GRIVEN GoboLED 500 Image Projector User Manual

: June 23, 2024
: GRIVEN

Table of Contents

GRIVEN GoboLED 500 Image Projector
Dimensions
Important notices
Installation
Preliminary operations
Connection
Control panel operations
Trouble shooting
DMX Chart
Configuration example
Gobos replacing ( rotating gobo wheel )
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GRIVEN GoboLED 500 Image Projector

AL5179

Power consumption| 550 W (LED+ motors + Heater) – 360 W (LED + motors only)
---|---
Nominal current| 2.5 A (LED+ motors + Heater) – 1.6 A (LED + motors only)
Power supply| 100 – 240 VAC 50/60Hz
Inrush current| 35 A @ 230 VAC, cold start, 1800 μs.
Power factor| cos.φ= 0.95
Electrical class| I
Weight| 30 Kg
Operating temperature| -30°C to +50°C ( -22°F to 122°F )
IP rating| IP66
IK rating| IK07
Housing| Steel/alluminium, scratch resistant paint
Thermal protection| Integrated electronic thermal protection management
Cable| 1.5 m
Control| USITT DMX-512, RDM
Channels| 14
Source & colors| 1 high output LED 8000K, 8 colours+ white wheel
Gobos| 7 rotating gobos (ø27/22 mm) wheel + 4 fixed gobos plus effect wheel
Other features| 2 prisms, linear 0-100% dimmer, strobe function (27.7 fps max), pulse and zap effect, electronic blackout, motorized electronic focus, motorized linear zoom

Dimensions

Important notices

This product must be installed in accordance with applicable national and local electrical and construction codes by a person familiar with the construction and operation of the product and the hazards involved. Failure to comply with the following installation instructions may result in death or serious injury.
Do not stare at the operating light source.
The ﬁ xture might be damaged by excess voltage. The installation of an overvoltage protection device on the electrical system (SPD) is recommended for reduce the risk of damage.
The use of an adequate magnetothermic switch along the power supply line is recommended.
Connect the ﬁ xtures to each other only when disconnected from mains.
Never leave cables and connectors unconnected or unprotected for long periods.
Disconnect power before installing or servicing to avoid electrical shock.
Disconnect power before any connection operation.
Check voltage and frequency before powering the ﬁ xture. Do not exceed ﬁ xture speciﬁ ed voltage.
Do not handle the unit with wet hands or in wet environments.
Apply to qualiﬁ ed staff for any maintenance service not described in this instructions manual.
Do not exceed the maximum quantity of ﬁ xtures per line in order to avoid power surges.
Before powering the unit, ensure to use cables and connectors with proper section and length, according to its power consumption.
Fix the projector by using screws, hooks or other adequate supports that can bear its weight.

CAUTION : Prolonged staring at LED source should be avoided by placing the fixture in a proper position.
WARNING! fixing and connecting operations must mandatorily be carried out by qualified personnel only !
WARNING! Ensure power supply is off before connecting or disconnecting fixtures !
CAUTION : The fixture has a heavy weight. It is suggested to handle it by two persons.

Installation

CAUTION : prolonged staring at the LED source should be avoided by placing the fixture in a proper position.

Preliminary operations

In order to connect the unit to a DMX controller, pull out the input and output DMX cables from the back of the fixture. Follow the below reported instructions.

Connection

WARNING the cables connections must be carried out by using the optional connection kit. Follow the instructions provided along with the connection kit.

WARNING Fixing and connecting operations must mandatorily be carried out by qualified personnel only
WARNING Make sure that power supply is off before connecting or disconnecting fixtures !

Control panel operations

In order to access the control panel of the fixure undo the four screws as shown in the picture. After performing the operation required, close the cover by tightening the screws.

