Music Tribe 911 Envelope Generator User Guide

: July 15, 2024
: Music Tribe

Table of Contents

Music Tribe 911 Envelope Generator
Product Usage Instructions
FAQ
Safety Instruction
LIMITED WARRANTY
Controls ****
Power Connection
Installation
Specifications
FCC STATEMENT
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Music Tribe 911 Envelope Generator

Product Usage Instructions

Safety Instructions

Read and follow all instructions provided in the manual.
Avoid exposing the apparatus to water, except for outdoor products.
Clean the product only with a dry cloth.
Ensure ventilation openings are not blocked and install the product according to the manufacturer’s instructions.
Avoid placing the product near heat sources such as radiators or stoves.
Use only attachments and accessories specified by the manufacturer.
Use specified carts, stands, or tables to prevent tip-overs.
Avoid installing the product in confined spaces like bookcases.
Keep the product away from naked flame sources like lighted candles.

Power Connection

The 911 Envelope Generator module requires connection to a standard Eurorack power supply system. Follow these steps:

Turn off the power supply or rack case power and disconnect the power cable.
Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. Ensure proper alignment with theta and gap in the socket. If there is no keyed socket, align pin 1 (-12V) with the red stripe on the cable.

FAQ

Q: Where can I find more information about the warranty?
A: For detailed warranty terms and conditions, as well as additional information regarding Music Tribe’s Limited Warranty, please visit community.musictribe.com/support.

Safety Instruction

Please read and follow all instructions.
Keep the apparatus away from water, except for outdoor products..
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Use only attachments/accessories specified by the manufacturer.
Use only specified carts, stands, tripods, brackets, or tables. Use caution to prevent tip-overs when moving the cart/apparatus combination.
Avoid installing in confined spaceslike bookcases.
Do not place near naked flame sources, such as lighted candles.
Operating temperature range 5° to 45°C (41° to 113°F).

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community. musictribe.com/support

911 ENVELOPE GENERATOR Controls

Controls ****

T1 (Attack) – Controls the envelope attack time from 2 ms to 10 seconds.
T2 (Decay) – Controls the envelope decay time from 2 ms to 10 seconds.
T3 (Release) – Controls the envelope release time from 2 ms to 10 seconds.
E sus (Sustain) – Controls the sustain time from 0 or 10 seconds.
S-TRIG IN – Connect an external trigger signal via a 3.5 mm TS cable.
OUT – Send the envelope to another module via a 3.5 mm TS cable.

Power Connection

The 911 comes with the required power cable for connecting to a standard Eurorack power supply system. Follow these steps to connect power to the module. It is easier to make these connections before the module has been mounted into a rack case.

Turn the power supply or rack case power off and disconnect the power cable.
Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable.
Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for correct orientation.
After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply

Installation

The necessary screws are included with the module for mounting in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of fixed holes spaced 2 HP apart along the length of the case, or a track that allows individual threaded plates to slide along the length of the case. The free-moving threaded plates allow precise positioning of the module, but each plate should be positioned in approximate relation to the mounting holes in your module before attaching the screws.
Hold the module against the Eurorack rails so that each of the mounting holes are aligned with a threaded rail or threaded plate. Attach the screws part way to start, which will allow small adjustments to the positioning while you get them all aligned. After the final position has been established, tighten the screws down.

Specifications

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Behringer
911 ENVELOPE GENERATOR

FCC STATEMENT

911 ENVELOPE GENERATOR
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation

Important information
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.

Hereby, Music Tribe declares that this product is in compliance with Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC. Full text of EU

DoC is available at https://community.musictribe.com/
EU Representative : Music Tribe Brands DK A/S
Address : Gammel Strand 44, DK-1202 København K, Denmark
UK Representative: Music Tribe Brands UK Ltd.
Address: 8th Floor, 20 Farringdon Street London EC4A 4AB,
United Kingdom

Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center
licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office or your household waste collection service