Mag One MDPMLN4445, MDPMLN4558 Ultra Light Headset with Swivel Boom Microphone User Guide
- July 3, 2024
- Mag One
Table of Contents
Mag One MDPMLN4445, MDPMLN4558 Ultra Light Headset with Swivel Boom
Microphone
Product Information
Specifications
- Model: MAG ONE ULTRA-LIGHT HEADSET
- Microphone: Swivel Boom Microphone
- Switch: In-line PTT/VOX Switch
- Model Numbers: MDPMLN4445, MDPMLN4558
Product Usage Instructions
- Switch the radio on and wait for the green LED light to extinguish, ensuring the volume is not too loud.
- Hold the microphone close (about 3 cm) to your mouth for voice transmission.
- Press the accessory PTT to speak into the microphone for two-way communication; the red LED indicates communication.
- Adjust speaker audio level using radio volume control.
- Switch off the radio before disconnecting the accessory.
- Ensure the radio is programmed for VOX operation.
- Switch off the radio before connecting the audio accessory.
- Plug the connector into the accessory jack and set the PTT selector switch to VOX.
- Switch on the radio and wait for the green LED light to extinguish, ensuring the volume is not too loud.
- Hold the microphone close to your mouth for voice transmission.
- Speak into the microphone for two-way communication; a red LED indicates communication.
- Adjust speaker audio level using radio volume control.
- Switch off the radio before disconnecting the accessory.
- Keep the audio accessory dry and store at normal room temperature.
- Avoid pulling the wire cord to remove the accessory from the radio.
- Avoid excessive winding of the wire cord.
- Clean with a damp cloth.
FAQ
- Q: How do I know if the two-way communication is working?
- A: The red radio light (LED) illuminates to indicate that two-way communication is working when you speak into the microphone.
DESCRIPTION
- The MAG ONE accessory line gives you the maximum value for your investment.
- Best suited for indoor use, the MAG ONE accessory line provides portable, convenient communication to receive or transmit messages without removing your radio from your belt or carry case.
- Enjoy the added benefit of total handsfree communication when this accessory is used with a Voice Operated eXchange (VOX)-enabled radio.
PUSH-TO-TALK (PTT) OPERATION
-
Switch off your radio before connecting the audio accessory.
-
Plug the connector into the accessory jack.
-
Set the Push-To-Talk (PTT) selector switch to PTT. See Figure 1.
-
Switch the radio on and wait for the green radio light (LED) to extinguish. Ensure that the volume level is not too loud.
Note: When the audio accessory has been installed, the radio microphone and the radio speaker will be disabled. Use the audio accessory to transmit and listen to incoming calls. -
Hold the microphone close to your mouth (about 3 cm) for maximum voice transmission.
-
Press the audio accessory PTT and speak into the microphone to check that the two-way communication is working. The red radio light (LED) illuminates to indicate the two-way communication is working. Release the accessory PTT to listen to incoming calls.
-
Adjust the accessory speaker audio level using the radio volume control.
-
Always switch your radio off before disconnecting the accessory.
VOX OR HANDS-FREE OPERATION
Ensure that the radio has already been programmed to enable Voice Operated
eXchange (VOX) operation using the dealer radio programming software.
-
Switch your radio off before connecting the audio accessory.
-
Plug the connector into the accessory jack.
-
Set the PTT selector switch to VOX. See Figure 1.
-
Switch the radio on. Wait for the green radio light (LED) to extinguish. Ensure that the volume level is not too loud.
Note: When the audio accessory has been installed, the radio microphone and the radio speaker will be disabled. Use the audio accessory to transmit and listen to incoming calls. -
Hold the microphone close to your mouth (about 3 cm) for maximum voice transmission.
-
Speak into the microphone to check that the two-way communication is working. The red radio light (LED) illuminates to indicate the two-way communication is working.
-
Adjust the accessory speaker audio level using the radio volume control.
-
Always switch the radio off before disconnecting the accessory.
Note: Pressing the radio PTT button will temporarily disable the VOX operation. Communication can continue using the audio accessory microphone and the radio PTT button. To reselect the audio accessory VOX operation, turn the radio OFF and repeat the setup procedure steps (4) to (7).
CARE AND MAINTENANCE
- Keep the audio accessory dry. Use and store at normal ambient room temperature only.
- Do not pull the wire cord to remove the audio accessory from the radio. Pulling of the cord may damage the internal cables and cause permanent failure.
- Avoid excessive winding of the wire cord at all times.
- Clean with a damp cloth.
© 2024 Motorola Solutions, Inc. All rights reserved.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS, and the Stylized M logo are trademarks or
registered trademarks of Motorola Trademark Holdings, LLC and are used under
license. All other trademarks are the property of their respective owners.
