KENYON 145739 Signature Grill With Intelliken Touch Owner’s Manual
- June 28, 2024
- KENYON
Table of Contents
www.CookWithKenyon.com
Make any day a weekend SIGNATURE GRILL
WITH INTELLIKEN TOUCH™
OWNERS MANUAL
Part #145739
Created: June 12, 2024
145739 Signature Grill With Intelliken Touch
Please read & save these instructions
Thank you for choosing Kenyon, the world’s leading manufacturer of specialty
cooking appliances.
By following the instructions in this owners manual, your grill will provide
you with many years of reliable service.
To ensure our ability to continue serving you, please use this page to record
important product information.
For quick reference please keep a record here:
Purchase date
Model number
Serial number
Name plate location![KENYON 145739 Signature Grill With Intelliken Touch
- assembly](https://manuals.plus/wp-content/uploads/2024/06/KENYON-145739 -Signature-Grill-With-Intelliken-Touch-assembly.jpg)
IMPORTANT SAFETY INSTRUCTIONS
Read this section BEFORE operating the grill.
The following information applies to all KENYON Grills.
THIS GRILL, LIKE ALL APPLIANCES, HAS THE POTENTIAL TO CREATE SAFETY PROBLEMS
THROUGH CARELESS AND IMPROPER USE. PLEASE OBSERVE ALL OF THE FOLLOWING SAFETY
PRECAUTIONS.
Read ALL instructions prior to using product.
CAUTION
Do not touch hot surfaces. Use handles or knobs.
To protect against electrical shock, do not immerse cord or plugs in water or
other liquid.
Allow to cool before putting on or taking off parts.
Warning: If the surface is cracked, switch off the appliance to avoid the
possibility of electric shock, for hob surfaces of glass-ceramic or similar
material which protect live parts.
Do not operate appliance with a damaged power cord or plug. If the appliance
malfunctions, discontinue use. Contact KENYON Customer Care immediately at
860-664-4906.
The use of accessory attachments not supplied by the manufacturer of the
appliance may cause injuries.
Do not let cord hang over edge of table or counter, or touch hot surfaces.
Always place a minimum of two (2) cups of water in each drip tray prior to
grilling.
Never leave children alone – children should not be left unattended around the
grill at any time.
Close supervision is necessary when any appliances are used near children.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Cleaning and user maintenance shall not be made by children without
supervision.
Allow the grill to cool before taking off cooking grates, drip trays or lid.
Fuel, such as charcoal briquettes, are not to be used with this appliance.
Do not place on or near a hot gas or electric burner, or in a heated oven.
Extreme caution must be used when moving an appliance containing hot oil or
other hot liquids.
Ensure grill is installed per instructions and properly grounded by a
qualified electrician.
Do not use water to extinguish a grease fire, use dry chemical fire
extinguisher.
Do not use appliance for other than intended use.
Do not replace or attempt to repair any part of the grill, unless otherwise
noted in this manual. All other service is to be performed by a factory
authorized technician.
Do not store flammable materials near the grill.
Do not wear loose fitting or hanging apparel when using the grill.
DO NOT DISCARD THESE INSTRUCTIONS, KEEP THEM WITH THE KENYON GRILL FOR FUTURE
REFERENCE.
WARNING!
Charcoal or similar combustible fuels must not be used with this
appliance.https://qrco.de/beTFuU
Point your phone’s camera at the QR Code to view our Quick Start Tips video
for the Electric Grill.
Product Specifications
Overall & Cutout Dimensions PRODUCT DIMENSIONS
WIDTH | DEPTH | HEIGHT |
---|---|---|
29 1/2” | 21” | 16 3/4” (lid open) |
749mm | 533mm | 425mm (lid open) |
CUTOUT DIMENSIONS
WIDTH | DEPTH | RADIUS |
---|---|---|
28” | 18 1/2” | 1/4” |
711mm | 470mm | 6mm |
ELECTRICAL SUPPLY REQUIREMENTS
The supply must be from an individual grounded circuit that is protected by a
circuit breaker and rated per the specifications for the model as shown in
this table.
