PADORS PSD 109-Halo Luminous LED Light User Guide

PADORS PSD 109-Halo Luminous LED Light

PDS 109-HALO
Luminous LED light Seasonal/Tilt garage door opener
Installation & User Guide www.padors.com

WARNINGS :
Please read this instruction manual carefully before the installation.
This manual is exclusively for qualified installation personnel. PADORS is not responsible for improper
installation and failure to comply with local electrical and building regulations.
Keep all the components of PDS 101-Halo garage opener system and this manual for further consultation.

• In this manual, please pay extra attention to the contents marked by the symbol: A

• Be aware of the hazards that may exist in the procedures of installation and operation of the garage opener system. Besides, the installation must be carried out inconformity with local standards and regulations.

• If the system is correctly installed and used following all the standards and regulations, it will ensure a high degree of safety.

• Make sure that the door works properly before installing the garage opener system and confirm the doors are
  appropriate for the application.

• Do not let children operate or play with the garage opener system.

• Do not cross the path of the garage opener system when operating.

• Please keep all the control devices and any other pulse generator away from children to avoid the system being activated accidentally.

• Do not make any modifications to any components except that it is mentioned in this manual.

• Do not try to manually open or close the doors before you release the opener.

• If there is a failure that cannot be solved and is not mentioned in this manual, please contact qualified installation personnel.

• Do not use the garage opener system before all the procedures and instructions have been carried out and
  thoroughly read.

• Install warning signs (if necessary) on the both sides of the door to warn the people in the area of potential hazards.WARNING:

• Please read this instruction manual carefully before the installation.

• This manual is exclusively for qualified installation personnel. PADORS is not responsible for improper installation and failure to comply with local electrical and building regulations.

• Keep all the components of PDS 101-Halo garage opener system and this manual for further consultation.

• In this manual, please pay extra attention to the contents marked by the symbol:

• Be aware of the hazards that may exist in the procedures of installation and operation of the garage opener system. Besides, the installation must be carried out inconformity with local standards and regulations.

• If the system is correctly installed and used following all the standards and regulations, it will ensure a high degree of safety.

• Make sure that the door works properly before installing the garage opener system and confirm the doors are
  appropriate for the application.

• Do not let children operate or play with the garage opener system.

• Do not cross the path of the garage opener system when operating.

• Please keep all the control devices and any other pulse generator away from children to avoid the system being activated accidentally.

• Do not make any modifications to any components except that it is mentioned in this manual.

• Do not try to manually open or close the doors before you release the opener.

• If there is a failure that cannot be solved and is not mentioned in this manual, please contact qualified installation personnel.

• Do not use the garage opener system before all the procedures and instructions have been carried out and thoroughly read.

• Install warning signs (if necessary) on the both sides of the door to warn the people in the area of potential hazards.

PRODUCT DESCRIPTION

1. APPLICATIONS
   PDS 109-HALO garage door opener is applied for residential automation of garage door. It fits sectional garage door and one piece tilt garage door including “J” and “Track” types. It is operated by main electrical power and it’s not recommended to be operated by back-up batteries for normal use. Back- up batteries are only for emergency operation when there is a power failure, and the carriage can be released by pulling the cord to move the door manually.

2. DESCRIPTION OF THE AUTOMATION

3. The following diagram of typical installation describes some terms and accessories of the door automation system:

Please set stopper in the open limit position of the rack and after the setup is completed, then garage door opener can start the system learning process.
The indication of control panel

Features

• Quiet and powerful 24v DC motor
• Soft start and soft stop
• Automatically selected rolling code to ensure security of unit
• Adjustable opening and closing speed
• Bright LED courtesy light which can be switched on/off independently
• Public main entry mode is available
• Auto counting the cycles of the operation for maintenance

Rail assembly (Only for 3pcs rail ; 1 pcs rail is preassembled)

1. Put the (6) inner trolley assy in the rail track, and put the (5) Metal Rail in the rail track.
2.  Cross the (5) Metal Rail through the (4) front pulley tensioner, the (3) rear pulley support, and the (6) Inner trolley assy. The metal mortise part should be placed in the middle of the whole rail.
3. Connect the (5) Metal Rail.
4. Remove the nut and the spring in the (4) Front pulley bracket. Make sure the metal chain is placed in the gap of the pulley on the two sides. Insert the (2) Front hold bracket against the rail. Use the spring and the nut to adjust the tightness of the (5) Metal chain.

