CUBE-BABY 2ARCP Bluetooth Receiver User Manual
- July 8, 2024
- CUBE-BABY
Table of Contents
CUBE-BABY 2ARCP Bluetooth Receiver User Manual
CUBE BABY is a kind of portable and multifunctional bass guitar effect. It presets three sets of original tones from the factory, the users can edit the tones and save them, and the method of operation is simple and intuitive. This effect has a built-in battery, which solves the problem of long-distance power supply. CUBE BABY contains 9 classic IR, two effects of nodulation (chorus, phase shift), one tape delay, one reverb effect, eight classic IR box models, and a high precision audio radiance. Besides, CUBE BABY is also equipped with a recording function on mobile phones, wireless music playback, and an audio interface. It integrates a variety of effects and functions in one, small size, good performance, portable, and excellent sound! It could be a good partner for your guitar.
The power supply
- It is equipped with a built-in battery for power supply, which can last for 6 hours after a full charge.
- It can be directly used to power the device by mobile phone charging power supply or charging treasure. It supports charging/electricity simultaneously.
- The charging time depends on the output power of the charging transformer. For example, the charging head with an output power of dc5.0v / 2.0A can be fully charged within 2 hours when the built-in battery is exhausted.
Effects module link
Tuner → Pre-Amp → Modulation effect → Delay effect → Reverb effect → IR CAB
Rear panel
- DIN: Used to connect signal input of guitar.
- Power switch
- BUSB port: Used to charge, built-in USB audio interface function. It can be connected to the computer for recording playback, support computer software import third-party IR CAB.
- Mobile phone port: Used for recording and playback of mobile phones.
- Headphone output: Connect to the listening headphone.
- OUT: Mono output, connected to a speaker or mixer.
Front panel
- TYPE: Select a different type of tone
- GAIN: Distortion gain knob
- STONE: Tone Brightness Knob
- MOD: PHASER/CHORUS effect knob
- STIME: Delay time button
- OFB: Feedback knob
- MIX: Dry and wet ratio knob
- REVERB: Reverb knob
- IR CAB: Box simulation
- VOLUME: Output volume knob
- Wireless accompaniment light
- Wireless music playback light
- Charging light
- C function foot switch
- B function foot switch
- A function foot switch
Effect module
AMP IR timbre module
TYPE knob: select the TYPE of IR. Please refer to the following list for
specific TYPE.
DELAY module
- TIME Knob: Control the delay time.
- FB Knob: Control feedback size.
- MIX Knob: Adjust the wet/dry ratio, and turn the MIX knob to the far left to turn off delay, the knob indicator lights off.
REVERB module
REVERB Knob: Turn to the far left to turn off, at which point the knob light
goes out. The amount of reverb to the right gradually increases. The REVERB
knob light goes out when the REVERB module is turned off.
IR module
IR CAB knob: A total of 9 gears, the first gear is closed, 2 to 9 gears are 8
different sizes of the box, the following table is the factory preset box.
CUBE BABY allows users to load third-party IR, using the USB cable that comes with the product to import third-party IR box simulation files via the manufacturer’s free software cube- suite online computer. Users can import IR files that cover the original factory for the loading location of the list above. When the original IR documents are covered and replaced, they cannot be recalled, please be careful before doing so.
TUNER Module
CUBE BABY contains a highly sensitive tuner, which is used as follows; Long
step combination foot nail “B+C” into TUNER tuning mode, the tuning meter
using the parameter knob light on the host panel to display the tuning of the
tone and instant pitch, please see the illustration: After tuning, press any
pin to exit TUNER mode.
Wireless accompaniment input function
CUBE BABY includes wireless music playback, which allows users to play
accompaniment during practice or performance, and long-term stepping on the
combination of “A+B” to turn on successfully, the light lights up blue. Press
the “A+B” pin again until the light goes out to exit this function.
Mobile recording function
CUBE BABY includes high-quality phone recording capabilities that connect the device’s phone socket to your phone/tablet via a random internal recording dedicated cable, and enable high-quality recording using your phone/tablet recording software.
LIVE/PRESET Mode
CUBE BABY has two modes of operation, LIVE for real-time editing mode and
PRESET mode. The initial power-on default enters PRESET mode, short press the
combination nail “B+C” for LIVE PRESET mode switching.
LIVE Mode
In LIVE mode, the “A/B/C” function pin is responsible for turning the
corresponding effect module on/off, and the corresponding function light is
always on or off. In LIVE mode, the user can edit the tone effect chain and
hold the pin for a long to save.
PRESET Mode
- this effect device for the user presets three classic tones for the factory tone;
- In PRESET mode, use the A/B/C function to pin to select the factory tone or the user saves the tone.
- Unlimited switching between preset three sets of tones, with the staple indicator for the selected tone flashing.
How to edit a tone
- Power-on initialization; when the built-in battery is fully charged or the power supply USB cable is connected, please turn off the power switch. At this time, the parameter button turns on from left to right and then from right to left to self-test. After the host self-test is completed, the system defaults to the PRESET mode. The tone on the current A / B / C pedal becomes the factory tone.
- Press the B and C pedals at the same time to switch to LIVE mode. Then, please check whether all the parameter buttons are turned off. Turn the VOLUME to the appropriate level, and the output volume should not be too high, which will avoid damage to the connected speaker equipment.
- To start editing the tone, press the C foot switch to open the Become tone module, set the TYPE button to the 7th position (please refer to the Become data sheet for item 1 of question 4 in this guide), and select the distorted tone named Cali JP B. Next, turn the GAIN distortion gain button to the 3 o’clock position and select the brightness of the tone you want.
- I set the TONE parameter to the noon position of the clock (the users can evaluate the distortion gain and tone brightness parameters that are needed).
- Next, we step on the B foot switch to turn on the MOD and DELAY modules. Because I expected to adjust a relatively pure distortion SOLO tone, I did not consider the effect of using MOD. Please turn the MOD knob to the clock at noon. The MOD effect is turned off, and the knob indicator is turned off. Then turn the MIX button to turn on the DELAY effect. Turn the MIX knob to the 9 o’clock position, the FB knob to the 11 o’clock position, and the TIME button to the 2 o’clock position. I need this tone with sufficient delay effect so that I can play more smoothly with slower phrases.
- Next, we will on the A pedal to turn on the REVERB and IR CAB modules. Please adjust REVERB to the 11 o’clock position to make this tone reflect more space. Then I moved the IR CAB knob to the seventh position, and I chose a Soldano 2X12 cabinet.
- Next, we need to adjust the output volume of the edited tone. I set the VOLUME knob to the 1- point position of the clock. (it is recommended that you set the output volume value of the VOLUME knob according to your needs)
- When it is determined that the tone has been edited and the output volume is adjusted, we can save the edited tone in the PRESET mode, so that we can call the edited tone at any time when playing. Please select the stud positions you want to store (this effect supports the storage of three tones, which, are the A / B / C stud positions in the preset mode). Here I choose the A stud positions and long A stepping on the nail, the prompt of A stepping on the foot switch will flash quickly, indicating that the tone is being stored until the flashing stops and the tone has been stored.
- At this time, the tone that was just edited has been successfully stored in the PRESET mode, covering the tone preset by the factory in the A-stamp. We stepped on the B and C at the same time to switch from the LIVE mode to the PRESET mode. Step on the A pedal to find the Cali JP B distortion solo sound you just saved.
Technical parameters
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Download PDF: CUBE-BABY 2ARCP Bluetooth Receiver User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>