x 150 x 700 mm
- The nominal power handling is given in watts RMS and represents an effective value. This corresponds to the average power value of the subwoofer in the corresponding frequency range. The value is determined in a complex measuring process using pink noise. RMS is the abbreviation for “Root Mean Square”.
- The music power handling represents a benchmark that reflects the performance when playing music continuously with loud and quiet passages and pauses. This takes into account that the subwoofer can always “recover” and cool down thermally due to the dynamic music playback.
- The recommended amplifier power depends on the actual output power of the amplifier, which also depends on the connected on-board voltage. In principle, an amplifier should always have around 20-30% more power than the nominal power handling of the speaker specified in RMS in order to avoid distortion or clipping in the audio signal, otherwise the speaker’s voice coil could be damaged.
CONNECTION WITH QUICKCONNECT
Required:
-
Compatible Musway DSP Amplifier such as M6:
-
QuickConnect cable such as: MQC120, MQC300, MQC500
Power handling and impedance per each voice coil (VC): -
125 – 175 Watts/RMS at 2 Ohms
INTERCONNECTION WITH SPRING TERMINALS
Operation with one amplifier
Parallel 1 Ohm
Connect amplifier at VC1 + and VC1 – (250 – 350 Watts/RMS)
Connect VC1+ with VC2 +
Connect VC1 – with VC2 –
Operation with one amplifier
Serial 4 Ohms
Connect amplifier at VC1 + and VC2 – (250 – 350 Watts/RMS)
Connect VC1 – with VC2 +
Operation with two channels
Standard 2 + 2 Ohms
Connect channel 1 at VC1 (125 – 175 Watts/RMS)
Connect channel 2 at VC2 (125 – 175 Watts/RMS)
CAUTION
Ensure the correct polarity of all connections.
MUSIC IS THE WAY
MUSWAY is a brand of Audio Design GmbH
Am Breilingsweg 3 · D-76709 Kronau
Tel. +49 7253 – 9465-0 · Fax +49 7253 – 946510
© Audio Design GmbH, All Rights Reserved
www.musway.de