safe T sensor NM Countertop Microwave Mounting Kit User Manual

safe T sensor NM Countertop Microwave Mounting Kit

Specifications

• Power Rating: 120VAC, 60Hz, 12Amps
• Product Type: NM

Product Information

This Safe-T-sensorTM device is designed to help prevent microwave oven fires & false alarms. It is not recommended for use on built-in microwaves unless vents are exposed or old style microwaves with a manual dial timer.

Product Usage Instructions

PROBLEM: Microwave does not operate

POSSIBLE CAUSE/SOLUTION

1. The house fuse has blown or the circuit breaker has tripped. Check and/or replace the fuse or reset the circuit breaker.
2. The microwave cord/plug was not plugged properly into the control box. Ensure the cord plug is tightly plugged into the control box.
3. The power box is not plugged properly into the power outlet.
4. Power outage. Check house lights to confirm.

Safe-T-sensor Installation Instructions:

Disconnecting use only. Read all instructions before installation and keep this manual. This product is not for commercial use.

Microwave Cooking Safety Tips:

If there is a fire in your microwave, turn it off immediately and keep the door closed. Do not open the door until the fire is completely out. Have the oven checked and serviced before using it again.

Service & Warranty

Pioneering Technology Corp. warrants the product against defects in materials and workmanship for one (1) year from the date of purchase. The warranty does not cover physical damage from improper installation, misuse, neglect, or accidents.

FAQ

• Q : How long is the warranty for the Safe-T-sensorTM device?
• A : The product is covered by a one-year warranty from the date of purchase, provided it is operated and maintained according to the instructions.

Microwave Cooking Safety Tips from the NFPA

• Never leave cooking unattended.
• Read the manufacturer’sinstructions before using a microwave oven.
• Use only microwave-safe cookware (containers or dishes).
• Open microwaved food slowly, away from the face. Hot steam escaping from a container or the food itself can cause burns.
• Never use aluminum foil or metal objects in a microwave oven.
• If you have a fire in your microwave, turn it off immediately and keep the door closed. Never open the door until the fire is completely out. Have the oven checked and/or serviced before being used again.

Note: The National Fire Protection Association (NFPA) does not test, label, or approve any products.

Introduction

This product is designed to help prevent microwave oven fires& false alarms

Features:

• Automatic shut-off – power to microwave interrupted (shut-off and reset) at the first sign of smoke.
• Auto-reset – power is automatically restored after the cooking process stops.
• Easy to install & use – plug the control box into an outlet; plug the microwave into control box; mount the magnetic sensor microwave just above the louver/vent slots.
• No batteries required

Power Rating/ProductType:

120VAC, 60Hz, 12AmpsProduct Type: NM
This Safe-T-Sensor model is not recommended for use on: built-in microwaves unless vents are exposed old style Microwaves with a manual dial timer

Installation

The Safe-T-sensor™ has two modules:

• Sensor” (smoke sensor) and
• Control box” (power supply box).

1. Plug the “Control box” into a grounded 120VAC receptacle, then plug in the microwave power cord into the “Control box”.
2. Attach the “Magnetized Sensor” to the microwave unit just above or beside the louver/vent slots. The sensor has a built-in magnetic mounting

IMPORTANT

1. Microwave vents have been designed and slanted to expel smoke in a specific direction. It is important that the magnetized sensor be positioned above or beside these vents to ensure the expelled smoke passes directly over/into the sensor.
2. Refer to these sample images to correctly position the sensor on the microwave.
3. In some instances, microwave vents may be located underneath or at the back of the microwave (do not confuse the air intake holes on the back as vents). Again the sensor should be positioned so that expelled smoke will pass directly over/into the sen

Operation & Testing

1. LED on Sensor lights up after connecting power indicating the Sensor is monitoring microwave.
2. To test the operation, press the test button on the Sensor module and hold for 3 seconds. There will be beeping and an LED will flash indicating that the circuit is ready to detect smoke.
3. If smoke is detected by the Sensor it will interrupt power to the microwave, the LED will flash and the Sensor will beep for 5 seconds indicating that the cooking process has stopped then power to the microwave will be restored automatically but cooking will not continue until attended to by the user.
4. Do not immediately open the Microwave when smoke is detected. Visually check for fire, wait 5 minutes then remove contents with heat-protective gloves.

Care
REGULAR TESTING IS REQUIRED. O ENSURE PROPER OPERATION
Once a month check the Sensor module to make sure the slots are free from any debris. The Sensor cover is removable for cleaning. Refer to the images below to correctly clean the Safe-T-sensor™

Steps to clean Safe-T-sensor

1. Unplug the microwave and Safe-T-sensor™ from the power outlet.
2. Gently remove the Sensor cover from the Sensor case.
3. Clean any dust or debris by using a tissue.
4. Place the Sensor cover back on the Sensor case so it clicks back into place.
5. Plug the microwave into Safe-T-sensor™ control box then, plug the control box back into the power outlet.
6. Position the Sensor near the microwave’s louver/vent.

For optimum performance test & clean Safe-T-sensor™ monthly.

Warning! The user cannot service parts inside either module. Do not open the modules. Refer to Section F “Care” for instructions on how to clean Sensor

Troubleshooting

Read this BEFORE you call for service.

You may save the cost and inconvenience of an unnecessary service call by first reviewing this easy-to-use “Troubleshooting Check List” of the most frequently encountered situations, which are not the result of defective workmanship or materials. Your Safe-T-sensor™ device is a carefully engineered product. Many times, what appears to be a reason to call for service is, under certain conditions, a normal operating characteristic of the device

Service & Warranty

Pioneering Technology Corp. warrants that the product is free from defects in materials and workmanship when operated and maintained according to the instructions provided for a period of one (1) year from date of purchase.
This warranty does not cover physical damage caused by improper installation, misuse, neglect or accident. This warranty is VOID if this product has been altered or modified in any way. For service under this warranty contact your Safe-T-sensor™ distributor or Pioneering Technology Corp.

THERE ARE NO OTHER WARRANTIES. PIONEERING TECHNOLOGY CORP. DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHERS THAT VARY FROM STATE TO STATE.
EXCEPT AS STATED HEREIN, IN NO EVENT SHALL PIONEERING TECHNOLOGY CORP. BE LIABLE FOR ANY DAMAGES WHATSOEVER WHETHER BASED ON CONTRACT, TORT, WARRANTY OR OTHER EQUITABLE GROUNDS, INCLUDING, WITHOUT LIMITATION, OR OTHER PECUNIARY LOSS, ARISING OUT OF THE USE OF OR INABILITY TO USE THIS PRODUCT, EVEN IF PIONEERING TECHNOLOGY CORP. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE , THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

Pioneering Technology’s entire liability and your exclusive remedy shall be at Pioneering Technology’s option, either (a) return of the price paid for the product or (b) repair or replacement of the product that does not meet Pioneering Technology’s Limited Warranty and which is returned to Pioneering Technology. In no event shall Pioneering Technology’s liability exceed the purchase price of the product

CONTACT

• Pioneering Technology Corp. Service Dept.
• 2400 Skymark Ave Unit 7 Mississauga, Ontario Canada L4W 5K5
• Tel: 1 800-433-6026 ext 228 or 905-712-2061 ext 228
• Email: service@pioneeringtech.com
• www.pioneeringtech.com

Product is not to be exposed to high humidity (80%) and ambient conditions exceeding 30 degrees C (90 degrees F) or occasionally exposed to water

References

• Pioneering Technology - Smart Cooking Fire Safety Solutions
• Pioneering Technology - Smart Cooking Fire Safety Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>