Music Tribe DM16 12 Input Analog Live and Studio Mixer User Guide

Music Tribe DM16 12 Input Analog Live and Studio Mixer

Product Information

Specifications

• Model: DM16/DM12
• Input: 16/12 analog
• Live and Studio Mixer
• Midas Microphone Preamplifiers
• Version: 2.0

Important Safety Instructions

This product comes with important safety instructions that must be followed to ensure safe usage:

1. Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼” TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.

2. This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.

3. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.

4. To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualified personnel.

5. To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with  liquids, such as vases, shall be placed on the apparatus.

6. These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.

7. Read these instructions.

8. Keep these instructions.

9. Heed all warnings.

10. Follow all instructions.

11. Do not use this apparatus near water.

12. Clean only with dry cloth.

13. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

14. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

15. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

16. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

17. Use only attachments/accessories specified by the manufacturer.

18. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

19. Unplug this apparatus during lightning storms or when unused for long periods of time.

20. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

21. The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.

22. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

23. Do not install in a confined space, such as a book case or similar unit.

24. Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources.
    For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service.

25. Do not place naked flame sources, such as lighted candles, on the apparatus.

26. Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed-of at a battery collection point.

27. This apparatus may be used in tropical and moderate climates up to 45°C.

LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2023 All rights reserved.

LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community.musictribe.com/pages/support#warranty.

Introduction

DM16

DM12

Welcome!
Thank you for purchasing the DDA DM16/DM12 analogue mixing console.
The DM12 and DM16 are classic analogue consoles with plenty of routing options, musical EQ and the smooth, professional sound pioneered by DDA´s sister company, Midas.
These consoles offer plenty of versatility for both studio and live applications, and with proper care and maintenance, you can expect your DDA console to perform faithfully for many years to come.

Features

• Live performance and studio recording analogue mixer with 16/12 input channels
• 12/8 mono input channels with award-winning Midas microphone preamplifiers
• 2 electronically balanced stereo line input channels on 1/4″ TRS connectors
• 3 band EQ on mono channels with swept mid band
• 2 aux sends with pre/post fade switching
• 60 mm precision long-life faders
• Rugged chassis construction for durability in portable applications
• Auto-ranging universal switch-mode power supply
• 3-Year Warranty Program
• Designed and engineered in England

About this manual
This is the operation manual for the DM16 and DM12 analogue mixing consoles. This manual is intended to help get your unit installed and in operation as quickly as possible by giving you unpacking, installation, connection, setting up and operating instructions. To help familiarize you with the DM16 and DM12, there is a description of the controls, along with easy-to-follow user instructions.

Getting Started

This section shows you how to unpack, install, connect up, switch on and configure the DM16/DM12 analogue mixing console.

• This equipment is supplied by a mains voltage that can cause electric shock injury.

Before installing, setting up or operating this equipment, make sure that you have read and fully understand all of this section and the “Important safety instructions” at the front of this manual. Refer to additional safety information on the top cover of the unit.

Unpacking
Carefully unpack your DM16/DM12 analogue mixing console. Then, inspect the console carefully for any signs of damage that may have occurred during transit and notify the courier immediately if you discover any. Check the contents of your DM16/DM12 equipment package. If there are any parts missing, incorrect or faulty, please contact your local distributor or DDA. Please retain the original packing in case you should need to return the equipment to the manufacturer or supplier, or transport or ship the unit later.

Product Usage Instructions

Installation
To install the DM16/DM12 mixer, please follow these steps:

1. Choose a suitable location for the mixer.
2. Ensure that the location is well-ventilated and away from heat sources.
3. Connect the mixer to a MAINS socket outlet with a protective earthing connection.
4. Ensure that all ventilation openings are not blocked.

The position of the console will vary from venue to venue.