KENYON PART NUMBER| MAX CONNECTED LOAD| POWER
SUPPLY INPUT| PLUG TYPE| LID COLOR| HANDLE
TYPE
---|---|---|---|---|---
B70428| 3000 Watts| 240V| NEMA 6-15| STAINLESS STEEL| STATIONARY
B70428UK| 3000 Watts| 240V| UK| STAINLESS STEEL| STATIONARY
B70428SCHUKO| 3000 Watts| 240V| SCHUKO| STAINLESS STEEL| STATIONARY
B70428NH| 3000 Watts| 240V| NEMA 6-15| STAINLESS STEEL| STATIONARY
B70429| 3000 Watts| 240V| NEMA 6-15| STAINLESS STEEL| LIGHTED
B70429UK| 3000 Watts| 240V| UK| STAINLESS STEEL| LIGHTED
B70429SCHUKO| 3000 Watts| 240V| SCHUKO| STAINLESS STEEL| LIGHTED
B70429NH| 3000 Watts| 240V| NEMA 6-15| STAINLESS STEEL| LIGHTED
B70473| 3000 Watts| 208V| PIGTAIL| STAINLESS STEEL| STATIONARY
B70473NH| 3000 Watts| 208V| PIGTAIL| STAINLESS STEEL| STATIONARY
B70474| 3000 Watts| 208V| PIGTAIL| STAINLESS STEEL| LIGHTED
B70474NH| 3000 Watts| 208V| PIGTAIL| STAINLESS STEEL| LIGHTED
B70428CF| 3000 Watts| 240V| NEMA 6-15| BLACK CARBON FIBER| STATIONARY
B70428NHCF| 3000 Watts| 240V| NEMA 6-15| BLACK CARBON FIBER| STATIONARY
B70429CF| 3000 Watts| 240V| NEMA 6-15| BLACK CARBON FIBER| LIGHTED
B70429CFUK| 3000 Watts| 240V| UK| BLACK CARBON FIBER| LIGHTED
B70429CFSCHUKO| 3000 Watts| 240V| SCHUKO| BLACK CARBON FIBER| LIGHTED
B70429NHCF| 3000 Watts| 240V| NEMA 6-15| BLACK CARBON FIBER| LIGHTED
B70429NHCFUK| 3000 Watts| 240V| UK| BLACK CARBON FIBER| LIGHTED
B70429NHCFSCHUKO| 3000 Watts| 240V| SCHUKO| BLACK CARBON FIBER| LIGHTED
B70474CF| 3000 Watts| 208V| PIGTAIL| BLACK CARBON FIBER| LIGHTED
B70474NHCF| 3000 Watts| 208V| PIGTAIL| BLACK CARBON FIBER| LIGHTED
IMPORTANT!
If the electrical supply does not meet the product specifications, consult
with a licensed electrician before proceeding with installation!
ELECTRICAL SUPPLY REQUIREMENTS
The supply must be from an individual grounded circuit that is protected by a
circuit breaker and rated per the specifications for the model as shown in
this table.
__KENYON PART NUMBER| MAX CONNECTED LOAD| POWER
SUPPLY INPUT| PLUG TYPE| LID COLOR| HANDLE
TYPE
---|---|---|---|---|---
B70428WCF| 3000 Watts| 240V| NEMA 6-15| WHITE CARBON FIBER| STATIONARY
B70428NHWCF| 3000 Watts| 240V| NEMA 6-15| WHITE CARBON FIBER| STATIONARY
B70429WCF| 3000 Watts| 240V| NEMA 6-15| WHITE CARBON FIBER| LIGHTED
B70429WCFUK| 3000 Watts| 240V| UK| WHITE CARBON FIBER| LIGHTED
B70429WCFSCHUKO| 3000 Watts| 240V| SCHUKO| WHITE CARBON FIBER| LIGHTED
B70429NHWCF| 3000 Watts| 240V| NEMA 6-15| WHITE CARBON FIBER| LIGHTED
B70429NHWCFUK| 3000 Watts| 240V| UK| WHITE CARBON FIBER| LIGHTED
B70429NHWCFSCHUKO| 3000 Watts| 240V| SCHUKO| WHITE CARBON FIBER| LIGHTED
B70474WCF| 3000 Watts| 208V| PIGTAIL| WHITE CARBON FIBER| LIGHTED
B70474NHWCF| 3000 Watts| 208V| PIGTAIL| WHITE CARBON FIBER| LIGHTED
IMPORTANT!
If the electrical supply does not meet the product specifications, consult
with a licensed electrician before proceeding with installation!
