DOMETIC CapTouch Marine Cabin Control Instruction Manual

DOMETIC Cap Touch Marine Cabin Control Instruction Manual

Important notes

Please read these instructions carefully and follow all instructions, guidelines, and warnings included in this product manual in order
to ensure that you install, use, and maintain the product properly at all times. These instructions MUST stay with this product. By using the product, you hereby confirm that you have read all instructions, guidelines, and warnings carefully and that you understand and agree to abide by the terms and conditions as set forth herein. You agree to use this product only for the intended purpose and application and in accordance with the instructions, guidelines, and warnings as set forth in this product manual as well as in accordance with all applicable laws and regulations. A failure to read and follow the instructions and warnings set forth herein may result in an injury to yourself and others, damage to your product or damage to other property in the vicinity. This product manual, including the instructions, guidelines, and warnings, and related documentation, may be subject to changes and updates. For up-to date product information, please visit documents.dometic.com.

Explanation of symbols and safety instructions

This manual has safety information and instructions to help you avoid or reduce the risk of accidents and injuries.

Explanation of symbol

A signal word will identify safety messages and property damage messages, and also will indicate the degree or level of hazard seriousness.

DANGER!
Indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING!
Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION!
Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
NOTICE!
Indicates a situation that, if not avoided, can result in property damage.
NOTE Supplementary information for operating the product

Supplemental directives

To reduce the risk of accidents and injuries, please observe the following directives before proceeding to install and operate this appliance:

• Read and follow all safety information and instructions.
• Read and understand these instructions before installing this product.
• The installation must comply with all applicable local or national codes, including the latest edition of the following standards:

U.S.A.

• ANSI/NFPA70, National Electrical Code (NEC)
• ANSI/NFPA1192, Recreational Vehicles Code

Canada

• CSA C22.1, Parts l and ll, Canadian Electrical Code
• CSA Z240 RV Series, Recreational Vehicles

General safety messages

WARNING! ELECTRICAL SHOCK, FIRE, AND/ OR EXPLOSION HAZARD. Failure to obey the following warnings could result in death or serious injury.

• Use only Dometic replacement parts and components that are specifically approved for use with the appliance.
• Avoid improper installation, adjustment, alteration, service, or maintenance of the appliance. Service and maintenance must be done by a qualified service person only.
• Do not change this product in any way. Modification can be extremely hazardous.
• This product should be installed in a controlled, indoor environment

Intended use

The Cap Touch control is a user-friendly capacitance touchscreen display for basic
thermostat operation. The micro controller-based unit is designed for use with direct expansion (DX), reverse-cycle air-conditioning systems, and chilled- water systems (CW). The display panel has 34 programmable parameters, automatic and manual fan speeds, standard and optional sensor inputs, and fits both Vimar® Idea and Eikon switch bezels.

• Faulty assembly or connection.
• Damage to the product resulting from mechanical influences and excess voltage.
• Alterations to the product without express permission from the manufacturer.
• Use for purposes other than those described in the operating manual.

Dometic Corporation reserves the right to change appearances and specifications without notice.

General information

This section provides information on the tooling, parts, and display features for the Cap Touch control.
NOTE The images used in this document are for reference purposes only. Components and component locations may vary according to specific product models. Measurements may vary ± 0.38 in (± 9.7 mm).

Tools and materials

Dometic recommends that the following tools and materials be used while installing the appliance:

Recommended Tools

Phillips-head Screwdriver
Recommended Tools

Safety Glasses
Saw
Included Parts| Quantity
---|---
Screws| 4
Cap Touch Control| 1
Additional Parts| DX| CW
---|---|---
Required for CW Installations (not included)
Water Inlet Temperature Sensor| | X
Optional Parts
Outside Air Temperature (OAT) Sensor| X| X
Inside Air Temperature Sensor| X| X
Auxiliary Electric Heater| X| X
Room Temperature/Relative Humidity Combination Sensor| X| X
Seawater Low-Limit Temperature Sensor| X|
Pump Sentry Water Sensor| X|

NOTE The maximum length for the display and sensor cables is 75  (22.86 m).
NOTE Additional parts are not included with the standard control package

Display features

This section explains the function of the icons on the Cap Touch display.

water tempera- tures, as selected.
Icon| Name| Function
---|---|---
****| Mode Indicator| Indicates the current display mode.
****| HVAC Mode|

• Cycles through the
  different modes.

• Sends the display to sleep if held for three seconds.

Specifications

The following table lists the Cap Touch control dimensions, cable lengths, system inputs, and operational specifications.

Product dimensions

Display Panel Dimensions for the Eikon Bezel| 4.5 in × 2.9 in (114.3 mm × 73.66 mm)
---|---
Cut-Out Dimensions for the Eikon Bezel| 1.90 in × 2.80 in (48.26 mm × 71.12 mm)

Cable length

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>