WANGFENG MK8125B Remote Control Car Instruction Manual
- June 26, 2024
- WANGFENG
Table of Contents
WANGFENG MK8125B Remote Control Car
Product Information
- Item No.: MK8125B Remote control car series
- Frequency: 2.4GHz
Specifications
- Remote Control Car Series: MK8125B
- Frequency: 2.4GHz
- Battery Requirement: 2 x 1.5V AA batteries for remote control
- Compliance: FCC Part 15
Product Usage Instructions
Remote Control Battery Installation
- Open the battery cover on the remote control.
- Insert 2 x 1.5V AA batteries into the compartment, observing the correct polarity.
- Close the battery cover securely.
- Ensure the switch on the remote control is in the OFF position before replacing the batteries.
Troubleshooting
- Reorient or relocate the receiving antenna if experiencing signal issues.
- Increase the separation between the remote control car and the receiver for better connectivity.
- If interference persists, connect the equipment to a different outlet on a separate circuit.
- If problems persist, consult the dealer or a radio/TV technician for assistance.
Safety Information
Changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment. This device complies with FCC Part 15 regulations, ensuring minimal interference and reliable operation.
Remote control car series
Operation Instructions 2.4GHz
-
Remote control car battery installation
-
Turn the power switch to “OFF” and open the battery cover;
-
Dry battery
-
Take high-performance alkaline batteries (4*1.5V “AA” LR6 batteries)Load in the direction shown, ensure proper installation, and close the battery cover
-
Rechargeable battery
-
Before using the car for the first time or has not been used for a long time, the 3.7V lithium battery can be charged by a charging device with a USB jack (e.g. desktop computer, laptop, mobile power supply, USB power outlet, or via a USB adapter).
-
Insert the USB plug into the charging device socket with the USB connector to connect the power supply; At this time, the indicator light on the USB charging plug will light up, and the indicator light will dim when the battery is saturated, indicating that the battery has been charged; It takes about 3 to 4 hours to fully charge
-
If the light is not on after connection, it means there is a problem with the line or battery. Please switch the USB plug to stop charging as soon as possible, and it can be charged again after maintenance;
Please ensure that the USB interface power supply is smooth before charging; -
The rechargeable battery is slightly hot when charging, which is normal.
-
-
Remote control battery installation
- Put 2*1.5V”AA” batteries in the remote control and cover the battery cover. (Please switch the switch to the “OFF” position to replace the battery
-
Frequency correspondence
- The remote control needs to be associated with the car before it is used each time. Specific steps are as follows:
- Ensure that the remote control, remote control car’s power is sufficient.
- Move the remote control to the “ON” position, the remote control indicator blinks, prompting you to enter the code state. Open the remote control car switch (that is, the power switch under the car is turned to the “ON” position), at this time the remote control indicator is off, indicating that the correlation code is completed, you can freely control the functions of the car, as shown in the figure.
- The 2.4GHz remote control car has the function of multiple cars operating at the same time. It can be played by many people without interference, but it must be carried out one by one when the code is associated, according to the above operation steps for the first car association code, the code after the remote control and car power must remain open, and then by the same method for the second car association code, and so on.
- After use, please be sure to switch the remote control and remote control car to the “OFF” position.
-
Precautions
- Different types of batteries/old and new batteries can not be mixed, used batteries should be taken out of the toy.
- The replacement of the battery should be under adult supervision, the battery should be put into the correct polarity, and the power supply cannot be short-circuited.
- Non-rechargeable batteries can not be charged, rechargeable batteries should be taken out of the toy before charging and should only be charged under adult supervision, if the battery is damaged or leaked, do not charge.
- Only batteries of the same model or the same model as recommended can be used.
- The iron wire and electric wire can not be plugged into the output socket.
- The battery should not be near fire or any heat source, should not be stained with water, and can not be beaten or exposed to the sun.
- If you get battery leakage on your skin or clothing, rinse immediately.
- It is necessary to check whether the wires, plugs, shells and other parts are damaged regularly. If they are damaged, stop using them until they are repaired.
-
Operation attention
- Straight driving: Adjust the car bottom trimmer to make the car travel straight.
- When the light of the remote control turns dark, it indicates that the battery is insufficient and needs to be replaced.
- When the speed of the remote control car slows down and the light of the remote control car dims the battery power is insufficient, the a need to replace the battery or charge the charging battery in time.
- Need to change the remote control or remote control car battery when the power is low or some functions can not be reflected or even out of control phenomenon,
- Do not drive your car into sand, water or snow, as it will damage the product; Do not point the remote control car at people or animals to impact;
- Don’t let your car near the heat or directly in the sun, please disconnect the power when not playing.
- Please point the antenna of the remote control at the remote control car, and control the remote control car within the effective distance that can be seen, so as not to affect the play effect;
- Use time: The factory set the normal use time of products is 20-25 minutes, the specific use time depends on your control method.
FCC
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by theinstructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
Frequently Asked Questions
- Q: What should I do if the remote control car does not respond to commands?
- A: Check the battery levels in both the car and remote control. Ensure the batteries are properly installed with correct polarity and that there is no signal interference.
- Q: How far can I control the remote control car?
- A: The effective range of the remote control is approximately XX meters, depending on environmental factors such as obstacles and interference.