Variscite DART-MX95 Based on NXP i.MX95 Evaluation Kit User Guide

June 30, 2024
Variscite

DART-MX95 Based on NXP i.MX95 Evaluation Kit

“`html

Specifications

  • Product: DART-MX95 based on NXP i.MX95 Evaluation Kit
  • Processor: NXP i.MX95
  • Display: 7″ LCD
  • Storage: eMMC and microSD card support
  • Connectivity: USB, Touchscreen
  • Power: 5V

Product Usage Instructions

Evaluation Kit Initial Setup

  1. Carefully remove the 7″ LCD and VAR-DT8MCustomBoard from the
    package.

  2. Connect the 7″ LCD Display and Touch cables to the Evaluation
    Kit connectors J15, J18 respectively. Note: connect the display
    cable with the red wire on pin 1. Connect the touch cable with the
    metal contacts facing down.

  3. Plug the USB type A to micro B cable between the USB debug
    connector (J10) and a PC USB port.

  4. For heatsink assembly instructions, please refer to the
    VHP-DT8MM/P documentation. Note: The heatsink is mainly used for
    CPU/GPU intensive applications and may be required per your
    specific use case.

Setting the Host PC for Debug

  1. Download any PC terminal software (e.g. Putty).
  2. Set the PC terminal software parameters as follows:
    • Baud Rate: 115200
    • Data bits: 8
    • Stop bits: 1
    • Parity: None
    • Flow Control: None

Booting from eMMC

  1. For internal boot: Set the Boot select switch (SW7) to INT
    position to boot from the SOM’s internal storage.

  2. Plug the wall adapter into the 5V power jack (J4) and to a
    120VAC~240VAC power source.

  3. Set Power ON switch (SW8) to ON state.

  4. Boot messages should be printed within the PC terminal
    window.

Booting from a Micro SD Card

  1. Set Power ON (SW4) to off state.

  2. Set Boot select switch (SW7) to EXT side in order to boot from
    the SD card.

  3. Push microSD card into the microSD card slot (J9) of the
    VAR-DT8MCustomBoard.

  4. Set Power ON switch (SW8) to ON state.

  5. Boot messages should be printed within the PC terminal
    window.

FAQ

Where can I find more information about Variscite’s DART-MX95

products?

You can visit Variscite’s website at the following links:

If you need further assistance, you can contact Variscite at
sales@variscite.com.

P/N VSS0200

“`

DART-MX95 based on NXP i.MX95 Evaluation Kit Quick Start Guide

12

13

14

16

18

19

20

15

17

11

21

10

22

23 24
25 9
26
27

28

8

7

6

5

Features
1. 5V PWR IN (J4) 2. Gigabit Ethernet #1 (J5) 3. USB 3.0 OTG (J6) 4. Gigabit Ethernet #2 (J43) 5. Dual USB 2.0 Host (J7) 6. FAN 5V (J24) 7. micro SD Card slot (J9) 8. USB Debug (J10) 9. RTC BAT. Slot (JBT1) 10. Single MIPI-CSI (J11) 11. Mini PCIe #1 (J23) 12. UART, I2C (J12) 13. SAI1, PDM, CAN (J13) 14. UART, SPDIF,GPIO (J14) 15. QSPI (J41) 16. LVDS CH0 (J15) 17. LVDS CH1 (J26) 18. ECSPI, Host wake ,CAN(J16) 19. Resistive Touch (J17) 20. Capacitive Touch (J18) 21. User Buttons (SW1-SW4) 22. GPIO (J25) 23. Reset Button (SW5) 24. ON/OFF Button (SW6) 25. Line In (J21) 26. Boot Select Switch (SW7) 27. Headphones (J22) 28. Power ON (SW8)

4

3

2

1

Evaluation kit initial Setup
1. Carefully remove the 7″ LCD and VAR-DT8MCustomBoard from the package.
2. Connect the 7″ LCD Display and Touch cables to the Evaluation Kit connectors J15, J18 respectively. Note:connect the display cable with the red wire on pin 1. Connect the touch cable with the metal contacts facing down.

3. Plug the USB type A to micro B cable between the USB debug connector (J10) and a PC USB port.
4. For heatsink assembly instructions, please follow the VHP-DT8MM/P documentation. Please note that the heatsink is mainly used for CPU/GPU intensive applications and may be required per your specific use case.

DART-MX95 based on NXP i.MX95 Evaluation Kit Quick Start Guide

Setting the host PC for debug
1. Download any PC terminal software (e.g. Putty).
2. Set the PC terminal software parameters as follows: – Baud Rate: 115200 – Data bits: 8 – Stop bits: 1 – Parity: None – Flow Control: None
Booting from eMMC
1. For internal boot: Set the Boot select switch (SW7) to INT position to boot from the SOM’s internal storage.
2. Plug the wall adapter into the 5V power jack (J4) and to a 120VAC~240VAC power source.
3. Set Power ON switch (SW8) to ON state. 4. Boot messages should be printed within the
PC terminal window.
Booting from a micro SD card
The microSD card is supplied within the package. Updated SD card images can also be downloaded from the Variscite FTP server. See more details in the recovery SD card section in the Variscite wiki pages.

(Re-)Installing the file system on the eMMC
Please refer to the recovery SD card section in the Variscite wiki pages.
Links
o Wiki page: https://variwiki.com/index.php?title=DARTMX95
o DART-MX95 Evaluation kits: https://www.variscite.com/product/evaluationkits /dart-mx95-evaluation-kits/
o DART-MX95 System on Module: https://www.variscite.com/product/system- onmodule-som/cortex-a55/dart-mx95-nxp-i-mx95/
o VAR-DT8CustomBoard carrier board: https://www.variscite.com/product/single- boardcomputers/var-dt8mcustomboard
o Customer portal: https://varisciteportal.axosoft.com/login

1. Set Power ON (SW4) to off state. 2. Set Boot select switch (SW7) to EXT side in
order to boot from the SD card. 3. Push microSD card into the microSD card
slot (J9) of the VAR-DT8MCustomBoard. 4. Set Power ON switch (SW8) to ON state. 5. Boot messages should be printed within the
PC terminal window.

Thank you for purchasing Variscite’s product.
For additional assistance please contact: sales@variscite.com

P/N VSS0200

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals