MUSWAY CSM206C 4 Inch 2-Way Component System Instructions

June 1, 2024
musway

MUSWAY logo CSM206C
CSM206X
SPEAKERS FOR MERCEDES-BENZ
C-CLASS (W206)

IMPORTANT NOTES

  • The installation of the sound system should be carried out by a trained and technically experienced specialist. If you decide to do the installation yourself, please contact your specialist dealer if you have any problems.
  • Please treat all parts and components with care.
  • Under all circumstances, observe the vehicle manufacturer’s instructions and do not make any changes to the vehicle that could impair driving safety.

LEGAL NOTE

  • Musway or Audio Design GmbH are in no way affiliated with Mercedes-Benz Group AG or any of its subsidiaries or affiliates, or acting on their behalf or with their authorization. All registered product names and brand names are the property of their respective owners.
  • Technical changes and errors are subject to change.

DISPOSAL

**** If you need to dispose the speakers and their components, please note that no electronic devices may be disposed with the household waste.
Dispose the speakers and their components at an appropriate recycling facility in accordance with local waste regulations. If necessary, consult your local authority or dealer.
More Information under www.audiodesign.de/english/disposal

SPECIFICATIONS

CSM206C CSM206X

10 cm (4”) 2-Way Component System
60 Watts/RMS, 120 Watts/MAX
Impedance 4 Ohms
Frequency Response 75 – 24000 Hz
10 cm Woofer, Glass Fiber Cone
Dual Neodymium Magnet
25 mm Silk Dome Neodymium Tweeters
Mounting Depth 32 mm
Mounting Diameter 98 mm
Plug+Play Connections| 10 cm (4”) 2-Way Coaxial-Speakers
60 Watts/RMS, 120 Watts/MAX
Impedance 4 Ohms
Frequency Response 75 – 22000 Hz
10 cm Woofer, Glass Fiber Cone
Dual Neodymium Magnet
16 mm Silk Dome Neodymium Tweeters
Mounting Depth 35 mm
Mounting Diameter 98 mm
Plug+Play Connections

CONNECTION DIAGRAM

CSM206C with tweeter already installed ex works:MUSWAY CSM206C 4 Inch 2-Way
Component System - figure 1CSM206C without tweeter preparation ex works:
MUSWAY CSM206C 4 Inch 2-Way Component System - figure
2

INSTALLATION

Start with the passenger door. Loosen the two Torx screws marked above.
Use a plastic wedge to quickly remove the door panel from the bottom upwards
MUSWAY CSM206C 4 Inch 2-Way Component System - figure
3In the outer corner of the door there is a white holder that is not clipped in like the other holders, but is pushed in to the side. This last bracket can only be released by pushing it sideways.MUSWAY CSM206C 4 Inch 2-Way Component System - figure
4Release the lock on the Bowden cable of the door lock.
MUSWAY CSM206C 4 Inch 2-Way Component System - figure
5Now disconnect all connectors from the door.
MUSWAY CSM206C 4 Inch 2-Way Component System - figure
6Use a slotted screwdriver to press the locking catch on the speaker and turn it to the left out of the holder.
MUSWAY CSM206C 4 Inch 2-Way Component System - figure
7Press the speaker connector spring with a slotted screwdriver. Then carefully remove the plug.
MUSWAY CSM206C 4 Inch 2-Way Component System - figure
8Plug the speaker connector* into the Musway speaker and turn it into the holder. Turn to the right until the speaker clicks into place.
MUSWAY CSM206C 4 Inch 2-Way Component System - figure
9If you only install the CSM206X model without a separate tweeter, the installation is complete from here. Reinstall the door panel in the reverse order of the individual installation steps and repeat this on the driver’s door.
Remove the covering of the mirror triangle on the inside corner of the door. This is held at the bottom by a small clamp and across the entire window front by the rubber lip.
MUSWAY CSM206C 4 Inch 2-Way Component System - figure
10Turn the tweeter out of the holder to the left and pull off the connecting cable. Connect this to the Musway tweeter. Then turn this into the holder. Make sure that the corresponding tabs are in the correct position.MUSWAY CSM206C 4 Inch 2-Way Component System - figure
11Reinstall the covering of mirror triangle cover by first sliding it under the rubber seal along the window. At the very end, the small plastic nose must be fixed near the tweeter. Repeat the previous installation steps on the driver’s door.

MUSWAY logoMUSWAY is a brand of Audio Design GmbH
Am Breilingsweg 3 · D-76709 Kronau
Tel. +49 7253 – 9465-0 · Fax +49 7253 – 946510
© Audio Design GmbH, All Rights Reserved
www.musway.de

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals