ELITE PROAV Pro Series Tripod Tab Tension User Guide

Tripod Tab-Tension Pro Series
Portable Tripod Tab-Tensioned Projection Screen For models: CineWhite UHD-B (matte white) and
CineGrey 5D® (Ceiling Ambient Light Rejecting)
USER’S GUIDE

Pro Series Tripod Tab Tension

Tripod Screen Parts Identification

A. Tripod Screen Setup
Follow the steps below and Fig. 1 & 2.

1. Place the screen in an upright position (Fig.1) with the  legs toward the ground.
2. Deploy the Tripod Support legs by pushing down on the Tripod Junction.
3. Turn the tripod’s screen case in a 90-degree horizontal position so that the screen casing is now parallel to the ground with the screen handle facing the bottom of the  top hook.
4. Completely extend the legs as much as possible so they are stable and position them away from objects that may interfere with their balance. DO NOT stand the tripod  on an unstable platform to avoid an injury should the tripod screen collapse.

B. Preparing the tripod screen for projection:
Follow the steps below and Fig. 3.

1. Pull the screen handle up vertically and hook the screen handle on the Top Hook.Note: Use the Keystone Eliminator to prevent “Keystone Effect” from occurring. Keystone Effect is caused when a projector presents its image at a downward angle causing  a trapezoid-shaped image to appear on the screen. The Keystone Eliminator is designed to eliminate that effect by sloping the screen forward.

2. Push/press the Vertical Locking Tab to unlock the current position of the Vertical Extension Bar and raise it with another hand. Remain pushing on the button until you reach the desired height and let go until you hear a click sound which indicates it is locked in place.

3. Push/press the Screen Height Adjustment Lock/Release located just above the Carrying Handle to raise or lower the bottom of the screen. Once the desired height has been set, let go of the tab to lock the position in place.
   Tripod Skirt Installation

4. Unfold the tripod skirt in a clean area. Use the magnetic bars to attach it to the tripod case. 

C. Collapsing the screen:
Follow the steps below and Fig. 4.

1. Push/press the Screen Height Adjustment Lock/Release Tab to unlock and slowly slide the handle up (NOT all the way) to slowly retract the screen into its case.

2. Press the Vertical Adjustment Lock/Release Tab to unlock and slowly bring the extension bar down to lower the position of the screen’s top hook.

3. Unhook the screen material from the Top Hook and slowly retract the screen back into the case.
   Note: It is very important to remember to hold the extension bar first and then unlock the adjustment tab to prevent the extension bar from slamming and causing injury or damaging the screen.

4. Hold the Extension Bar and Push/press the Vertical Locking tab to unlock and release the position of the extension bar. Bring the extension bar all the way down.

5. Turn the screen’s case vertically clockwise and insert the Top Hook’s bottom pin to lock into the screen’s end cap hole.

6. Close the tripod legs by pushing them in.

Note:

• To ensure the screen is stable, extend the tripod’s legs as much as possible.
• Do not fold the screen or allow any sharp objects to touch the screen’s surface.
• Clean the screen surface often when needed.
• Careful use will extend the lifetime of this product.

For more information, technical support or your local Elite ProAV contact, please visit www.eliteproav.com

Notice to Installer:
Please use the following installation instructions to obtain superior optical performance from the CineGrey 5D® Angular Reflective CLR®/ALR (Ceiling Ambient Light Rejecting) Screen
Make sure to follow these instructions in order for the CineGrey 5D® to perform correctly.

1. Ambient Light must not come from the same direction as the projector’s light
2. Minimum Lens Throw Ratio of 0.8 x image width
3. Compatible with Short Throw projector with a 0.8 lens throw equal or greater
4. Not compatible with Ultra Short Throw Projectors

Note: Improper installation will result in light loss and produce a dark image. This is duc to the projector’s light reflecting in the wrong direction.

References

• Home - EliteProAV - Providing an array of dedicated commercial grade projector screens to professional integrators.
• Homepage - EliteProAV - Providing an array of dedicated commercial grade projector screens to professional integrators.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>