Complete

Attach the rail to the motor

1. Connect the insertion gap of the (3) Rear pulley bracket to the output shaft of the motor.
2. Fasten the rail on the motor with (9) motor hold bracket and motor chassis fixing M6 nut (25).
3. Fasten the (10) Ceiling hold bracket and (13) Ceiling bracket at the rear side between the motor and the rear blocker with motor holder fixing M6 nut (22) and motor chassis fixing M6 nut (25). Remark: Optional choice is to use L-bracket to hold the brackets to the ceiling, and fasten to both the ceiling and ceiling bracket(13) using Hex bolt(20) and motor chassis fixing M6 nut (25).

Attach the rail on the header wall and ceiling

1. Position (11) Header bracket on the header wall.
   It is recommended that positioned at the center of the garage door.
   The installation height of the {11) Header bracket varies from 30-50cm from the top of the garage door.

2. Install the (11) Header bracket with screws.

3. Attach the front rail to header bracket with bolts.

4.  Attach the (13) Ceiling bracket on the crossbeam of ceiling with crews.

Attach Rail to the Header Bracket

CAUTION
To prevent damage, place the garage door on the top section to create a temporary support.

Connect release section to the garage door

1. Connect the (7) Release rope on the (8) Release trolley
   • WARNING
   • To prevent possible SERIOUS INJURY or DEATH from a falling garage door:
   • If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.
   • NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.
   • NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall.
   • NOTE: Handle should hang 6 feet (1.5 m) above floor. Ensure that the rope and handle clear the tops of all vehicles to avoid entanglement.
   • CONNECT DOOR ARM TO TROLLEY
2. Pull the (7) Release rope to disengage the (8) Release trolley
3. Connect (15) Straight door arm to Release trolley
4. Fasten the (12) Door bracket and (16) Door bracket locater on the center of the garage door. Connect (14) Bent arm to (12) Door bracket.
5. Connect (14) Bent arm and a straight arm with bolts and nuts.

Final steps before system learning

1. Install the blocker (16) on the door opened position ( behind the up limit)
2. Attached the warning sign to the (7) release rope.
3. connect the power to the motor. Make sure the electric plug and socket are well connected.

WARNING
To prevent possible SERIOUS INJURY or DEATH from electrocution or fire:

• Be sure power is not connected to the opener, and disconnect power to circuit BEFORE removing cover tc establish permanent wiring connection.
• Garage door Installation and wiring MUST be in compliance with all local electrical and building codes
•  NEVER use an extension cord, 2-wire adapter, or change plug in ANY way to make it fit outlet. Be sure the opener is grounded.

Introduction of the emergency release

1. Pull the (7) Emergency release rope to release the trolley. Make sure the trolley is disengaged. The garage door can be operated manually.
2. Before restarting the motor, manually move the garage door until the trolley is engaged.

Connection

1. Accessories connection
   Only carry out electrical connections once the electricity supply to the system has been switched off.

2. Door position for start-up phase

   • Position carriage at approximately half travel before starting check and start-up phase of the automation.

   • This will ensure the leaf is free to move both during opening and closing.

   • Power supply connection

   • Connect the plug. As soon as the system is powered, you should check the LED in the display. Make sure the LED display is ON.

   • Never cut or remove the cable supplied with PG Series garage opener. If not already available, the power socket of PG Series
     garage opener connection must be fitted by skilled and qualified personnel in strict observance of current legislation, standards and regulations.

   • The power supply line must be protected from short circuits and ground leakage.

3. Coding transmitter and erasing process

   • A. Coding transmitter:

   • Pressing “C” button once, a dot LED is on. Then press same desired button on the transmitter twice. The dot LED Is off – flashing – off. The programming is completed.