Before Using the Grill
-
Remove the cooking grates and drip trays from the grill. Wash the grill with warm soapy water using a non-abrasive cloth.
USE ONLY HIGH TEMP PLASTIC UTENSILS WHEN GRILLING. Visit our web site to purchase a set of high quality stainless steel/high temp plastic grill utensils, www.cookwithkenyon.com. -
Make sure the drip trays are inserted all the way into the bottom of grill and electric element brackets are resting on the element support bracket.
-
Cover the bottom of the drip trays with a liquid. Water is fine. PLEASE DO NOT USE A FLAMMABLE LIQUID! Doing so would ruin your cookout. Using apple juice if you are grilling pork adds a nice flavor to the meat. A can of lime soda is wonderful if you are grilling fish. Just remember always add liquid to the drip trays prior to grilling.
-
To keep your grill smoke free, always clean the grilling surfaces after each use. Simply wash with warm soapy water using a non-abrasive cloth or place in your dishwasher. Empty the drip trays and wipe with a damp paper towel.
-
Place your cooking grates or optional griddles (part #B96000) onto the element with drip trays installed. Use the griddles for foods such as eggs, pancakes or my favorite – stuffed french toast!
-
Preheat grill with the lid closed for 5 – 7 minutes on desired heat setting for type of food:
• Steak – Temp setting 550˚F/ Power setting 16
• Burgers – Temp setting 500˚F/ Power setting 9
• Pork and Fish – Temp setting 400˚F/ Power setting 5
• Vegetables – Temp setting 350˚F/ Power setting 4 -
Close the lid and cook. Enjoy the best grilled food you have ever tasted!
-
Clean up. After the grill has cooled to the touch, take a few pieces of paper towel and place on the grilling surface. Pour about one ounce of water on the towel and then using your high temperature nylon tongs, swab the paper toweling back and forth to loosen up the residue from your grilling. Throw the paper towel away and wipe the grates off with a dry paper towel.
-
Once the grates have cooled sufficiently, remove the grates and place in your dishwasher for a thorough cleaning.
-
With the grates removed, lift up the electric elements and remove the drip trays. Empty the contents of the drip trays in an appropriate place. Wipe the trays out with a dry paper towel and reuse the trays.
-
After using your grill many times, you may want to wash the lid. It can be placed in your dishwasher and run on the pots & pans cycle. If your grill is equipped with a rotating handle with an LED light, be sure to remove the flashlight from the handle before placing the lid in the dishwasher (see page 18 for removal instructions). This will restore your grill to its original pristine look.
-
To clean the grill, first be sure the cooking surface has cooled enough to handle. Then remove the grates, lift up the electric elements until they lock in the up position, remove the middle grate support cross bar, then the drip trays. The grate support cross bar is removed by lifting the rear and pulling the front notch off of the supporting tab. To install the support reverse the procedure. Do not cook on the grill without the support cross bar in place!
-
Wipe the stainless steel surfaces with a damp cloth to remove any residue from previous grilling sessions.
-
Your Kenyon grill came with a sample bottle of stainless steel cleaner. Use this cleaner once a month to keep your grill looking like new.
-
The touch control area is ceramic glass which is sealed from the effects of rain, snow and ice. To clean the glass, use a glass cleaner and soft towel. If stains appear, use a ceramic glass cleaner which can be found in your local grocery store.
Operation
DO NOT USE WATER ON GREASE FIRES
Smother fire or flame or use dry chemical or foam-type extinguisher.
USE ONLY DRY POT HOLDERS
Moist or damp pot holders on hot surfaces may result in burns from steam. Do
not let pot holder touch the grate or element of the grill. Do not use a towel
or other bulky cloth in place of a pot holder.
DO NOT COOK ON BROKEN GRILL GRATE OR GRIDDLE
If the grate should break, grease and oils may come into direct contact with
the electric element and create a risk of electric shock or fire. Contact an
authorized service center or KENYON Customer Care immediately at
860-664-4906.
CLEAN GRILL WITH CAUTION
If a wet sponge or cloth is used to wipe spills on a hot cooking surface, be
careful to avoid steam burns. Some cleaners produce noxiousfumes if applied
to a hot surface. Read the cleaner label for details prior to using.
