KENYON C70050 Single Zone Grill Stand Instruction Manual

KENYON C70050 Single Zone Grill Stand

Product Information

The Single Zone Grill Stand is a specialty cooking appliance manufactured by Kenyon, the world’s leading manufacturer of such appliances. The stand comes with assembly instructions that need to be followed carefully to ensure that the grill stand provides reliable service for many years.

Items Required:

• Phillips Head Hex Screwdriver
• Screwdriver (Included)
• S1 (18X) #8-32 x 5/16 Hex Drive
• Hooks (4X)
• S2 (13X) #6-32 x 1/2 Phillips Head (Important: These S2 (12x) screws replace the hardware that comes in the box of your Single Zone)
• S4 (4X) 1/4 x 1-1/4 Hex Head Optional
• Gloves and a Helping Hand Strongly Recommended
• S3 (2x) 1/4-20x 3/8 Phillips Head
• E1 (4X) Elevator Bolt Optional Included in kit but not needed for assembly

Usage Information

Part Lists:
The assembly instructions come with part lists for Side Shelf Assembly, Side Assembly, DTop Adapter, and Stationary Shelf, SZ/G2 A Grill Stand.

Assembly Instructions:

1. Read the instructions carefully before use and save them for future reference.
2. Assemble the Side Shelf Assembly and Side Assembly as per the provided part lists.
3. Use the Phillips Head Hex Screwdriver and Screwdriver to attach the S1 (18X) #8-32 x 5/16 Hex Drive and S2 (13X) #6-32 x 1/2 Phillips Head screws to the grill stand.
4. Use the Hooks (4X) to attach the Side Shelf Assembly and Side Assembly to the grill stand.
5. Attach the S4 (4X) 1/4 x 1-1/4 Hex Head screws if required.
6. Attach the S3 (2x) 1/4-20x 3/8 Phillips Head screws to the grill stand.
7. Use the E1 (4X) Elevator Bolt if required.
8. Wear gloves and ask for help if needed while assembling the grill stand.

PLEASE READ THESE INSTRUCTIONS IN THEIR ENTIRETY BEFORE USE. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

ITEMS REQUIRED

Thank you for choosing Kenyon, the world’s leading manufacturer of specialty cooking appliances. By following the instructions in this assembly manual, your grill stand will provide you with many years of reliable service.

HARDWARE

Part Lists

If any components are missing or damaged, please call KENYON Customer Service at 860-664-4906.

Assembled Stand

Instructions

Assembling Grill Stand

1. Assemble stand on a carpet or soft surface to avoid any dents or scratches. Kenyon recommends using gloves during assembly. Unpack stand parts carefully, lay the parts out to check for shipping damage.

2. Place Side Assembly and a Top Frame Panel on a flat surface. Align the top hole on the Top Frame Panel with the top hole of the leg (contained within Side Assembly). Fasten 2X of screw S1 to the corresponding holes 1 & 2 as shown in the figure below.
   Use: 2X Screw S1

3. Align the top hole of the remaining Top Frame Panel with the top hole of the oppo-site leg from Step 2 on the Side Assembly. Fasten 2X of screw S1 to the corresponding holes 3 & 4 as shown in the figure below. Use: 2X Screw S1

4. Align the Side Shelf Assembly top holes with the top holes of the Top Frame Panels. Use 4X of screw S1 to fasten the Side Shelf Assembly to both Top Frame Panels using holes 5,6,7 & 8 as shown in the figures be-low.
   Use: 4x Screw S1

5. Remove vinyl covering from the Stationary Shelf before installation. Slide the Station-ary Shelf between the legs of the stand as shown in the figure below. Fasten 8X of screw S1 to the 2 holes in each of the 4 legs. Do not fully tighten the S1 screws until all 8 screws are fastened to the legs. Use: 8X Screw S1

6. Place the Top Adapter Plate on top of the stand assembly. Use the label on the part to place the plate in the correct orienta-tion. The larger flat surface goes in the front of the stand. Use 8X S2 screws to fasten the plate to the stand using only the front and back countersunk holes as shown in the figure below. Do not fully tighten the S2 screws until all 8 screws are fastened to the Top Adapter Plate. Use: 8X Screw S2

7. Fasten 2X S3 screws to the corresponding holes 9&10 as shown in the figure below. Do not tighten all the way. Place Side Tray onto Side Assembly by aligning the keyholes on the Side Tray with the 2X S3 screws.
   Use: 2X Screw S3

8. Place your Single Zone Grill into the cutout of the Top Adapter Plate as shown in the figure below. Fasten the grill to the plate using 4X S2 screws in the 4 corners of the grill flange.
   Use: 4X Screw S2

9. Optional: If using the hex head screws S4 to fasten the stand to a deck or patio, first find the install location to set the stand. Use 4X S4 screws to fasten the stand to a deck or patio. If you are not mounting the stand to a deck or patio, instead use the included E1 elevator bolts with jam nuts which can be screwed into the bottom of each leg for your convenience.
   Use: 4X Screw S4 OR 4X Elevator Bolt with Jam Nut E1

10. Congratulations, your Single Zone Grill Stand has been assembled! Take this time to tighten all fasteners.

11. The Folding Shelf can be lifted and lowered into position by lifting both levers on the brackets underneath. Although there are rub-ber caps on the levers to protect your stand, do not let the Folding Shelf fall into the down position.

12. The Folding Shelf can be lifted and lowered into position by lifting both levers on the brackets underneath. Although there are rubber caps on the levers to protect your stand, do not let the Folding Shelf fall into the down position.

13. Take the remaining vinyl off and use this time to clean and polish to put a beautiful shine on the grill and stand. Remember
    to wipe with the grain of the sheet metal. Never wipe across or diagonally. We have included a sample of stainless-steel polish for your convenience.

14. There are 4 hooks included in this package. The hooks can be used to hang your grilling accessories wherever you would like. Be aware that once the hooks are applied, they cannot be adjusted without damaging the surface they are attached to. The hooks are applied using a very high bond tape. Thor-oughly clean the area where you want the hooks installed. Peel the protective layer off the double-sided tape located on the back of the hook and firmly apply the hook to the desired location on the stand. Allow the ad-hesive to set for 2 hours prior to putting any load on the hook.

Congratulations, go grill your favorite food!
If you have any questions or concerns while assembling, please do not hesitate to call Kenyon customer service at 860-664-4906.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>