TOPWAY em 21YX48BK Rugged Speaker User Guide
- June 3, 2024
- TOPWAY em
Table of Contents
TOPWAY em 21YX48BK Rugged Speaker
What’s in box
Specification
- Bluetooth version: V5.1
- Product size: 93.5mm(H) X 75.5mm(W)
- Pairing name: WIRELESS SPEAKER
- Speaker diameter: 52mm
- Microphone_Sensitivity: -42 ± 3dB at 1mw 1kHz
- Operating range: 10m
- Battery capacity of earbuds: 1200mAh
- Working hour: upper than 10 hours
- Charging time: about 3 hrs
- Bluetooth profile: HFP A2DP HSP AVRCP
- Warning: Risk of fire, burns and explosion, Do not open, crush, heat above 45°C or incinerate.
Produced for Walmart inc.
Bentovile. AR72716
1-888-516-2630
Website: https://www.walmart.com/
Power on/off
- Power on: press and hold for 2s until you hear the ‘power on’ prompt voice.
- Power off: press and hold for 2s until you hear the ‘power off’ prompt voice and LED light off. In paring mode but not connected beyond 5 mins, the Rugged speaker will power off automatically.
Bluetooth paring
First press and hold for 2s until you hear the ‘power on’ prompt voice, the Blue LED will come on and blink. This means Rugged speaker is in pairing mode, make sure Bluetooth is enabled on your audio source and in a few moments, pairing name ‘WIRELESS SPEAKER’ will appear on your list, then press it to connect, the LED will flash blue every 5 seconds which means you are paired.
(Conveniently, From now on, when you turn on Rugged speaker it will automatically search for the last Bluetooth device it was paired with and reconnected)
WIRELESS STEREO PAIRING
Let the two speakers into pairing mode, short press one speaker’s MFB
button, wait a moment, they will paired together, there is ‘tone’ voice remind
.
Play music
- Press and hold to adjust previous/ next song
- Play/pause music: single click
- Volume+ &-: Single click
Phone call
- Answer &hang up
- Reject a call
- Volume+ &-: Single click
Charging
Rugged speaker comes with a lithium-ion battery. For best result, fully charge
Rugged speaker before use. (recommended output of charging device is 1A) To
charge, plug the TYPE C charging cable into Rugged speaker and plug the
standard USB connector into your power source ( If power source is Laptop,
Desktop, much more charging time (5-6 hours) will be needed) While charging
the LED solid Red, fully charged, light off.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference in a residential installation, this equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. May cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Changes or modifications not expressly approved by the
party responsible for compliance could vold the user’s authority to operate
the equipment.
Warning: Changes or modifications to this unit not espressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Trouble Shooting and Common Situations
Rugged Speaker cannot power on
Battery drain, please charge the device for 30 minutes, and then powering on.
Smart phone cannot search Bluetooth Rugged Speaker
- Make sure the Rugged Speaker is in pairing mode ( Blue light blink)
- Delete pairing list in smartphone and searching WIRELESS SPEAKER again.
- If it still cannot be found, please restart smartphone and Rugged Speaker again.
Rugged Speaker will be disconnected from time to time
- The battery drain.
- The Rugged Speaker is beyond the communication range(10m).
No sound on talking mode
- Confirmed the Rugged Speaker connected to earpiece mode on talking.
- Try to volume up Rugged Speaker or smartphone.
No sound with music playing
- Try to volume up Speaker or smart phone.
- Rugged Speaker disconnected with smartphone, please reconnected again.
Cannot charger for Rugged Speaker
- The charger cable connected not well.
- Charger line was damaged.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>