DO NOT TOUCH HEATING ELEMENT OR GRATE
The heating element and grate will be hot for some time after cooking. These
components should be allowed to cool and then be handled with care and caution
while cleaning, as they may be hot enough to cause severe burns.
Do not operate appliance with a damaged power cord or plug. If the appliance
stops working properly, stop using it and contact the nearest authorized
appliance dealer or the factory to get it checked or fixed.
CLEAN GRILL AFTER EACH USE
This appliance is equipped with removable, drip trays. The drip trays MUST be
removed and cleaned after each and EVERY use.
Do not allow grease to accumulate between cooking. The drip trays and baffle
tray MUST be used when cooking on the grill. Excessive grease may spill over
into the interior of the grill, voiding your warranty and posing a fire
hazard.
NEVER LEAVE GRILL UNATTENDED AT HIGH HEAT SETTINGS
High heat setting may cause heavy smoking and ignite grease.
DO NOT CLEAN UNIT WITH PRESSURIZED WATER
Never clean the grill with any form of pressurized water or other types of
cleaners.
Doing so will void the warranty and may pose a serious risk of electric shock.
Always clean the grill with a cloth and a stainless steel or glass surface
cleaner.
STORAGE
Suitable shelter must be provided to prevent direct exposure to rain. Covers
available at www.cookwithkenyon.com.
TO PREVENT SMOKE
To prevent the contents of the drip trays from smoking, place 2 cups of water
(or enough to cover the bottom of the pan) in each of the drip trays before
cooking.
DO NOT USE POTS OR OTHER BAKEWARE ON THE GRILL
KEEP THESE INSTRUCTIONS WITH THE GRILL FOR FUTURE REFERENCE
Indicator Lights
There are a series of lights that provide indications of element operation and
hot surfaces.
These lights are located adjacent to the control panels. When the control is
ON, a LED light array will illuminate indicating which element is on.
For your safety, we have incorporated a “HOT” indicator light. When lit, this
light indicates that some part of the cooking grate is too warm to touch or
place articles upon. Do not place articles on the cooking surface while this
light is glowing.
After turning off the element, the “HOT” indicator light will remain
illuminated until the cooking grate is safe to touch.
Turning On
Touch the controls firmly with the flat part of your fingertips.
With the unit unlocked, touch the POWER button in the main control frame.
Activate either element by holding the element power button in the control
frame for 2 seconds and choosing a cooking option. If an element is not
activated within 15 seconds, the grill will de-power by itself.
Safety Lock Feature
When the LOCKED LED is illuminated in the main power control frame, the grill
touch control power settings can’t be adjusted from the current setting.
Pressing either the zone power button or the master power button however, can
turn off the grill. The LED arc light array will no longer illuminate when in
the lock mode. The lock feature can be activated at any time as a safety
measure, whether the unit power is on or off. When the unit has power the
STANDBY light will illuminate. To unlock the grill, swipe the LOCK feature with your fingertip
along the gradient surface, from the LOCK to the UNLOCK position as indicated
by the key and open padlock graphics or touch and hold the UNLOCK graphic for
3 seconds.
To LOCK the grill, swipe from the UNLOCK to the LOCK position or touch and
hold the LOCK button for 3 seconds.
Cooking Mode Options
The grill elements can be independently operated by either a heating level
ranging from low to high, or by setting a specific cooking temperature.
Temperature Cooking Mode
With the main power on and the element powered on, select the desired cooking
temperature, ranging from 150° to 550°F (65° to 287°C), in 10°F (5.5°C)
increments. The selection can be made by pressing + or – buttons for each
increment change, or swiping the arc.
The selected cooking temperature value will illuminate and flash in the
control frame while the selection is in progress. The value will flash until
the temperature is reached. After the temperature has been reached the value
will illuminate steady, and the cooking
temperature will remain set unless it is changed.
The default temperature setting is always 150°F (65°C) upon startup in
temperature cooking mode.
Changing Temperature Units
The temperature units can be changed from Fahrenheit to Celsius by touching
the °F/°C button in the main power control frame. All active elements will
change accordingly. The chosen default units will remain with every use unless
changed. Heat Level Cooking Mode Select the heat level cooking mode by
touching the thermometer/gradient graphic within the chosen element control
frame. The settings range from LOW-MED-HIGH in 16 increments, as indicated by
the LED light array that illuminates along the control sweep. Also, the arc+
and – signs can be toggled to select the desired heat level. The LED light
array will indicate the selected setting. Timer Options
Kitchen Timer
The kitchen timer is a general timer that has many uses around the kitchen,
independent of cooking activity on the grill.
Activate the main power and touch the timer clock graphic within either
element control frame. Set the desired time duration by touching the + and –
buttons, holding the button to increase or decrease the setting. A beep will
sound at the start of the setting and the set time will display in the control
fame. The time increments will run from 1-10 minutes in 1 minute increments,
and then change to 5 minute increments. The time reading will speed up as the
touch is held. Touch the timer button again to start. If no time is set, the
timer will deactivate after 20 seconds.
As the set time elapses, the display will show the time remaining in minutes
until it reaches one minute, after which the display changes to seconds
remaining to zero. The display will flash and a double beep alarm will sound
every ten seconds until the power button is touched or after 3 minutes, the
flashing display and alarm will deactivate.
Cooking Timer
Each element has its own cooking timer that can be activated to shut the
heating element off at the end of the set time.
At any time during cooking for each element, set the desired time duration by
first touching the clock graphic then touching the + and – buttons, holding
the button to increase or decrease the setting. A beep will sound at the start
of the setting and the set time will display in the control fame. The time
increments will run from 1-10 minutes in 1 minute increments, and then change
to 5 minute increments.
The time reading will speed up as the touch is held. Touch the timer button to
start. If no time is set, the timer will deactivate after 20 seconds and
normal cooking will resume.
As the set time elapses, the display will show the time remaining in minutes
until it reaches one minute, after which the display changes to seconds
remaining to zero. The burner will automatically shut-off and stop cooking at
the end of the set time. The display will flash and a single beep alarm will
sound every five seconds until the power button is touched, within 30 seconds.
After 30 seconds of no activity after the time has elapsed, the timer will
shut off.
Automatic Shut-Off Time
The table below displays the automatic shut-off time corresponding to each
heat setting.
SETTING | AUTOMATIC SHUT-OFF (min) |
---|---|
1 | 90 |
2 | 90 |
3 | 90 |
4 | 90 |
5 | 70 |
6 | 70 |
7 | 70 |
8 | 70 |
9 | 70 |
10 | 70 |
11 | 60 |
12 | 60 |
13 | 60 |
14 | 60 |
15 | 60 |
16 | 60 |
Temperature Guide
The following is meant to be a guideline.
Individual results may vary depending on conditions. Factors such as wind, and
outside temperatures, food temperature when placed on grill can affect cooking
times. The grill is designed and engineered for optimal cooking performance
with the lid down or closed.
SETTING | FOOD TYPES |
---|---|
1-2 | Fried eggs on griddle |
3-4 | Pancakes – French toast on griddle |
5-6 | Vegetables |
7-8 | Vegetables – Fish |
9-10 | Fish – Chicken |
11-12 | Chicken – Hamburgers |
13-14 | Hamburgers – Steaks |
15-16 | Steaks |
TEXAN GRILL WITH INTELLIKEN TOUCH™ MAINTENANCE
The Kenyon Texan Grill with IntelliKEN Touch™ is a sealed unit that does not
require regular maintenance. Please follow our operating instructions as
mentioned above. If your grill requires service, this must be preformed by
Authorized Personnel only.
Please call Kenyon Customer Care at
860-664-4906.
Error Code Readout
In the event that the Texan Grill with IntelliKEN Touch™ is not operating
correctly, the control readout will display an error code that will identify
the problem. If an error code is shown on the display, identify the code in
the Troubleshooting Index below and take action as noted.
De-power and re-start the unit to clear thedisplay. Allow the unit to cool as
necessary.
Lock out the main power supply to the unit by closing the breaker before
performing any wiring operations. If the problem persists, please call Kenyon
Customer Care at 860-664-4906, M-F, 8AM
– 5PM EST or email at
customercare@cookwithkenyon.com.
TROUBLESHOOTING INDEX
ERROR CODE | DESCRIPTION | ACTION TO REMEDY ERROR |
---|---|---|
E04 | Unit operating at high temperature. | Allow unit to cool. Ensure |
correct cooking utensil type is used. Lower the cooking level or temperature
setting.
E06 E07 E08 E09| Internal electronic control issue.| Refer
to Kenyon Customer Care.