   • Erasing Transmitter Memory:

   • Press and hold “C” button till “L” showing on the display screen. Then release the button. The dot LED is flashing and then turn
     to “L” flashing while pressing the ”C” button.

   •  System learning, reset process, and LED display

   • A. Program Door Travel Limits

   • Setting your door travel limits is a vital part of the initial setup of your opener. the specific distance must travel to complete the open/close cycle.

   • Stepl: Press and hold “P” buttons for 8 seconds, the LED display shows “1 “. The opener enters system setting mode.

   • Step2: Press “P” button, LED display shows” n “. Press and hold     button to open the door. When the door moves to the desired opening position, press “P” button to save.

   • Step3: LED display shows “u “. Press and hold   button to close the door. When the door moves to the desired closing position, press “P” button to save.

   • Step4: Once limits are set, the opener will automatically open and close by itself for detecting the opening and closing force of the sensitivity. When the door is closed after calibration, limits set up is completed.

   • Step5: Program Force Settings

   • To ensure your doors Force Settings are correct, place a 40mm solid immovable object (eg block of wood} in the middle of the opening and lower the door. The door should automatically reverse when it touches the wood without further
     adjustments. If the door doesn’t auto-reverse, complete the following steps to adjust settings:

   • Decrease the closing force to level 2 -4 from 5 to increase the sensitivity of auto-reverse function.

   • Press and hold “P” till “1” on the display. Press “UP” to “2”, then press “P”. Using “UP” and “DOWN” to adjust closing force. Default is level “5”.

How to set the parameter:

• Step 1: Press the “P” button for 8 seconds, the display will show /. The opener is on setting mode.
• Step 2: Choosing a desired function by .A. and ‘Y , then press the “P”. A second number shows on the display. Choosing desired number to set on/off or level, then press “P” to save. Please refer to below table for the details of the functions
• The functions of “Ventilation”, “Coding by remote” and “Lighting” on the below table, only work with when the first button on the remote is coded.

Programming the opener

Initial Powering Up of Opener
Once your Opener has been installed, push and pull the door by hand to ensure the manual release thrust block is locked into place before turning on the power.

Wiring diagram for push button and safety beam

Specification

• 24V DC

• -20 °c, < +50°C

|

• Decoding
• Transmitter Power

|

• Rolling Code
•  2 x 3V Lithium Cell 2016

Relative Humidity| 90%| Globe| LED
Open/Close Force| 800N  1000N 1200N| Courtesy Light Time| 3 minute

Tools required

Notice

• Final notes
• This manual is only used by technical persons who are qualified to carry out the installation.
• No given information in this manual can be considered of any interest to the end user.
• It is important for the installer to show their clients correct operation using of the opener including the using of manual disengagement cord.
• Inform the owner about the need of a regular and accurate maintenance, especially regarding a regular check of the safety and reversing devices.
• Important information for the user
• Once the opener has been installed, the user must be informed about how it works and all the risks that can arise if it is used improperly. The user must avoid placing himself/herself in dangerous situations such as standing within the door’s operating range when it is moving.
• Do not let children play near the door, and keep the remote controls out of their reach.
• All services, repairs or checks must be carried out by professionally qualified persons, and noted on a maintenance register kept by the user.
• IMPORTANT NOTE : In the case of a malfunction the user must call an authorized installer and should not attempt to repair it without professional help or experience.

Warranty

• Padors offers a two year standard Back to Base warranty on the motor only for all DIY consumers. It is handled under a Replace/ Return Warranty. If the opener has an issue we cannot solve over the phone, you send back the faulty unit to us at your cost. We will send the fixed unit to you within 24 hours once we receive the unit at our cost.
• If the opener is installed by our accredited installer, the warranty period will be offered from two to ten years from the installer based on the door’s condition and special service terms. The installer will take the warranty. We, PADORS, offer the warranty to our accredited installer. We will not deal with the consumer directly.
• Notice : It is not waterproof products. It will not be covered by the warranty if installing at outside and inflow of water.

GARAGE DOOR OPENERS USER MANUAL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>