BINCOLOR BC-355RF LED Controller User Manual

BINCOLOR BC-355RF LED Controller

Brief Introduction

• Welcome to use this RGBCCT controller, which is a universal high-performance, overall color-changing power controller.
• It can be applied to RGB_CCT constant voltage full-color lighting products with co-anode, such as LED modules, LED light strips, SMD soft light strips, and other LED lamps.
• All of its functions can be operated by the remote control.

Specifications

Features

1. Automatically adapt DC12V-48V input voltage.
2. Conveniently controlled by OLED screen, encoders, and buttons.
3. Friendly to human eyes and users can DIY any color they want.
4. Preset scenes and one-click restore are supported.
5. Amplified with power repeater.
6. It will automatically return to the operating state before the power-off with power-down protection after an unexpected power-off.

Safety warnings

1. For your safety, please read the manual carefully before installation.
2. Do not install this controller in lightning, intense magnetic, and high-voltage areas.
3. Fixed it properly to reduce the risk of component damage and fire caused by short circuits.
4. Put the controller in a place of well-ventilated and moderate temperature.
5. Make sure to use the right voltage and power adapter (please select DC12-48V power supply with constant voltage)
6. Do not connect cables when powered on; make sure of a correct connection and power on after no short circuit is examined.
7. Do not disassemble the controller when problems occur, please contact the supplier.

Dimension

Instruction

1. Instruction
   • The controller has three states: off-screen state, normal state, and adjustment state.
   • In the screen-off state, press any button to switch to the normal state, and the normal state shows the output state of the current light.
   • Press any button again in the normal state to switch to the corresponding adjustment interface or directly call up the corresponding scene.
   • Note: The adjustment state will switch to the normal state without any operations after 30 seconds, and the normal state will switch to the screen-off state without any operations after 30 seconds.
2. Use the encoder to adjust the color of each channel:
   • Increase or decrease the greyscale level of the channel by rotating the knob, and switch the channel by pressing the knob.
   • As shown in the picture, the grayscale value of the G channel is being adjusted:
   • Note: For better user experience, the quick adjustment mode can be activated by rotating the knob in the same direction for more than 2 seconds and releasing the knob less than 0.8 seconds during the rotation.
3. Save/Call scene mode
   • Thine the le preen shows, lave rese to button to the scene is saved) and short press the Scene button to call up the scene.
   • As shown in the picture, the current light effect is saved to “Scene 1”:
   • As shown in the picture, the “Scene 1” scene mode is called up.
   • Note: Calling up the scene will override the current light state.
4. Conjunction diagram
   • Conjunction diagram of LED constant voltage strip
5. Remote control operation
   • Remote control matching:
   • In the normal state or adjustment state, long press the encoder to enter the remote control pairing interface, and press any button to exit the pairing interface.
   • Press any button of the remote control under this interface, and when the controller OLED displays the ID of the remote control and “Success”, the remote control is successfully paired.
   • As shown in the picture:
   • Note: The controller can be paired with only one remote control, which means that after it is successfully paired, the new remote control will overwrite the previous one.

Keys and Functions

Keys and functions of the remote control:

Note:

• If a certain type of light (RGB or CCT) is turned off when the scene mode is called up, the light channel of this type needs to be reopened to continue to dim.
• The scene button does not distinguish the type of remote control, that is, when saving the scene effect, the status of RGB and CCT will be saved at the same time, and the current state of RGB and CCT will be overwritten at the same time when calling up.

Touch circle:
Click or touch the circle to change the color of the corresponding channel for the current remote control type (RGB or CCT).

Mode button dynamic/static mode changes:

• The remote dynamic mode is shown as follows:
• The remote dynamic mode is shown as follows:
• RGB static color display: Static Color. Dynamic display: M: 10 S: 8 B: 8, which refers to the mode number, speed value, and brightness value.
• CCT static color display: Static Color. Dynamic display: Fade S:8 B:8, which refers to the color temperature gradient, speed value, and brightness value.
• Note: For the RGB type, a total of 10 dynamic modes are supported, of which the tenth is called up by long pressing the MODE button after switching the remote control type to RGB. SPEED and BRIGHT in MODE10 are determined by SPEED and BRIGHT set by MODE 1 -9. For the CCT type, only gradient dynamic mode is supported.

Dynamic modes:

adjustable
5| Full color smooth| All ?-color gradual changes| Brightness, speed adjustable
6| Red-green smooth| RG 2-color gradual changes| Brightness, speed adjustable
7| Red blue smooth| RB 2-color gradual changes| Brightness, speed adjustable
8

9

| Green blue smooth

Whites smooth

| GB 2-color gradual changes White gradual bright & fade| Brightness, speed adjustable Brightness, speed adjustable
10| Cycle mode| All changing modes overlap the cycle| Brightness, speed adjustable

Exception Handles

connection
3. Wrong or loose connection| 3. Check connection
Wrong color| 4. R, G, B, W, CW wrong wiring| 4. Re-wire R, G, B, W, CW
Brightness of the

LED is not even

| 5. Output wire too long, voltage drops| 5. Reduce cable or use loop connection
6. Wire diameter too slim, voltage drops| 6. Calculate the current and change to a wider wire
7. Power supplier overloads| ?.Change to another large power supplier
8. Controller overload| 8. Add a power repeater
Mode not change| 9. The setting of speed is too low| 9. Press the button to increase speed
Can’t be remotely controlled| 10. The battery has run down| 10. Change battery
11. Out of the controlling distance| 11. Shorten the controlling distance

After Sales
This controller is covered by a 3-year warranty from the day you purchase our products,

we provide free repair or replacement services except in the following cases:

1. Any defects caused by wrong operations.
2. Any damages caused by inappropriate power supply or abnormal voltage.
3. Any damages caused by unauthorized removal, maintenance, modifying circuit, incorrect connections, and replacing chips.
4. Any damages due to transportation, breaking, or flood water after the purchase.
5. Any damages caused by an earthquake, fire, flood, lightning strike, etc force majeure of natural disasters.
6. Any damages caused by negligence, inappropriate storing at high temperature and humidity environment, or near harmful chemicals.

WARM TIPS

Power Source Selection:

• The power source must be a DC constant voltage type of power supply.
• Due to the efficient output in some power supplies is only 80% of the total, so please select at least 20% higher output power supply than the consumption of LED lights.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>