E10| More than two control functions activated at the same time for
three seconds, unit de-powered.| Re-power unit and command one control input
at a time.
Grill Parts
Heating Elements
The heating elements are designed to pivot as shown to remove/replace the
baffle tray and drip trays. They will stay in the up position. To put down
apply slight downward pressure.
Baffle Tray
The baffle tray supports the drip trays, heating elements and grates and must
always be used when operating the grill. The cross bar must also be installed
to support the elements and grates. Drip Trays
The drip trays collect all the fat and juices created during the cooking
process. The drip trays must be emptied after each use. Whenreplacing the
drip trays, position the drip trays so that they are completely contained
inside the baffle tray and insuring that the side or the rim of the drip trays
do not protrude outside of the baffle tray.
To prevent the contents of the drip trays from smoking, place 2 cups of water
(or enough to cover the bottom of the pan) in the each drip tray before
cooking.
Grates
Grates must be cleaned after every use. The grates have a nonstick coating for
ease of cleaning. Wash grates after each use in warm soapy water.
Lid Removal
The grill lid is removable for cleaning.
To remove the lid, open it so the bearing is aligned with the notch in the
lidstay. Pull the lidstay toward the center of the grill, over the bearing,
releasing the lid from the lidstay mechanism. Then slide the quick release
pins out of the three hinges.
With the quick release
pins removed, grasp the lid, pushing back on the center to clear the middle
hinges and slide the lid to the left until the outer hinge is free of it’s
pivot pin. Once the lid has been removed it can be washed in warm, soapy
water. Installation is reverse of removal. If your grill is equipped with a
rotating handle with an LED light, be sure to remove the flashlight from the
handle prior to submersing in water. (see page 18 for removal instructions).
Rotating Handle with LED Light
Flashlight Battery Replacement The rotating lighted handle uses three
AAA batteries, which need to be replaced periodically. To replace the
batteries, unscrew the endcap from the handle to access the flashlight. Lift
the flashlight out of the cutout in the handle and then slide it out
completely.
Unscrew the bottom endcap of the flashlight to access the batteries. Replace
the batteries as shown, then tighten the endcap back onto the flashlight.
Insert the flashlight back into the handle. Ensure the light window is fully
seated into the cutout in the handle before threading the handle endcap back
on.
Rotating Lighted Handle Operation
The rotating lighted handle can be rotated downwards into two positions and is
equipped with a flashlight to illuminate the grilling area at any time of the
day. To use the handle, first open the grill lid and rotate the handle down to
the desired position. Press the button on the end of the handle to turn the
flashlight on. Press the button again to cycle through the High/Low light
settings and to turn the flashlight off.BEFORE closing the grill lid, be sure to rotate
the handle back up into its horizontal position.
The grill lid cannot be closed with the handle rotated down, and doing so can
damage the handle, grill, or countertop.
Installation
Unpacking the Grill
1 Carefully unpack the grill from its shipping container.
Verify and identify the package contents.
The following items should be included in the carton. If any components are
missing or damaged, call KENYON immediately.
Check the Electrical Supply Requirements
2 This product must be installed in accordance with national, state and local
electric codes.
Refer to table on page 5 table for the correct voltage, amperage and frequency
that must be supplied to the grill. The means for disconnection must be
incorporated in the fixed wiring in accordance with the wiring rules.
PARTS INCLUDED IMPORTANT!
If the electrical supply does not meet the product specifications, consult
with a licensed electrician before proceeding with installation!
3 Your Texan Grill with IntelliKEN Touch™ is supplied with a factory installed
polished stainless steel flange that accepts nine oval head wood screws for
mounting. The trim flange of the grill is designed to hold the unit firmly in
place in the countertop. If desired, you may seal the edge of the countertop
beneath the trim flange. We recommend a NON-ADHESIVE such as Plumbers Putty.
This will help reduce the chance of damage to the trim flange should the unit
need to be removed from the countertop. Should
you need to remove the unit from the countertop after installation simply take
a piece of fishing line and run back and forth under the trim flange to break
the caulk bond.
WARNING!
Allow a 2 inch (2”) minimum clearance between the bottom of the grill and
combustible surface located below, ie: the upper edge of a drawer installed
below the grill (see page 18). Failure to provide proper clearances and
ventilation may result in a fire hazard.