When installing the console, take the following into consideration:

• Before installing and operating this Class 1 equipment, make sure it is correctly connected to the protective earth conductor of the mains voltage supply socket outlet through the mains lead.
• When positioning the console for FOH (Front Of House) use it is worth placing the console in a position where the sound system used can be heard properly from the mix position. Try to avoid placing the console behind pillars or large objects, or mixing from a level above the speaker position (for example, from a balcony).
• The console should be located in a convenient space commensurate with the use to which the console is being put.
• Ideally a cool area is preferred, away from power distribution equipment or other potential sources of interference.
• Do not install the equipment in places of poor ventilation.
• Do not install this equipment in a location subjected to excessive heat, dust or mechanical vibration. Allow for adequate ventilation around the equipment, making sure that its fans and vents are not obstructed. Whenever possible, keep the equipment out of direct sunlight.
• Do not place the equipment in an unstable condition where it might accidentally fall over.
• Provision should be made for some flat surface surrounding the console to prevent people using the console as a table top.

Power
The internal power supply is of the switch mode type that automatically senses the incoming mains voltage and will work where the nominal voltage is in the range 100 VAC to 240 VAC.
The correct leads for connection in the area to which the unit was shipped are supplied with the unit. The equipment should only be plugged into the mains outlets using the supplied leads. Make sure the plug fitted on the supplied mains cable is securely fitted to the mains IEC connector on the unit. When fitting or removing a plug, always hold the plug itself and never use the cable, as this may damage the cable. Never insert or remove an electric plug with wet hands.

Handling the equipment
When lifting or moving the equipment, always take its size and weight into consideration. If necessary, use suitable lifting equipment or transporting gear, or sufficient additional personnel. Completely isolate the equipment electrically and disconnect all cables from the equipment before moving it. Do not insert your fingers or hands in any gaps or openings on the equipment, for example, vents.

Electric fields
In accordance with Part 15 of the FCC Rules & Regulations, “… changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.” Should this product be used in an electromagnetic field that is amplitude modulated by an audio frequency signal (20 Hz to 20 kHz), the signal to noise ratio may be degraded. Degradation of up to 60 dB at a frequency corresponding to the modulation signal may be experienced under extreme conditions (3 V/m, 90% modulation).

Top Panel

1. MIC input connects microphones and other balanced signals using XLR connectors.

2. LINE input uses a 1/4″ TRS plug to connect either balanced or line-level unbalanced signals.

3. INSERT jack uses a 1/4″ TRS plug to bring external effects processing (typically compression) into the channel’s signal path. This jack requires specialised insert cables that split into two plugs (either 1/4″ TS or XLR) to access the external unit’s in and out connections.

4. GAIN knob adjusts the sensitivity of the MIC and/or LINE inputs.

5. TREBLE knob adjusts the high frequencies.

6. MID and FREQ knobs adjust midrange frequencies. Adjust the FREQ knob to select the specific frequency adjusted by the MID knob.

7. BASS knob adjusts the low frequencies.

8. AUX 1 and AUX 2 knobs controls the amount of signal sent from each channel to the AUX OUT jacks for monitoring or external effects processing. Use the AUX MASTERS buttons to control whether the AUX channels send a pre-fader signal (PRE) or a post-fader signal (POST).

9. PAN knobs control the left-right stereo placement for each channel.

10. PFL (Pre Fader Listen) button, when pressed, solos the channel and sends the input signal to the MASTER METERS section for more precise gain-setting. In PFL mode, the soloed signal routes to the MONITOR OUT and PHONES outputs, and the PFL LED in the MASTER METERS section will light up.

11. PEAK LED lights when the channel signal overloads.

12. MUTE button mutes the channel.

13. CHANNEL FADERS control the final level for each channel within the overall mix.

14. BAL knob controls the relative left-right balance for stereo signals coming in through the STEREO 1 and STEREO 2 inputs.

15. STEREO 1 and STEREO 2 inputs can be used to route left-right stereo signals into the mix, such as stereo returns from external effects processors. For mono signals, use the L (MONO) input of each pair of stereo inputs.

