GARAGE STOP RQBK10 2 for Chamberlain Liftmaster Craftsman Garage Door Opener Remote Instruction Manual

GARAGE STOP RQBK10 2 for Chamberlain Liftmaster Craftsman Garage Door

Opener Remote

Specifications

• Product Model : RQBK10
• Remote Control Type : Replacement
• Battery Type: CR2032 3V

Product Usage Instructions

1. Step 1: Locate the Learn button on the garage door opener and confirm the color.
2. Step 2: Press and hold the program button on the remote control until the LED flashes 4 times and turns off.
3. Step 3: Press the remote control button the specified number of times based on the color of the Learn button.
4. Step 4: To exit programming mode, press any button except the one just programmed.
5. Step 5: Press and release the Learn button on the garage door opener within 30 seconds.
6. Step 6: Press and hold the remote control button until the garage door opener lights flash or two clicks are heard.

How to Use the Remote Control

Press and hold the button until the door or gate starts to move. Avoid releasing the button to prevent accidental presses.

Troubleshooting

• Solution 1: Ensure the garage door is closed before programming.
• Solution 2: Try programming with a different button on the remote.
• Solution 3: Stay close to the garage door opener during programming.
• Solution 4: Clear the memory of the opener if full and reprogram.
• Solution 5: For specific models with red or orange buttons, follow alternative programming solutions.

Battery Information

For battery replacement, follow these guidelines:

• Ensure correct installation according to polarity (+ and -).
• Do not mix old and new batteries or different types.
• Recycle or dispose of used batteries properly.

Frequently Asked Questions (FAQ)

• What should I do if programming fails?
  If programming fails, refer to the original manual of the garage door opener for guidance.

• How can I clear the memory of the garage door opener?
  To clear the memory, press and hold the Learn button on the garage door opener until the LED turns off and then release.

• What battery type does the remote control use?
  The remote control uses a CR2032 3V battery. Follow proper disposal guidelines for used batteries.

Note: The remote control is not original remote control, it is just a replacement. When programming the remote control, please carefully read the following manual and watch the programming video.

Programming steps

• Step 1: Locate Learn button on the garage door opener. And confirm the color. The learn button has 5 colors:
  The learn button has 5 colors: Yellow,Purple,Red,Orange,Green

• Step 2: Press and hold the program button at the same time the remote control until the LED on the front of the remote control turns on,then flash 4 times and off. Now turn to step 3 quick.

• Step 3: Press and release the remote control button you wish to use the number of times that corresponds with the garage door opener type:

Color of opener

learn button

| Press

times

---|---
Yellow| 1
Purple| 2
Red / Orange| 3
Green| 4

• Step 4: To exit programming mode,press any remote control button except the button that was just programmed.

• Step 5 : Press and release the Learn button on the garage door opener. The Learn LED will light. Within 30 seconds…

Attention:

  * Step 5, please refer to the programming method in the door opener manual.
  * Some door openers,such as model LiftMaster 8500 \Chamberlain RJO20 RJO70 RJO101 , Press the door control panel LEARN button twice, and the red learn LED will turn on.

• Step 6: Press and hold the remote control button programmed in step 3 until the garage door opener lights flash or two clicks are heard.

HOW TO USE THE REMOTE CONTROL

• Press and hold the button down until the door or gate starts to move.
• Do not release the remote button at once(Avoiding accidental button presses).

Troubleshooting

• Solution 1: Your garage door must be closed before you start to program remote, otherwise programming maybe failed.

• Solution 2:Try to program the remote using other button of the remote.

• Solution 3: Please first get close to garage door opener when you program remote.

• Solution 4: Maybe the memory of the opener is full, please clear it then program again.
  Method: Press and hold the learn button on garage door opener for several seconds until LED off then release.Then all memory is cleared.
  Note:The old remote will also be cleared, please program again.

• Solution 5: For some garage door opener with the red or orange learn button,such as mode is 41A5021 or 41A5483,please choose one of the following solutions：

1. Try to select the Yellow learn button type;
2. please first erase all receiver codes,then continue to program the remote.

• Solution 6: If you think your opener’s learn button is red, but it can’t program successfully by using red learn button type, maybe it has a possibility:
  The color ofthe learn button is fraded,It maybe purple learn button.Please try to program the item by using purple learn button type.

• Solution 7: Attention:For programming step 5, please refer to the programming method in the door opener manual. Some door openers,such as model LiftMaster 8500\Chamberlain RJO20 RJO70 RJO101 , in step 5 of programming, Press the door control panel LEARN button twice, and the red learn LED will turn on.

BATTERY

Pry open the case first in themid dle, then at each side with the visor clip.

• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
• Even used batteries may cause severe injury or death.
• Call a local poison control center for treatment information.
• The compatible battery type CR2032 3V.
• Non-rechargeable batteries are not to be recharged.
• Do not force discharge, recharge, disassemble, above 60°C/140°F or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.

When replace the battery ,please notice as below:

• Ensure the batteries are installed correctly according to polarity (+ and-).
• Do not mix old and new batteries, different brands or types of batteries,such as alkaline, carbon-zinc,or rech argeable batteries.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>