Global Commander PEG Series Electric Baseboard Heater Installation Guide
- June 24, 2024
- Global Commander
Table of Contents
Global Commander PEG Series Electric Baseboard Heater
Specifications
- Product: Electric Baseboard Heater PEG Series
- Installation: Must be executed by a qualified technician
- Recommended clearance for furniture and drapes: 3 in. (76.2 mm)
FAQ
Q: Can this heater be used in bathrooms?
A: For bathroom use, ensure that switches and controls are out of reach from bath or shower. This product is not recommended with a ground fault circuit interrupter (GFCI) due to potential leakage current issues.
1 800 463-7043 • www.globalcommander.ca
INSTALLATION INSTRUCTIONS Electric Baseboard Heater PEG Series
THE INSTALLATION MUST BE EXECUTED BY A QUALIFIED TECHNICIAN
RISK OF ELECTROCUTION
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be taken to reduce the risk of fire, electric shock, and injury, including the following: Read all instructions before using this heater.
- A heater has hot and arcing or sparking parts inside.
- Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, like furniture, pillows, bedding, papers, clothes, and curtains away from heater.
- To prevent a possible fire, do not block air intakes or exhaust in any way whatsoever.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- Do not install heater against combustible low-density cellulose fiberboard surfaces.
- Do not use outdoors.
- WARNING – High Temperature; Keep electrical cords, drapes, and other furnishings away from heater.
- Use only with copper branch circuit conductors.
- The heater has been designed and certified for ambient heating only. The maximum ambient operating temperature is 30 °C (86 °F).
- The heater is not designed for use in a humid environment where condensation may form on the device.
- Do not install this heating appliance beneath a wall outlet.
- To avoid possible electrical shock, disconnect all power at the main panel prior to wiring, cleaning, or servicing.
- If the product is damaged or has missing parts (e.g., dents, damaged or missing element fins), stop using the device immediately and replace it.
SAVE THESE INSTRUCTIONS.
FURNITURE AND DRAPES
- For maximum satisfaction an air flow of 3 in. (76.2 mm)clearance is recommended.
- Also allow 1 in. (25.4 mm) clearance on top and bottom of drapes when drapes cover wall.
- In addition to ensuring that the clearance distances set out above are respected, ensure that the framing materials, insulation and finishing which are likely to be in contact with or close to the device can withstand temperatures of at least 90 °C (194 °F).
INSTALLATION INSTRUCTIONS
CAUTION
For bathroom use, the heater must be installed so that switches and other controls cannot be touched by anyone in the bath or shower.
This product is not recommended with the ground fault circuit interrupter (GFCI). The humidity in the air can generate a leakage current higher than the limit of the GFCI which will cause the product to stop.
- Remove wire holder (or knock-out) of the appropriate junction box.
- Make connection according to local and national codes and replace wire holder. (Do not forget ground wire.)
- Install the relay or thermostat by removing front panel and junction box cover.
- Check wire connection at the other junction box.
- Fasten the baseboard to the wall using wood screws, tighten then release 1/2 turn.
- Replace all covers before energizing.
INTERCONNECTION
The connection boxes and wiring channel are approved for inter-connection of baseboard heaters and components which are on the same heating branch circuit. Use ‘‘BX’’ cable to run wiring for all other options in this series. (Ex: Corner box, empty cabinets, etc.).The heater junction box minimum volume without options is 31.2 in³ (512 cm³).
CORNERS AND BLANK SECTIONS
Install blank sections and corners the same way as heating unit of this
series. Use ‘‘BX’’cable to run wiring into these options.
OPTIONS
All heating equipment and options must be installed in accordance with local
and national codes.
Built-in thermostat:
CAUTION: The thermostat should not be considered as an infallible system where maintaining a temperature is considered critical. Examples: Hazardous material storage, computer room, etc. In these particular cases, it is imperative to add a monitoring system to avoid the consequences of a failure of the thermostat.
- Refer to wiring diagram for connections.
- Refer to instructions supplied with the option for mounting.
Built-in relay:
- Refer to the diagram included with the relay option for connections.
- Refer to instructions supplied with the option for mounting.
MAINTENANCE
- Once a year or at the need, remove the front panel and use a vacuum cleaner to remove the dust accumulation inside the heater.
- Cleaning should be done while the heater is disconnected from the main service panel. Wait until the housing and heating element cool before performing maintenance.
Remove the front panel.
CAUTION: Fins on the element are sharp – Do not touch.
Replace all covers before energizing.
Any other servicing should be performed by a qualified technician.
WARRANTY
Please refer to the specification sheet at
www.globalcommander.ca.
INS393-201204-03
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>