16. AUX OUT jacks can be used to route AUX mixes out to external effects processors or to stage monitors. For send-and-return effects processing, use the STEREO 1 and STEREO 2 inputs to route the effected “wet” signals back into the overall mix.

17. MONITOR OUT jacks use ¼” TRS plugs to route a copy of the final mix out to local or studio monitors. Control the MONITOR OUT level by using the LOCAL knob in the LOCAL MONITOR section. In PFL (Pre Fader Listen) mode, the soloed PFL signal will override and replace the main mix signal in the MONITOR OUT output.

18. MASTER LEFT and MASTER RIGHT jacks use XLR connectors to send the final stereo mix out to monitors or the main house mix (live sound).

19. MAIN OUT INSERT jacks use a ¼” TRS plugs to apply external effects processing to the final mix before the signal goes out through the MASTER outputs (e.g., to compress the entire final mix). This jack requires specialized insert cables that split into two plugs (either 1/4″ TS or XLR) to access the external processor’s in and out jacks.

20. 2 TRACK uses RCA jacks to route an additional line-level stereo signal into the main mix (MIX button) and/or the MONITOR OUT mix (MONITOR button). Control the level of the 2 TRACK signal by using the volume control on your stereo sound source.

21. RECORD OUT uses RCA jacks to send a line-level copy of the final mix signal out to external recording devices.

22. PHONES jack connects headphones using a ¼” TRS plug. Control the output level by using the PHONES knob in the LOCAL MONITOR section. The PHONES source signal comes from the main mix, except in PFL mode, when the soloed PFL signal will override and replace the main mix signal.

23. +48 V LED lights up to indicate that phantom power has been activated.

24. PHANTOM POWER button turns phantom power on and off.

25. LOCAL knob controls the output level for the MONITOR OUT jacks.

26. PHONES knob controls the output level for the PHONES jack.

27. AUX MASTERS buttons control the pre-fader (PRE) and post-fader (POST) settings for the AUX 1 and AUX 2 knobs.

28. MASTER METERS display levels for the main mix, as well as soloed channels with the PFL (Pre-Fader Listen) function activated for detailed gain-setting. The POW LED lights to indicate that the unit has been powered up. The PFL LED lights up to indicate that the meter is being used for PFL gain setting.

29. 2 TRACK MONITOR button routes the stereo 2 TRACK signal into the MONITOR OUT mix.

30. 2 TRACK MIX button routes the stereo 2 TRACK signal into the main mix.

31. MIX faders adjust the overall output of the mixer at the MASTER LEFT and MASTER RIGHT jacks.
    Rear Panel

32. AC IN accepts the included power cable for connection to a mains outlet.

33. POWER ON switch turns the mixer on and off.

34. SERIAL NUMBER for Warranty registration.

Connectors

To ensure the correct and reliable operation of the equipment, only high quality balanced, screened, twisted pair audio cable should be used. XLR connector shells should be of metal construction so that they provide a screen when connected to the console/snake and, where appropriate, they should have Pin 1 connected to the cable screen.

1. Line output audio connector. Female XLR plug and male XLR chassis connector with the following pinouts: 1 = ground; 2 = hot; and 3 = cold.
2. Mic/line input audio connector. Male XLR plug and female XLR chassis connector with the following pinouts: 1 = ground; 2 = hot; and 3 = cold.
3. RCA connectors (2 track/record out). Male RCA plug and female RCA chassis connector with the following pinouts: 1 = ground; 2 = signal.
4. ¼” TRS jack plug (inserts). Male 1/4″ TRS plug and female TRS chassis connector with the following pinouts: 1 (tip) = send; 2 (ring) = return; 3 (sleeve) = ground.
5. ¼” TRS jack plug (input, output, phones). Male 1/4″ TRS plug and female TRS chassis connector with the following pinouts: 1 (tip) = hot; 2 (ring) = cold; 3 (sleeve) = ground.

