AUFOCUS XMZHTB1 Pro 2kw Bluetooth Diesel Heater Instruction Manual

AUFOCUS XMZHTB1 Pro 2kw Bluetooth Diesel Heater Instruction Manual

XMZ-HTB 1 pro Operation Instructions

Working mode:

1. In gear mode, the gear can be adjusted within the range of 1 to 10 gears;
2. In temperature control mode, the set temperature can be adjusted within the range of 8~36 °C. The gear of the control switch changes with the temperature inside the cab. When the temperature rises or falls, the control switch will automatically adjust the operating gear to quickly reach the set temperature, making the heater run more intelligent and economical.
3. When a fault occurs during operation, the control switch will display a flashing window to display the fault code, making it easier to find the fault more accurately and intuitively.

Operating instructions:
On/off and mode switching: Press the when it is turned on; Press the knob 【 ON/OFF】 button to turn on the device in the off state; Press the 【 ON/OFF】 button to turn off the device to switch the current gear/temperature control mode/constant temperature heating/ Ventilation mode

• Gear ad adjustment: Rotate the 【 knob 】 clockwise to run gear/temperature+1, up to 10 gears/36 ℃, rotate 【 knob 】 counterclockwise to run gear/temperature -1, down to 1 gear/8 ℃;

• Basic settings : After turning on the computer, press and hold 【 O N / O F F 】 for 3 seconds to enter the basic settings interface. The setting item’s displayed in the upper left corner, and the interface displays the specific data under the setting item:
  F 0: Current time
  F 1: Self start time
  F 2: Running time 【 After self start 】
  F 3: Self start switch setting
  F 4: Language switching [Chinese (C), English (E), Russian (R), voice off (–)] F 5: Temperature compensation
  F 6: Fuel tank volume [5-50L (switch unit 5L) (default 10L)] [Display – represents not monitoring fuel tank condition] F 7: Fuel pump type [16/22/28/32 UL (default 22 UL)] F 8: Constant temperature heating (in temperature control mode, when the cab temperature reaches the set temperature, it will automatically shut down after a delay o f 30 seconds; when the cab temperature is 2 ℃ lower than the set temperature, it will automatically start up after a delay o f 30 seconds)
  F 9: Temperature switching (℉/℃)
  F A: Screen brightness;
  F b: Full fuel tank
  FC: CO value detection (this function is used with CO sensor )

  • Press the 【 knob】 tomake modifications, and press the 【 knob 】 again to confirm the current data modification;
  • Rotate the 【 knob】 to adjust the settings. After all adjustments are successful, press the 【 knob】 for 3 seconds to save all basic settings;

• Engineering mode: Press the 【 knob 】 for 5 second sin the startup state to enter engineering mode. The current project will be displayed in the upper right corner and the interface will display specific data under the project. Rotate the 【 knob】 to adjust the project check View data:
  En 00: heater motherboard version number [scrolling display];
  En 0 1: Fault code;
  En0 2: Shell temperature;
  En0 3: Power supply voltage;
  En0 4: Heater operating gear;
  En0 5: cab temperature;
  En0 6: Altitude;
  En0 8: Remote control matching;
  En0 9: Bluetooth matching;

• Quick remote control ma tching: In the shutdown sta te , continuously pre ss the knob twice ; Enter the En08 interfac e, which displays “rte” .Lan guage 【knob】for 3 seconds to start matching, and the screen displays；
  At this point, click on the remote control and add a key to match successfully, and return to the running interface;

  • Clear last remote control matching data: During power on self-test, press and hold the ON/OFF】 button, and the interface will display “C clearing. When the interface displays “SU C”the clearing is successful.

• Bluetooth matching: open the mobile phone applet, click the setting key, set the 4-digit password, and then adjust the switch to enter the engineering modeEn09, and the interface displays “BLe”, and the Bluetooth name is displayed on the upper right side of the screen,
  Press and hold the 【 knob 】 for 3 se conds, and the upper right corner will change from fla shing the original pa ssword to displaying the se t password,and the interfac e display will change to “SUC”. After successful matching, it will automatically return to the running interface;

• Pump oil mode : Pre ss and hold the 【 knob 】 for 5 seconds when the powe r is turned off for the first time , until the screen fla shes and the countdownstartsfor 300 seconds. After the countdown ends, the pump oil will automatic ally exit or pre ss 【 O N / O F F 】 to end the pump oil and shut down;

• Check CO, detection value: Press and hold the power on button while turning on the machine; (This function is used with CO sensors)

• Fault display: When the heater malfunctions, the display area flashes a fault code, and the fault type is shown in the table below;

the actual vehicle voltage; Check if the power supply voltage of the 24V version is higher than 32V or lower than 18V; 12V version;Check if the power supply voltage is higher than 18V or lower than 9V; Check if there is any looseness or virtual connection at the main harness connector;
E-03| Abnormal ignition plug| Check if the ignition plug is connected improperly, Igniter plug malfunction, replace the ignition plug; Main board malfunction, replace the main board;
E-04| Abnormal oil pump| Check if the oil pump plug is loose or connected in a virtual manner; Check if there is an open circuit in the main harness; Oil pump malfunction, replace oil pump;
E-05| Overheat protection| The furnace temperature sensor model is incorrect or faulty, replace the sensor; Main board malfunction, replace the main board;
E-06| Fan  abnormality| Check if the fan impeller is stuck; Check if the fan plug is loose or connected improperly; Fan malfunction, replace the fan;Check if the induction magnet of the wind turbine is missing or has incorrect polarity; Check if the motherboard wind speed sensor is functioning properly; Main board malfunction, replace the main board;
E-08| Lack of fuel and stalling| Check if the fuel tank is short of oil;
E-09| Overheat protection sensor| Check if the temperature sensor connector is loose or poorly connected; Sensor malfunction, replace the motherboard; Main board malfunction, replace the main board;
E-10| Secondary startup failure| Check if the oil pump is working; Check whether the interfaces of the oil circuit are waxed or blocked;

WeChat Mini Program Apple (IOS) APP

Search for airHeaderBle’ o n t h e APP Store

Android APP

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>