PLEASE READ THIS SECTION PRIOR TO MAKING CUTOUT FOR THE GRILL.
It is important to plan ahead for installation of the grill, keeping the
following dimensions in mind.
A – 13 inches maximum depth of overhead cabinets
B – 36 inches is minimum height of countertop above floor
C – The minimum flat countertop surface that the grill will rest upon must be
equal to or greater than the overall grill dimensions (refer to page 5 for
overall grill dimensions).
D – 30 inches minimum clearance between the top of the cooking surface and the
bottom of an unprotected wood or metal cabinet or 24 inch minimum clearance
when the bottom of the wood or metal cabinet is protected by not less than 1/4
-inch-thick flame retardant millboard covered with not less than No. 28 MSG
sheet steel, 0.015-inch-think stainless steel, 0.024-inch-thick aluminum or
0.020-inch-thickcopper.
E – 6-inch minimum from backsplash of countertop to edge of grill(refer to
page 5 for overall grill dimensions). 1-1/2 inches minimum from front of
counter to grill. FOR INSTALLATIONS IN
CANADA:
Do Not Install Closer Than 1/2 Inch (12mm)
From Any Adjacent Surface
WARNING!
To eliminate the risk of burns by reaching over heated surface units, cabinet
storage space located above surface units should be avoided. If cabinet
storage is to be provided, therisk can be reduced by installing a range hood
that projects horizontally a minimum of 5” beyond the bottom ofthe cabinets.
Before making the countertop cutout, check for clearance. Check to see if the
grill will clear the front and side walls of the base cabinet. It is also
important to provide enough ventilation. Adequate ventilation of the space
below the countertop must be provided to ensure proper operation of the grill.
Heat transferred from the grill bottom pan during operation will overheat an
improperly ventilated area.Since the appliance requires a sufficient supply of fresh air
to operate at maximum performance, the cabinet must be designed accordingly.
The following is required for this:
- The cabinet must have a minimum of two openings; one to allow fresh air to enter and the other for hot air to escape the cabinet.
- Opening sizes must be equal to 8 square inches each. This is for ambient temperatures of 85ºF / 30ºC and below. If the ambient temperature around the appliance is above 85ºF / 30ºC then larger ventilation opening sizes may be required.
When making countertop cutout, radius the corner to help prevent cracking of
the countertop material. A 1/4 inch radius is typical, but follow the
countertop manufacturer’s instructions regarding the minimum radius and any
reinforcements required to prevent damage to the countertop over time.
Use Plumber’s Putty to seal grill to countertop. Plumber’s Putty is a soft,
pliable sealing compound that is used to make watertight seals around faucets,
drains, and other plumbing parts. The putty is hidden under the flange, lip,
or edge of the grill and is not visible when the grill is installed. If caulk
were used instead of putty, it would be difficult to access these areas to cut
through the caulk to remove the part.
Plumber’s Putty is a very inexpensive material that is sold in small plastic
tubs. It is always shaped by hand before it is applied to the plumbing part.
Follow the basic instructions on the container of the Plumber’s Putty. If your
countertop is made of granite, marble, quartz, sandstone or Corian use a
stain-free Plumber’sPutty to prevent staining of the countertop.
Drain Connection
4 For your convenience, the grill is equipped with a 1/2” NPT brass pipe
fitting and 90º brass elbow which you can attach the 5/8” IDflexible hose
that came with your grill. Final Preparations Prior to Use
5
Remove the protective plastic film from the lid, trim flange and glass panel.
Clean the grill before you use it for the first time. A thorough cleaning with
a stainless steel or glass cleaner will remove any traces of plastic film
adhesives and manufacturing oils.
Wash the nonstick coated grates in warm soapy water before using the grill.