Connecting Audio Sources
To connect audio sources to the DM16/DM12 mixer, please follow these steps:

1. Identify the input channels on the mixer.
2. Connect the audio sources to the corresponding input channels.
3. Ensure that the connections are secure.

Operation

Basic Operation

1. Make sure the power to all devices is turned off!
2. Connect all appropriate power and audio cables to the mixer.
3. Set the controls with all knobs centered and all faders down/off.
4. Turn the mixer on.
5. Set the GAIN for each channel. (See the Gain Setting section for details.)
6. With the MAIN MIX faders and LOCAL MONITOR knobs all the way down, turn on your PA system or monitors.
7. Slowly raise the MAIN MIX faders or LOCAL MONITOR knob to the desired level.
8. Adjust the relative level of each channel by raising each CHANNEL FADER.
9. Adjust the left-right position of a channel in the stereo field if necessary by turning the channel´s PAN or BAL knob.
10. For live applications, adjust the overall output from the mixer to the power amp or powered speakers by raising the MIX faders. If the red +10 or +16 LEDs on the MASTER METERS light, lower the MIX faders.
11. Use the AUX 1 and AUX 2 knobs to send the channel signals out to an effects processor or stage monitor connected to the AUX OUT jacks. If used for effects, route the signal back from the processor to the STEREO 1 or STEREO 2 inputs.

Gain Setting

1. Press the Channel 1 PFL (Pre-Fader Listen) button to solo the channel for gain setting using the MASTER METERS. The PFL LED in the MASTER METERS section will light up.
2. Sing, speak or play at a normal level through the microphone or instrument connected to Channel 1.
3. While singing or playing, turn Channel 1´s GAIN control. The MASTER METERS will display the signal level. Set the GAIN control so that the loudest peaks reach 0 on the MASTER METERS.
4. Press the Channel 1 PFL button again to deactivate Pre-Fade Listen mode for that channel.
5. Repeat Steps 1-4 for any other channels that will be used.

Adjusting Levels and Settings
To adjust levels and settings on the DM16/DM12 mixer, please follow these steps:

1. Identify the level and setting controls on the mixer.
2. Use the appropriate controls to adjust the levels and settings according to your requirements.
3. Refer to the user manual for detailed instructions on specific settings and features.

Maintenance and Cleaning
To maintain and clean the DM16/DM12 mixer, please follow these steps:

1. Ensure that the mixer is turned off and unplugged from the power source.
2. Use a dry cloth to gently clean the external surfaces of the mixer.
3. Avoid using liquid cleaners or spraying directly onto the mixer.

Important information

1. Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.
2. Malfunction. Should your Music Tribe Authorized Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfiller for your country listed under “Support” at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at musictribe.com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.
3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Midas
DM16/DM12
Responsible Party Name: Music Tribe Commercial NV Inc.
Address: 122 E. 42nd St.1, 8th Floor NY, NY 10168, United States
Email Address:legal@musictribe.com

DM16/DM12
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Important information:
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with Directive 2014/35/EU,Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Gammel Strand 44, DK-1202 København K, Denmark
UK Representative: Music Tribe Brands UK Ltd.
Address: 8th Floor, 20 Farringdon Street London EC4A 4AB, United Kingdom

FAQ

1. Q: Can I use the DM16/DM12 mixer outdoors?
   A: No, the mixer should not be exposed to rain or moisture. It is recommended for indoor use only.

2. Q: Can I use any attachments/accessories with the mixer?
   A: No, only use attachments/accessories specified by the manufacturer to ensure compatibility and safety.

3. Q: What should I do if the mixer is not operating normally?
   A: If the mixer is not operating normally, refer servicing to qualified service personnel. Do not attempt to perform any repairs yourself.

References

• Music Tribe
• Music Tribe
• Music Tribe
• Music Tribe
• Music Tribe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>