DKS DOORKINGS 1620 1625 Traffic Control Wedge Barrier System Instruction Manual
- July 15, 2024
- DKS DOORKINGS
Table of Contents
1625 TRAFFIC CONTROL
WEDGE BARRIER SYSTEM
1625 WEDGE BARRIER Surface Mount
- Surface mount for quick, easy installation
- Fast speed – raises and lowers in approximately 3.5 seconds
- Simple mechanical linkage to DKS 1602-590 Operator keeps Barrier Arm and Wedge Barrier in sync – no separate motors or hydraulic valves to worry about
- Red (down) / Green (up) LED lighted Barrier Arm for high visibility
CAR RENTAL LOTS • COMMERCIAL AND INDUSTRIAL
TRAFFIC CONTROL • INFRASTRUCTURE FACILITIES • PENITENTIARY
TRANSPORTATION AND SHIPPING
MAXIMUM SECURITY
| | |
---|---|---|---
Fast Raise and Lower of the heavy steel wedge is possible with the use of
precise counter weight| Surface Mount
for quick and easy installation or
where in-ground digging is prohibitive| Lighted Top Arm
for added visibility and safety| Certification
Light Duty Truck: 5,070 lb., traveling at 30 MPH Certification to ASTM F2656-
20 Pending
ACCESS CONTROL SOLUTIONS
TRAFFIC CONTROL WEDGE BARRIER
1602-590 Operator is required. Shown for illustrative purposes only not included with the 1625 Wedge Barrier.
1625 WEDGE BARRIER SURFACE MOUNT
| CLASS OF OPERATION | II, III, IV |
|---|---|
| AVAILABLE LANE WIDTH | 12 Ft (3.66m), clear opening is 11 Ft 8 in (3.55m) |
14 Ft (4.27m), clear opening is 13 ft 8 in (4.16m)
BARRIER ARM| Aluminum with LED Lighting (Red/Green)
ANCHOR POST| 8” x 8” x 1/4” Steel
(203.2mm x 203.2mm x 6.35mm)
54” High + cap (1.37m)
BASE| 12 in. x 58.75 in.
(304.8mm x 1492mm)
1/2 in steel (12.7mm)
16 anchor points
OPTIONS| Red/Green traffic signal
- The 1625 lane barrier is not a stand-alone product. It must be used with a DKS 1602-590 Operator (sold separately).
The 1625 is not crash rated. It is intended to provide a more formidable barrier in conjunction with a standard barrier arm operator system.
The 1625 is ideally used with passenger vehicles and light-duty trucks.
TECHNICAL FEATURES
MECHANICAL
Anchor Plates are 1/2 in (12.7mm) A36 steel
Anchor post assembly are surface mounted and provide 16 anchor points on each
post. The wedge plate has a total of 22 anchor points for an overall total of
54 anchor points for a dependable installation that’s quick and easy.
Wedge barrier is counter-balanced and mechanically linked to the 1602-590
operator. No hydraulics or environmental issues to worry about.
Lane barrier assembly is zinc plated and finished in power-coat full gloss
smooth super polyester
1625 WEDGE BARRIER
Steel wedge barrier and heavy duty steel posts provide a formidable barrier to
help prevent passenger vehicles and light-duty trucks from driving through a
controlled traffic lane, without the expense of bollards, wedges, or crash
beams. (Not crash rated.)
Surface mount (concrete only) for quick, easy installation Integrated lighted
Arm for high visibility Fast speed – raises and lowers in approximately 3.5
seconds
Simple mechanical linkage to DKS 1602-590 Operator
Operator keeps Barrier Arm and Wedge Barrier in sync no separate motors or
hydraulic valves to worry about Actual lane width for 12 ft. unit is 11 ft. 8
in. (3.55m) Actual lane width for 14 ft. unit is 13 ft. 8 in. (4.16m)
Installs for thousands of dollars less than crash rated systems
MISCELLANEOUS
1602-590 Operator is sold separately.
1625 wedge barrier includes linkage hardware and counterbalance weights.
*This Wedge Barrier System is not crash rated. It is intended to provide a formidable barrier to help prevent passenger vehicles and light-duty trucks from driving through a controlled traffic lane. Lane Barrier is not recommended for use in areas subject to freezing weather.
DoorKing,®Inc.
Access Control Solutions since 1948
120 S. Glasgow Avenue,
Inglewood, California 90301 U.S.A.
Tel: 310-645-0023 FAX:
310-641-1586
www.doorking.com
© 2024 All Rights Reserved.
Product specifications may change without notice. Rev. 6/24
MEMBER:
DISTRIBUTED BY:…………………..
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>