Menu explanation

Automatic Master function

Trouble shooting

DMX Chart

Chn.l	Function	Values

1

| ****

DIMMING LED

| 0~5| Led off
6~240| Proportional dimming (Min. to Max.)
241~255| Led On
2| PULSE AND STROBE| 0~5| No effect
6~10| Reset ( wait 5 seconds to activate )
11~20| Pulse up 1 (slow)
21~30| Pulse up 2
31~40| Pulse up 3
41~50| Pulse up 4
51~60| Pulse up 5
61~70| Pulse up 6
71~80| Pulse up 7 (fast)
81~90| Led Off
91~100| Pulse down 1 (slow)
101~110| Pulse down 2
111~120| Pulse down 3
121~130| Pulse down 4
131~140| Pulse down 5
141~150| Pulse down 6
151~160| Pulse down 7 (fast)
161~170| Led Off
171~180| Strobe 1 (slow)
181~190| Strobe 2
191~200| Strobe 3
201~210| Strobe 4
211~220| Strobe 5
221~230| Strobe 6
231~240| Strobe 7 (fast)
241~255| No effect
3| COLOR WHEEL| 0~2| White
3~12| White + Red
13~17| Red
18~26| Red + Blue
27~31| Blue
32~40| Blue + Yellow
41~45| Yellow
46~54| Green + Yellow
55~59| Green
60~78| Green + Pink
Chn.l| Function| Values
---|---|---
| | 69~73| Pink
74~82| Pink + Orrange
83~87| Orange
88~96| Orange + CTO
97~101| CTO
102~110| CTO + UV
111~115| UV
116~125| UV + White
126~132| White
133~183| Proportional clockwise rotation
184~194| White
195~244| Proportional counterclockwise rotation
245~255| White
4| GOBO ROTATION WHEEL SELECTION| 0~15| Open
16~30| Gobo 1
31~45| Gobo 2
46~60| Gobo 3
61~75| Gobo 4
76~90| Gobo 5
91~105| Gobo 6
106~120| Gobo 7
121~180| Proportional clockwise rotation of the wheel (MIn. to Max.)
181~190| Open
191~250| Proportional counterclockwise rotation of the wheel (Max. to Min.)
251~255| Open
5| ****

GOBOS ROTATION

6

| ****

GOBOS INDEXING

| 0~7| No effect
8~248| 360° gobo indexing
249~255| No effect

7

| GOBOS FINE INDEXING| ****

0~255

| ****

Proportional fne gobo indexing

8

| FIXED GOBO WHEEL| 0~10| Open
11~20| Gobo 1
21~30| Gobo 2
Chn.l| Function| Values
---|---|---
| | 31~40| Gobo 3
41~50| Gobo 4
51~100| Proportional clockwise and anti-clockwise rotation, with different speed, one way till end and return to beginning.
101~160| Proportional clockwise rotation of the wheel (Max. to min.)
161~170| Open
171~230| Proportional counterclockwise rotation of the wheel (Min. to max.)
231~255| Open
9| ZOOM| 0~255| Proportional linear position
10| FOCUS| 0~255| Proportional linear position

11

| ****

PRISM WHEEL SELECTION

12

| ****

PRISM ROTATION

(blackout during motor positioning )

(priority and distan- ce selection)

| 0~27| Disable zoom/focus linking – 1 sec.
28~52| Enable zoom/focus linking, near distance (5meters)( default setting )-1 sec
53~77| Enable zoom/focus linking, near distance (6meters)( default setting )-1 sec
78~102| Enable zoom/focus linking, medium distance (8meters) – 1 sec
103~127| Enable zoom/focus linking, far distance (12meters) – 1 sec
128~255| No effect

RDM functions
When operating in DMX mode the fixture can accept the following RDM commands:

discovery: Upon request of the RDM controller, the fixture signals its own presence (the RDM controller will display the fixture on a list).
DMX address reading and setting.
Channels number reading and setting.
On / Off identification: This command is used to identify the fixture you want to get access to (the identification happens by switching on all the LEDs at full intensity).
Manufacturer: it displays the name of the manufacturer (Griven).
Model description: it displays the fixture’s model.
Software version description: it displays the current version of the firmware.
Temperature: it displays the LEDs operating temperature value.

Configuration example

A= DMX controller
B= 100-240 VAC 50/60 Hz
C= 120 Ω DMX Terminator
*DMX cable type: 2×0.34 mmq impedance 110Ω, capacity 43pF/m, resistance 50Ω/Km.

WARNING

Use a DMX repeater on each 32nd fixture of the daisy-chain or in case the total DMX cable lenght exceeds 300m ( 1000 ft.). Install a data terminator ( 120Ω) on the DMX out cable of the last unit of the daisy-chain as described in the DMX connection kit manual.
Being a mechanical equipment, it could possibly have a variation in the holographic reproduction of about 10cm (0.33 ft) on 3000cm (98.40 ft)

Heating and cooling system notice
GoboLed 500 is provided with an intelligent heating/cooling system that allows to operate also in very cold ( down to -30°C /- 40°F) or hot ( +50° / 122 °F) environments. When powered on at very low temperatures, the unit takes some minutes to reach the optimal internal tempera-ture and to allow proper operation. At normal temperatures the cooling fan may start and stop automatically due to the internal temperature management system that prevents the LED from overheating .

WARNING Do not cover or obstruct any of the ventilation grid placed on the fixture. It is highly recommended regularly to inspect and clean these grids. The obstruction of the grids can seriously compromise the proper operation of the unit.