AnyTone AT505PRO CB Radio Instruction Manual
- July 26, 2024
- AnyTone
Table of Contents
AnyTone AT505PRO CB Radio Instruction Manual
Qixiang Electron Science & Technology Co., Ltd
www.anytone.net
1. ACCESSORIES
2. KNOW ABOUT THIS RADIO
3. LCD
4. HOW TO USE THIS RADIO
4.1 Power On/Off the Radio ………………………………………………………. .
Turn the VOL knob clockwise to power on the radio, the LCD displays the
Norms and then displays channel number.
Turn the VOL knob anti-clockwise, until hear Ka Ta, the radio is powered off
4.2 Volume Control …………………………………………………………………… .
Turn the VOL knob clockwise to increase the volume, turn it anti-clockwise to
decrease the volume.
4.3 ASQ – SQ Control ……………………………………………………………….. .
*ASQ (Automatic Squelch Control)
Turn the SOL knob anti-clockwise into ASO position. 11 AQ II appears on the
LCD. No repetitive manual adjustment and a permanent improvement between the
sensitivity and the listening comfort when ASO is active. This function can be
disconnected by turning the switch clockwise. In this case the squelch
adjustment becomes manual. 11 AQ II disappears from the LCD.
* SQ (Manual Squelch Control)
Turn the SOL knob clockwise to the exact point where all background noises
disappear. This adjustment should be done with precision as, if set to maximum
(fully clockwise), only the strongest signals will be received.
4.4 Channel Selector – SCAN …………………………………………………… .
5. SPECIFICATION
FCC compliance statement
FCC Warning Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference including received interference
that may cause undesired operation.
Note 1: The grantee is not responsible for any changes or modifications
not expressly approved by the party responsible for compliance. Such
modifications could void the user’s authority to operate the equipment.
Replacement of any transmitter component (crystal, semiconductor, etc.) not
authorized by the FCC equipment authorization for this radio could violate FCC
rules.
Note 2: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure and Separation Distance:
This radio transmitter has been approved by FCC to operate with the antenna
types listed below with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna types not included in this
list, having a gain greater than the maximum gain indicated for that type, are
strictly prohibited for use with this device.
External Antenna:
Maximum Antenna Gain: 3 dBi
Antenna lmpedance: 50 Ohms
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 51.2 cm between the radiator& body.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
ISED compliance statement
ISED Warning Statement
ENGLISH: This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
ISED RF Exposure Statement:
ENGLISH: This radio transmitter has been approved by lndustry Canada to
operate with the antenna types listed below with the maximum permissible gain
and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
External Antenna:
Maximum Antenna Gain: 3 dBi
Antenna lmpedance: 50 Ohms
This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 43.1 cm between the radiator & your body.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Hereby, We, declare that the radio is compliance with Radio equipment
Directive (RED)2014/53/EU. The device in the environment with the temperature
between -10 to 55℃ and operating under 2000m, otherwise, it may damage your
radio.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>