GRILLED FLANK STEAK
WITH HERB AND JALAPEÑO CHIMICHURRI SAUCE
Steak:
2 tbsp…………………….. Olive oil
2 tbsp ……………………..Worcestershire sauce
2 tbsp ……………………..Soy sauce
1 tbsp ……………………..red wine vinegar
4 cloves ……………………..garlic, minced
1 tbsp ……………………..cracked pepper
1 tsp ……………………..each salt and brown sugar
1 1/4 lb ……………………..flank steak
Chimichurri Sauce:
1/3 cup…………………….. olive oil, divided
1 small ……………………..jalapeño pepper
1/4 cup ……………………..finely chopped fresh parsley
1/4 cup…………………….. finely chopped fresh cilantro
1/4 cup…………………….. finely chopped fresh mint
2 cloves ……………………..garlic, minced
1 tbsp ……………………..lemon juice
2 tsp ……………………..red wine vinegar
1/2 tsp …………………….. salt
Instructions:
- Steak: In resealable plastic bag, stir together oil, Worcestershire sauce, soy sauce, vinegar, garlic, pepper, salt and sugar; add steak, turning to coat well. Seal and refrigerate for at least 4 hours or up to overnight.
- Add 2 cups of water to each drip tray of Texan Grill. Preheat grill for 5 to 7 minutes on high. Drain steak, discarding marinade. Cover and grill for 6 to 8 minutes per side for medium-rare or until cooked as desired. Let stand for 10 minutes; slice thinly.
- Chimichurri Sauce: Brush 1 tsp oil over jalapeño; grill, turning frequently, for 8 to 10 minutes or until tender and charred. Let cool completely; seed and chop.
- Stir together remaining oil, jalapeño, parsley, cilantro, mint, garlic, lemon juice, vinegar and salt. Serve with steak.
Tip: Substitute basil for mint if desired.
Statement of Warranty
Kenyon International, Inc (the “Company”) warrants its products in normal
usage to be free of defects in materials and workmanship subject to the
conditions and limitations below.
Any part, which proves to be defective in normal usage during the warranty
period will be repaired or replaced by the Company.
In order for product to be covered under this warranty it must be returned
to the Company for evaluation. Please
contactsupport@cookwithkenyon.com for
return instructions.
This warranty covers certain products built by the Company and is subject to
the following conditions and limitations:
-
The Company’s liability shall be limited to repair or replacement (choice of remedy at Company’s option) of electronic components as may be defective in materials or workmanship. This liability is limited to three years from the date of original installation or 42 months from invoice date, whichever comes first; this warranty covers parts and labor at pre-approved rates. Stainless steel is warranted with a lifetime guarantee to be rust free when cared for monthly as outlined in owner’s manual. If corrosion begins, contact the Company with photo evidence of corrosion for replacement components.
-
Determination of suitability of the product for the use contemplated by the Buyer is the sole responsibility of the Buyer and the Company shall have no responsibility in connection with such suitability.
-
The Company shall not be liable for any damage resulting from:
• failures due to use of the product in applications for which they are not intended;
• failures due to corrosion, wear and tear, abuse, neglect, improper installation or maintenance;
• failures due to breakage of glass, accidental or otherwise. -
The Company shall be responsible for ground shipping charges to the location of the appliance (home) within the Continental United States and Canada. Any duties, express or special shipping charges are at the expense of the Buyer. ‘
-
All labor allowed by the Company under this warranty must be pre-authorized and performed by an Authorized Kenyon International Service Center, unless otherwise specified in writing by the Company.
THERE ARE NO OTHER WARRANTIES OF MERCHANTABILITY, FITNESS FOR PURPOSE OR ANY
OTHER KIND, EXPRESSED OR IMPLIED AND NONE SHALL BE IMPLIED BY LAW. The
duration of any such warranties that are nevertheless implied by law for the
benefit of a consumer, shall be limited to a period of three years from
original purchase by the user. Some countries do not allow limitations on how
long an implied warranty lasts, so this limitation may not apply to you.
THE COMPANY SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY, WHETHER EXPRESSED, IMPLIED OR
STATUTORY. Some countries or states do not allow exclusion or limitation of
consequential or incidental damages so this limitation or exclusion may not
apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER
LEGAL RIGHTS THAT MAY VARY FROM COUNTRY TO COUNTRY AND STATE TO STATE.
Kenyon International, Inc.
P.O. Box 925 • 8 Heritage Park Road
Clinton, CT 06413 USA
Phone860-664-4906 FAX:
860-664-4907
SAVE THESE INSTRUCTIONS
Documents / Resources
|
KENYON 145739 Signature Grill With Intelliken
Touch
[pdf] Owner's Manual
145739 Signature Grill With Intelliken Touch, 145739, Signature Grill With
Intelliken Touch, Grill With Intelliken Touch, Intelliken Touch, Touch
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>