SPYPOINT FORCE-48 Trail Camera User Guide
- July 10, 2024
- SPYPOINT
Table of Contents
SPYPOINT FORCE-48 Trail Camera
Specifications
- Model: FORCE-48
- Power Source: 12V or 8AA alkaline/lithium batteries
- SD Card Compatibility: 2GB to 512GB
- Resolution: 30 MP
Product Usage Instructions
Power Source Selection
Select either a 12V power source or 8AA alkaline/lithium batteries for operation. You can use a combination, with the camera prioritizing 12V first.
Installing an SD Card
Insert an SD card with a memory capacity between 2GB and 512GB into the designated slot on the camera.
Operating Modes
OFF: Camera is off.
SETUP: Access and adjust camera settings.
ON: The camera is in detection mode. Red light flashes for 30 seconds
before becoming ready for use.
Charging Instructions
Charge the camera for approximately 12 hours using the provided charging cable before initial use. Check battery status in SETUP mode.
Formatting SD Card
After inserting the SD card, format it by navigating to the Format option in the settings menu. Follow on-screen prompts to complete the formatting process.
General Settings Setup
Access various camera settings by switching to the LCD and navigating through options using the buttons. Use OK to confirm selections.
Operation
Once setup is complete, switch the button to ON for operation. You can also switch to OFF and turn on the camera later as needed.
Red Light Indicators
In SETUP mode, the red light confirms motion detection adjustments. When switched to ON, the red light flashes for 30 seconds before the camera is ready for use.
IN THE BOX
NOTE
Batteries are sold separately.
User Manual, software updates & FAQs are available at:
www.spypoint.com/support.
COMPONENTS
- No glow flash
- Red LED indicator
- Photo lens
- Detection lens
- Cable lock hole
- Slot for installation strap
- Locking latch
- 12 V jack
- Screw-thread for standard 1⁄4”-20
- LCD screen
- OK button
- Switch ON/SETUP/OFF f Navigation buttons SD card slot
- Battery compartment
PREPARATION
SELECT A POWER SOURCE
You can use any combination of the above power sources with your FORCE-48. If multiple power sources are connected, the camera will use them in the following order: 12V, and then the AA.
FOR MAXIMUM PERFORMANCE ND WITHOUT LEAKING BATTERIES
- Use new batteries.
- Use ONLY alkaline or ONLY lithium batteries.
- Do not mix new and old batteries.
- Do not use rechargeable AA batteries, as their lower voltage may cause operating difficulties.
INSTALLING AN SD CARD
The camera was designed to operate with an SD card between 2 and 512 GB of memory.
INSERT AN SD CARD
- Make sure the camera is turned OFF.
- Locate the SD card slot. It is on the bottom right corner of the camera (see diagram).
- Insert an SD card (up to 512 GB) in the slot and make sure to respect the direction indicated in the diagram.
The card is inserted correctly when a click is heard.
FORMAT YOUR SD CARD
After inserting your SD card, you will need to navigate to the Format option
in the settings. Use the onscreen prompts to format the SD Card.
GENERAL SETTINGS SETUP
Use the 
buttons to
switch to the LCD display or to change options, and press OK to select.
Several setup pages will be displayed.
- To turn the camera ON/OFF, use the ON/SETUP/OFF switch.
- The switch must be on SETUP to make your initial changes.
- When the switch is on SETUP, press OK to open the MENU:
- Set the language (English, Français, Deutsch)
- Set the date (MM/DD/YY or DD/MM/YY)
- Set the time (12h or 24h)
- Set the temperature (°F/ °C)
SETUP
ADJUST THE SETTINGS FOR THE 3 MODES OF OPERATION
PHOTO MODE
-
Delay: Allows you to select the time elapsed before the camera can detect again and take the next photo.
If you want to capture multiple photos, use a shorter delay. Once you have selected the delay, press OK. -
Quality: Allows you to select a resolution of 2MP, 8MP, 16MP, 30MP or 48MP. Once you have made your selection, press OK.
-
Multi: Allows you to select the number of photos to be taken per shot (from 1 to 5 photos). Once you have made your selection, press OK.
-
Detect: Allows you to set motion-detector sensitivity (LOW, NORMAL, HIGH, AUTO). Once you have made your selection, press OK.
VIDEO MODE
- Delay: Allows you to select the time elapsed before the camera can detect again and take the next video.
- Quality: Allows you to choose between 480P and 720P.
- Once you have made your selection, press OK.
- Length*: Allows the user to choose the video length (10 to 60 s). Once you have made your selection, press OK.
- Detect: Allows you to set motion-detector sensitivity (LOW, NORMAL, HIGH, AUTO). Once you have made your selection, press OK.
TIME-LAPSE
Allows you to take photos at regular predefined intervals without necessarily detecting a movement.
OTHER OPTIONS
- Night: Choose the BOOST option for maximum brightness at night, select OPTIMAL to reduce fuzziness at night, and MIN BLUR to minimize the blurriness of moving objects. Once you have made your selection, press OK.
- Name: Allows to give a name to your camera.
- About: Indicates the software version.
- Default: Resets all default settings
- Format: Allows the camera to format the SD card the next time it is used. (Reformatting the SD card will delete all photos and videos on the card. Only format the card if you are sure you want to delete everything on it. Transfer all data to your computer beforehand).
OPERATION
Once the setup is complete, turn the button from SETUP to ON. You may also switch from SETUP to OFF and turn the device ON later.
RED LIGHT ON THE FRONT OF THE CAMERA
When the switch is in the SETUP position, the red light will flash to confirm
a motion detection once you have adjusted your settings.
When you move the switch to the ON position, the red light at the front of the
camera will flash for 30 seconds to allow you to move out of the camera’s
field of view.
When the light turns off, the camera is ready for use.
INSTALLATION
Recommended height of installation:
The camera must be installed at the height of the center line of the animal’s
body.
Ideal setup for high-quality images and videos:
The target animal should be 7.5 m from the camera to get a better line of
sight.
To produce brighter photos at night, there should be items reflecting the
camera’s flash in the background.
Please note that the camera should never be directly pointed at the sun to
avoid backlighting and faulty detections.
Manufactured By
Scan for detailed instructions, LED light pattern descriptions, complete user
manual & other helpful information:
spypoint.com/force48-guide
Need assistance? Just contact us!
INTERNATIONAL
spypoint.info/en/support-2/
+49 (0) 36331-403333
CAN/US
spypoint.com/support 1-888-779-7646
2-year limited warranty, visit
spypoint.com/garantie for complete details.
Made in China
FAQ
Q: What should I do if the camera does not detect motion?
A: Check that the camera is in ON mode and that the detection settings are properly configured in SETUP mode. Also, ensure that the camera has a clear line of sight.
Q: How do I update the camera software?
A: Visit www.spypoint.com/support to access software updates and follow the provided instructions for updating your camera’s software.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>